Applied sciences

Archive of Mechanical Engineering

Content

Archive of Mechanical Engineering | 2009 | vol. 56 | No 4 |

Download PDF Download RIS Download Bibtex

Abstract

Modification of the FanWing concept intended for the use at higher speeds of flight (over 20 m/s) is numerically analyzed. The principle of operation, basic aerodynamic characteristics, and the features in untypical flight situation (autorotation) are described and explained.

Go to article

Authors and Affiliations

Krzysztof Kurec
Janusz Piechna
Download PDF Download RIS Download Bibtex

Abstract

This paper presents a new method of calculation of the change of axial twisting angle of compressed helical spring’s end-coils in the case of rotary - free supports. The propriety of derived formulas was experimentally verified. The method is easy in application and gives results much closer to experiment than the presently used method that can be found in literature.

Go to article

Authors and Affiliations

Krzysztof Michalczyk
Download PDF Download RIS Download Bibtex

Abstract

The paper presents strength examination for premolar dental crowns reconstructed with glass fibre dowels in terms of normal occlusal loadings. For comparison, strength examination of fillings retention was also done for crown reconstructions without dowels as well as for the so-called healthy teeth. The analyses of the results have shown a good quality of fillings reconstructed using the glass fibre technique and proved their durability and high strength properties.

Go to article

Authors and Affiliations

Grzegorz Milewski
Maciej Żarow
Marcin Klaus
Download PDF Download RIS Download Bibtex

Abstract

In the paper, author presents the analysis of the elastic-plastic residual stresses and the boundaries of plastic zones in two-dimensional model with central circular hole. The experimental testing was carried out by photoelastic coating method. The duralumin model was loaded within the overelastic range by uniformly distributed tensile stresses. For various levels of loading, the photographs of isochromatic pattern were taken. The residual stresses along the axis of symmetry perpendicular to the stretching direction were calculated by the characteristics method, using multisectional schematization of ϭ-ε relation for the material. The boundaries of plastic zones in the loaded model were obtained on the basis of the Treska-Coulomb yield condition directly from the isochromatic pattern. The analysis and discussion of the test results is presented.

Go to article

Authors and Affiliations

Barbara Kozłowska
Download PDF Download RIS Download Bibtex

Abstract

The present paper investigates the effects of variable-amplitude loads on fatigue crack growth rates for the 2024-T3 aluminium alloy on the basis of microfractographic analyses and its capacity to reconstruct load-time histories of failed components. For this purpose, there were applied three different variable-amplitude load sequences with single and multiple overloads and underloads. Subsequently, images of fatigue striations on components’ fracture surfaces were examined. The aforementioned loads were employed when simulating fatigue crack behaviour in aeronautical alloys.

Go to article

Authors and Affiliations

Zdzisław Bogdanowicz
Dorota Kocańda
Janusz Torzewski
Download PDF Download RIS Download Bibtex

Abstract

The paper presents experimental results of creep and low cycle fatigue (LCF) tests carried out on the as-received cast aluminium alloys with different chemical composition and porosity. The test programmes contain creep investigations under step-increased stresses at different temperatures, and cyclic plasticity under different strain amplitudes and temperatures.

Go to article

Authors and Affiliations

Lech Dietrich
Agnieszka Rutecka
Zbigniew Kowalewski
Download PDF Download RIS Download Bibtex

Abstract

A mathematical model, created for description of the mechanism of interaction between basic parameters of high pressure dispersion of emulsions, is presented in this paper. The model is applied for the analysis of the influence of physical properties of emulsions, quantitative content of dispersed emulsion phase and parameters of emulsification, pressure and temperature, on the characteristic dimension of particles of the dispersed phase. The model makes it possible to determine appropriate process parameters, especially the pressure necessary to obtain the required dispersion of the emulsion and to define construction and exploitation parameters of high-pressure emulsification valve.

Go to article

Authors and Affiliations

Artur Popko

Instructions for authors

About the Journal
Archive of Mechanical Engineering is an international journal publishing works of wide significance, originality and relevance in most branches of mechanical engineering. The journal is peer-reviewed and is published both in electronic and printed form. Archive of Mechanical Engineering publishes original papers which have not been previously published in other journal, and are not being prepared for publication elsewhere. The publisher will not be held legally responsible should there be any claims for compensation. The journal accepts papers in English.

Archive of Mechanical Engineering is an Open Access journal. The journal does not have article processing charges (APCs) nor article submission charges.

Outline of procedures
  • To ensure that high scientific standards are met, the editorial office of Archive of Mechanical Engineering implements anti-ghost writing and guest authorship policy. Ghostwriting and guest authorship are indication of scientific dishonesty and all cases will be exposed: editorial office will inform adequate institutions (employers, scientific societies, scientific editors associations, etc.).
  • To maintain high quality of published papers, the editorial office of Archive of Mechanical Engineering applies reviewing procedure. Each manuscript undergoes crosscheck plagiarism screening. Each manuscript is reviewed by at least two independent reviewers.
  • Before publication of the paper, authors are obliged to send scanned copies of the signed originals of the declaration concerning ghostwriting, guest authorship and authors contribution and of the Open Access license.
Submission of manuscripts

The manuscripts must be written in one of the following formats:
  • TeX, LaTeX, AMSTeX, AMSLaTeX (recommended),
  • MS Word, either as standard DOCUMENT (.doc, .docx) or RICH TEXT FORMAT (.rtf).
All submissions to the AME should be made electronically via Editorial System – an online submission and peer review system at https://www.editorialsystem.com/ame. First-time users must create an Author’s account to obtain a user ID and password required to enter the system. All manuscripts receive individual identification codes that should be used in any correspondence with regard to the publication process. For the authors already registered in Editorial System it is enough to enter their username and password to log in as an author. The corresponding author should be identified while submitting a paper – personal e-mail address and postal address of the corresponding author are required. Please note that the manuscript should be prepared using our LaTeX or Word template and uploaded as a PDF file.

If you experience difficulties with the manuscript submission website, please contact the Assistant to the Editor of the AME (ame.eo@meil.pw.edu.pl).

All authors of the manuscript are responsible for its content; they must have agreed to its publication and have given the corresponding author the authority to act on their behalf in all matters pertaining to publication. The corresponding author is responsible for informing the co-authors of the manuscript status throughout the submission, review, and production process.

Length and arrangement

Papers (including tables and figures) should not exceed in length 25 pages of size 12.6 cm x 19.5 cm (printing area) with a font size of 11 pt. For manuscript preparation, the Authors should use the templates for Word or LaTeX available at the journal webpage. Please notice that the final layout of the article will be prepared by the journal's technical staff in LaTeX. Articles should be organized into the following sections:
  • List of keywords (separated by commas),
  • Full Name(s) of Author(s), Affiliation(s), Corresponding Author e-mail address,
  • Title,
  • Abstract,
  • Main text,
  • Appendix,
  • Acknowledgments (if applicable),
  • References.
Affiliations should include department, university, city and country. ORCID identifiers of all Authors should be added.
We suggest the title should be as short as possible but still informative.

An abstract should accompany every article. It should be a brief summary of significant results of the paper and give concise information about the content of the core idea of the paper. It should be informative and not only present the general scope of the paper, but also indicate the main results and conclusions. An abstract should not exceed 200 words.

Please follow the general rules for writing the main text of the paper:
  • use simple and declarative sentences, avoid long sentences, in which the meaning may be lost by complicated construction,
  • divide the main text into sections and subsections (if needed the subsections may be divided into paragraphs),
  • be concise, avoid idle words,
  • make your argumentation complete; use commonly understood terms; define all nonstandard symbols and abbreviations when you introduce them;
  • explain all acronyms and abbreviations when they first appear in the text;
  • use all units consistently throughout the article;
  • be self-critical as you review your drafts.
The authors are advised to use the SI system of units.

Artwork/Equations/Tables

You may use line diagrams and photographs to illustrate theses from your text. The figures should be clear, easy to read and of good quality (300 dpi). The figures are preferred in a vector format (bitmap formats are acceptable, but not recommended). The size of the figures should be adequate to their contents. Use 8-9pt font size of the text within the figures.

You should use tables only to improve conciseness or where the information cannot be given satisfactorily in other ways. Tables should be numbered consecutively and referred to within the text by numbers. Each table should have an explanatory caption which should be as concise as possible. The figures and tables should be inserted in the text file, where they are mentioned.

Displayed equations should be numbered consecutively using Arabic numbers in parentheses. They should be centered, leaving a small space above and below to separate it from the surrounding text.

Footnotes/Endnotes/Acknowledgements

We encourage authors to restrict the use of footnotes. Information concerning research grant support should appear in a separate Acknowledgements section at the end of the paper. Acknowledgements of the assistance of colleagues or similar notes of appreciation should also appear in the Acknowledgements section.

References
References should be numbered and listed in the order that they appear in the text. References indicated by numerals in square brackets should complete the paper in the following style:

Books:
[1] R.O. Author. Title of the Book in Italics. Publisher, City, 2018.

Articles in Journals:
[2] D.F. Author, B.D. Second Author, and P.C. Third Author. Title of the article. Full Name of the Journal in Italics, 52(4):89–96, 2017. doi: 1234565/3554. (where means: 52 – volume; 4 – number or issue; 89–96 – pages, and 1234565/3554 – doi number (if exists).)

Theses:
[3] W. Author. Title of the thesis. Ph.D. Thesis, University, City, Country, 2010.

Conference Proceedings:
[4] H. Author. Title of the paper. In Proc. Conference Name in Italics, pages 001–005, Conference Place, 10-15 Jan. 2015. doi: 98765432/7654vd.

English language

Archive of Mechanical Engineering is published in English. Make sure that your manuscript is clearly and grammatically written. The content should be understandable and should not cause any confusion to the readers, including the reviewers. After accepting the manuscript for a publication in the AME, we offer a free language check service, for correcting small language mistakes.

Submission of Revised Articles

When revision of a manuscript is requested, authors are expected to deliver the revised version of the manuscript as soon as possible. The manuscript should be uploaded directly to the Editorial System as an answer to the Editor's decision, and not as a new manuscript. If it is the 1st revision, the authors are expected to return revised manuscript within 60 days; if it is the 2nd revision, the authors are expected to return revised manuscript within 14 days. Additional time for resubmission must be requested in advance. If the above mentioned deadlines are not met, the manuscript may be treated as a new submission.

Outline of the Production Process

Once an article has been accepted for publication, the manuscript is transferred into our production system to be language-edited and formatted. Language/technical editors reserve the privilege of editing manuscripts to conform with the stylistic conventions of the journal. Once the article has been typeset, PDF proofs are generated so that authors can approve all editing and layout.

Proofreading

Proofreading should be carried out once a final draft has been produced. Since the proofreading stage is the last opportunity to correct the article to be published, the authors are requested to make every effort to check for errors in their proofs before the paper is posted online. Authors may be asked to address remarks and queries from the language and/or technical editors. Queries are written only to request necessary information or clarification of an unclear passage. Please note that language/technical editors do not query at every instance where a change has been made. It is the author's responsibility to read the entire text, tables, and figure legends, not just items queried. Major alterations made will always be submitted to the authors for approval. The corresponding author receives e-mail notification when a PDF is available and should return the comments within 3 days of receipt. Comments must be uploaded to Editorial System.

Reviewers


The Editorial Board of the Archive of Mechanical Engineering (AME) sincerely expresses gratitude to the following individuals who devoted their time to review papers submitted to the journal. Particularly, we express our gratitude to those who reviewed papers several times.

List of reviewers of volume 68 (2021)
Ahmad ABDALLA – Huaiyin Institute of Technology, China
Sara ABDELSALAM – University of California, Riverside, United States
Muhammad Ilman Hakimi Chua ABDULLAH – Universiti Teknikal Malaysia Melaka, Malaysia
Hafiz Malik Naqash AFZAL – University of New South Wales, Sydney, Australia
Reza ANSARI – University of Guilan, Rasht, Iran
Jeewan C. ATWAL – Indian Institute of Technology Delhi, New Delhi, India
Hadi BABAEI – Islamic Azad University, Tehran, Iran
Sakthi BALAN – K. Ramakrishnan college of Engineering, Trichy, India
Leszek BARANOWSKI – Military University of Technology, Warsaw, Poland
Elias BRASSITOS – Lebanese American University, Byblos, Lebanon
Tadeusz BURCZYŃSKI – Institute of Fundamental Technological Research, Warsaw, Poland
Nguyen Duy CHINH – Hung Yen University of Technology and Education, Hung Yen, Vietnam
Dorota CHWIEDUK – Warsaw University of Technology, Poland
Adam CISZKIEWICZ – Cracow University of Technology, Poland
Meera CS – University of Petroleum and Energy Studies, Duhradun, India
Piotr CYKLIS – Cracow University of Technology, Poland
Abanti DATTA – Indian Institute of Engineering Science and Technology, Shibpur, India
Piotr DEUSZKIEWICZ – Warsaw University of Technology, Poland
Dinesh DHANDE – AISSMS College of Engineering, Pune, India
Sufen DONG – Dalian University of Technology, China
N. Godwin Raja EBENEZER – Loyola-ICAM College of Engineering and Technology, Chennai, India
Halina EGNER – Cracow University of Technology, Poland
Fehim FINDIK – Sakarya University of Applied Sciences, Turkey
Artur GANCZARSKI – Cracow University of Technology, Poland
Peng GAO – Northeastern University, Shenyang, China
Rafał GOŁĘBSKI – Czestochowa University of Technology, Poland
Andrzej GRZEBIELEC – Warsaw University of Technology, Poland
Ngoc San HA – Curtin University, Perth, Australia
Mehmet HASKUL – University of Sirnak, Turkey
Michal HATALA – Technical University of Košice, Slovak Republic
Dewey HODGES – Georgia Institute of Technology, Atlanta, United States
Hamed HONARI – Johns Hopkins University, Baltimore, United States
Olga IWASINSKA – Warsaw University of Technology, Poland
Emmanuelle JACQUET – University of Franche-Comté, Besançon, France
Maciej JAWORSKI – Warsaw University of Technology, Poland
Xiaoling JIN – Zhejiang University, Hangzhou, China
Halil Burak KAYBAL – Amasya University, Turkey
Vladis KOSSE – Queensland University of Technology, Brisbane, Australia
Krzysztof KUBRYŃSKI – Air Force Institute of Technology, Warsaw, Poland
Waldemar KUCZYŃSKI – Koszalin University of Technology, Poland
Igor KURYTNIK – State Higher School in Oswiecim, Poland
Daniel LESNIC – University of Leeds, United Kingdom
Witold LEWANDOWSKI – Gdańsk University of Technology, Poland
Guolu LI – Hebei University of Technology, Tianjin, China
Jun LI – Xi’an Jiaotong University, China
Baiquan LIN – China University of Mining and Technology, Xuzhou, China
Dawei LIU – Yanshan University, Qinhuangdao, China
Luis Norberto LÓPEZ DE LACALLE – University of the Basque Country, Bilbao, Spain
Ming LUO – Northwestern Polytechnical University, Xi’an, China
Xin MA – Shandong University, Jinan, China
Najmuldeen Yousif MAHMOOD – University of Technology, Baghdad, Iraq
Arun Kumar MAJUMDER – Indian Institute of Technology, Kharagpur, India
Paweł MALCZYK – Warsaw University of Technology, Poland
Miloš MATEJIĆ – University of Kragujevac, Serbia
Norkhairunnisa MAZLAN – Universiti Putra Malaysia, Serdang, Malaysia
Dariusz MAZURKIEWICZ – Lublin University of Technology, Poland
Florin MINGIREANU – Romanian Space Agency, Bucharest, Romania
Vladimir MITYUSHEV – Pedagogical University of Cracow, Poland
Adis MUMINOVIC – University of Sarajevo, Bosnia and Herzegovina
Baraka Olivier MUSHAGE – Université Libre des Pays des Grands Lacs, Goma, Congo (DRC)
Tomasz MUSZYŃSKI – Gdansk University of Technology, Poland
Mohamed NASR – National Research Centre, Giza, Egypt
Driss NEHARI – University of Ain Temouchent, Algeria
Oleksii NOSKO – Bialystok University of Technology, Poland
Grzegorz NOWAK – Silesian University of Technology, Gliwice, Poland
Iwona NOWAK – Silesian University of Technology, Gliwice, Poland
Samy ORABY – Pharos University in Alexandria, Egypt
Marcin PĘKAL – Warsaw University of Technology, Poland
Bo PENG – University of Huddersfield, United Kingdom
Janusz PIECHNA – Warsaw University of Technology, Poland
Maciej PIKULIŃSKI – Warsaw University of Technology, Poland
T.V.V.L.N. RAO – The LNM Institute of Information Technology, Jaipur, India
Andrzej RUSIN – Silesian University of Technology, Gliwice, Poland
Artur RUSOWICZ – Warsaw University of Technology, Poland
Benjamin SCHLEICH – Friedrich-Alexander-Universität Erlangen-Nürnberg, Germany
Jerzy SĘK – Lodz University of Technology, Poland
Reza SERAJIAN – University of California, Merced, USA
Artem SHAKLEIN – Udmurt Federal Research Center, Izhevsk, Russia
G.L. SHI – Guangxi University of Science and Technology, Liuzhou, China
Muhammad Faheem SIDDIQUI – Vrije University, Brussels, Belgium
Jarosław SMOCZEK – AGH University of Science and Technology, Cracow, Poland
Josip STJEPANDIC – PROSTEP AG, Darmstadt, Germany
Pavel A. STRIZHAK – Tomsk Polytechnic University, Russia
Vadym STUPNYTSKYY – Lviv Polytechnic National University, Ukraine
Miklós SZAKÁLL – Johannes Gutenberg-Universität Mainz, Germany
Agnieszka TOMASZEWSKA – Gdansk University of Technology, Poland
Artur TYLISZCZAK – Czestochowa University of Technology, Poland
Aneta USTRZYCKA – Institute of Fundamental Technological Research, Warsaw, Poland
Alper UYSAL – Yildiz Technical University, Turkey
Gabriel WĘCEL – Silesian University of Technology, Gliwice, Poland
Marek WĘGLOWSKI – Welding Institute, Gliwice, Poland
Frank WILL – Technische Universität Dresden, Germany
Michał WODTKE – Gdańsk University of Technology, Poland
Marek WOJTYRA – Warsaw University of Technology, Poland
Włodzimierz WRÓBLEWSKI – Silesian University of Technology, Gliwice, Poland
Hongtao WU – Nanjing University of Aeronautics and Astronautics, China
Jinyang XU – Shanghai Jiao Tong University, China
Zhiwu XU – Harbin Institute of Technology, China
Zbigniew ZAPAŁOWICZ – West Pomeranian University of Technology, Szczecin, Poland
Zdzislaw ZATORSKI – Polish Naval Academy, Gdynia, Poland
Wanming ZHAI – Southwest Jiaotong University, Chengdu, China
Xin ZHANG – Wenzhou University of Technology, China
Su ZHAO – Ningbo Institute of Materials Technology and Engineering, China

This page uses 'cookies'. Learn more