Applied sciences

Archives of Environmental Protection


Archives of Environmental Protection | 2015 | vol. 41 | No 4 |

Download PDF Download RIS Download Bibtex


Presented study aimed to determine metals distribution on the quartz fiber filters surface coated with particulate matter by using high and low-volume samplers. The distribution pattern was tested using two different sub-sampling schemes. Each sub-sample was mineralized in the nitric acid in a microwave oven. An analysis was performed by means of atomic absorption spectroscopy with electrothermal atomization GF-AAS technique, and the determined elements were: As, Cd, Pb and Ni. A validation of the analytical procedure was carried out using NIES 28 Urban Aerosols standard reference material.

It was assumed that metal is distributed uniformly if its normalized concentrations on a single sub-sample is within ±15% of the mean concentration over the whole filter. The normalized concentrations values exceed this range, indicating a non-homogenous metals distribution. There were no statistically significant differences in metals concentrations between particular sub-samples in the function of its position along the filters diameter.

Go to article

Authors and Affiliations

Kamila Widziewicz
Wioletta Rogula-Kozłowska
Krzysztof Loska
Download PDF Download RIS Download Bibtex


People spend most of their time in indoor environments and, consequently, these environments are more significant for the contribution of the daily pollutant exposure than outdoors. In case of children, a great part of their time is spent at school. Therefore, evaluations of this microenvironment are important to assess their time-weighted exposure to air pollutants.

The aim of this study was to assess the children exposure to bioaerosols at schools from two different types of areas, urban and rural. A methodology based upon passive sampling was applied to evaluate fungi, bacteria and pollens, simultaneously with active sampling for fungi and bacterial assessment. Results showed very good correlations between sampling methods, especially for summer season. Passive sampling methodologies presented advantages such as no need of specific and expensive equipment, and they allow achieving important qualitative information.

The study was conducted in different periods of the year to study the seasonal variation of the bioaerosols. Fungi and pollen presented higher levels during the summer time whereas bacteria did not present a seasonal variation. Indoor to outdoor ratios were determined to assess the level of outdoor contamination upon the indoor environment. Levels of fungi were higher outdoor and bacteria presented higher concentrations indoors.

Indoor levels of bioaerosols were assessed in primary schools of urban and rural areas, using the active method along with a passive sampling method. Very good correlations between methods were found which allow the use of the passive sampling method to supply important and reliable qualitative information of bioaerosols concentrations in indoor environments. Seasonal variation in bioaerosols concentrations were found for fungi and pollen. Concentrations of fungi and bacteria above AMV (Acceptable Maximum Value) were found for most of the studied classrooms showing the importance of this microenvironment for the high exposure of children to bioaerosols.

Go to article

Authors and Affiliations

Nuno Canha
Susana Marta Almeida
Maria do Carmo Freitas
Hubert Th. Wolterbeek
Download PDF Download RIS Download Bibtex


Antibiotics are a group of substances potentially harmful to the environment. They can play a role in bacterial resistance transfer among pathogenic and non-pathogenic bacteria. In this experiment three representatives of medically important chemotherapeutics, confirmed to be present in high concentrations in wastewater treatment plants with HPLC analysis were used: erythromycin, sulfamethoxazole and trimethoprim. Erythromycin concentration in activated sludge was not higher than 20 ng L−1. N-acetylo-sulfamethoxazole concentration was 3349 ± 719 in winter and 2933 ± 429 ng L−1 in summer. Trimethoprim was present in wastewater at concentrations 400 ± 22 and 364 ± 60 ng L−1, respectively in winter and summer. Due to a wide variety of PCR-detectable resistance mechanisms towards these substances, the most common found in literature was chosen. For erythromycin: erm and mef genes, for sulfamethoxazole: sul1, sul2, sul3 genes, in the case of trimethoprim resistance dhfrA1 and dhfr14 were used in this study. The presence of resistance genes were analyzed in pure strains isolated from activated sludge and in the activated sludge sample itself. The research revealed that the value of minimal inhibitory concentration (MIC) did not correspond with the expected presence of more than one resistance mechanisms. Most of the isolates possessed only one of the genes responsible for a particular chemotherapeutic resistance. It was confirmed that it is possible to monitor the presence of resistance genes directly in activated sludge using PCR. Due to the limited isolates number used in the experiment these results should be regarded as preliminary.

Go to article

Authors and Affiliations

Aleksandra Ziembińska-Buczyńska
Ewa Felis
Justyna Folkert
Anna Meresta
Dominika Stawicka
Anna Gnida
Joanna Surmacz-Górska
Download PDF Download RIS Download Bibtex


Dye wastewater is one of typically non-biodegradable industrial effluents. A new process linking Fenton’s oxidation with biological oxidation proposed in this study was investigated to degrade the organic substances from real dye wastewater. During the combination process, the Fenton’s oxidation process can reduce the organic load and enhance biodegradability of dye wastewater, which is followed by biological aerated filter (BAF) system to further remove organic substances in terms of discharge requirement. The results showed that 97.6% of chemical oxygen demand (COD) removal by the combination process was achieved at the optimum process parameters: pH of 3.5, H2O2 of 2.0 mL/L, Fe(II) of 500 mg/L, 2.0 h treatment time in the Fenton’s oxidation process and hydraulic retention time (HRT) of 5 h in the BAF system. Under these conditions, COD concentration of effluent was 72.6 mg/L whereas 3020 mg/L in the influent, thus meeting the requirement of treated dye wastewater discharge performed by Chinese government (less than 100 mg/L). These results obtained here suggest that the new process combining Fenton’s oxidation with biological oxidation may provide an economical and effective alternative for treatment of non-biodegradable industrial wastewater.

Go to article

Authors and Affiliations

Haiming Zou
Wanzheng Ma
Yan Wang
Download PDF Download RIS Download Bibtex


This study investigates the influence of four imidazolium ionic liquids (ILs) present in wastewater on the activated sludge process. In addition, experiments with inactivated sludge to assess the capacity of this sorbent to remove ILs from the wastewater were conducted. It occurred that the presence of ionic liquids in wastewater reduces biomass growth and size of the sludge flocs. The strongest effect has been found for IL 6 (1-hexyl-2H-3-methyl-4,5-dimethylimidazolium iodide) with the longest alkyl chain length. Also, the degree of ILs removal increases with the alkyl chain length and decreases with the increase of initial concentration of ILs in wastewater. IL 6 reaches the highest degree of ILs removal from wastewater but inhibits the biomass growth and growth of sludge flocs in a greater extent than other tested compounds. Moreover, it was confirmed that newly synthesized ionic liquids can be adsorbed onto inactivated sludge. IL 6 could be adsorbed in a higher degree than other ionic liquids. This adsorption was described by Langmuir isotherm, whereas adsorption of other ionic liquids was described by Freundlich isotherm.

Go to article

Authors and Affiliations

Dorota Gendaszewska
Ewa Liwarska-Bizukojć
Cedric Maton
Christian V. Stevens
Download PDF Download RIS Download Bibtex


The presented paper reports data from malacological and pedological studies carried out at sites representing diverse biotopes (beech wood, coniferous forest, and meadow) located 2 km away from the Dyckerhoff Cement Plant in Sitkówka-Nowiny in 1992 and in 2008–2009. The studies aimed to determine physicochemical properties of soils exposed to cement and limestone dust emission and to identify composition of snail communities inhabiting three different biotopes in relation to physicochemical properties of soils, and to grasp the dynamics of the alkalization-dependent changes in physicochemical properties of soils and their impact on the composition and ecological structure of malacofauna.

Go to article

Authors and Affiliations

Jadwiga Anna Barga-Więcławska
Anna Świercz
Download PDF Download RIS Download Bibtex


In this study, solidification/stabilization (S/S) of electric arc furnace dust (EAFD) which is generated during the production of steel from scrap metals and classified as hazardous waste were investigated by using different ratios of cement and low grade MgO (LG MgO) as binding agents. Type I PC 42.5 R portland cement and LG MgO which contains 70–80% MgO were used. S/S blocks that contain different ratios of binding agents which have 1/0.5 – 1/1 – 1/2 – 1/3 – 1/4 – 1/5 cement/LG MgO ratio and S/S blocks which contain only cement and no LG MgO agents were prepared. These blocks, which contain 3 different waste ratios according to weight, 20%, 30% and 40% respectively, were produced and exposed to 28-day water purification. At the end of the purification process, S/S blocks were extracted using TCLP (Toxicity Characteristic Leaching Procedure) tests in order to determine the leaching behavior of Zn, Pb, and Cd in S/S blocks. By the end of this study, it was concluded that the recovery of EAFD is possible and applicable by immobilization. The findings of the study concluded that environmental performances or structural properties of blocks contain 30% waste by weight are suitable. This method is a proper one for recovering and treatment of EAFD with mixture of cement and LG MgO.

Go to article

Authors and Affiliations

Ahmet Can Bayraktar
Edip r Avşa
İsmail Toröz
Kadir Alp
Asude Hanedar
Download PDF Download RIS Download Bibtex


Sediments of two dam reservoirs in SE Poland, Zalew Zemborzycki (ZZ) and Brody Iłżeckie (BI) were studied. The sediments from both reservoirs were sampled in the transects perpendicular to the shoreline, at the river inflow and the frontal dam. The total concentration of Mn, Zn, Pb, Cd, Cu, Cr and Ni was determined by ICP-EAS method after the sample digestion in the mixture of concentrated HNO3 and HClO4 acids. The statistical analyses: value intervals, mean values, variation coefficient, the median and the skewed distribution were performed. To estimate differences between the means for transects, Tukey’s test was applied with least significant difference (LSD) determination. The maps of the metal spatial distribution were drawn and sediment quality according to the geochemical and ecotoxicological criteria evaluated. Differences between the reservoirs in terms of heavy metals concentration in bottom sediments, and regularities in their spatial distribution were found. In the ZZ sediments the concentration was at the level of geochemical background (Zn, Cr), slightly (Cd, Cu, Ni) or moderately (Pb) contaminated sediments. The metal concentration in the sediments of the BI was up to eight times higher as compared to the ZZ. Moreover, sediments from the BI reservoir showed a greater variability of metal concentration than those from ZZ, which resulted from the dredging operation performed in the part of the reservoir. Metal concentration in sediments of the dredged part was ca. 2–5 times lower than in the undredged one, which indicates that after the dredging operation, accumulation of these metals was slight. The concentrations of Zn, Pb and Cd from the undredged part of BI were at the level of contaminated sediments and exceeded the probable effects level (PEL). In the ZZ, the greatest accumulation of metals occurred in the upper part of the reservoir and at the frontal dam, and the lowest in the middle part of the reservoir. In BI, the lower outflow of water in this reservoir caused a lower metal concentration in the sediments at the frontal dam, as compared with the other sediments in the undredged part of the reservoir. The results indicate that in small and shallow reservoirs, areas of accumulation of heavy metals depend on such factors as a parent river current, reservoir depth, water waving, reservoir shape (narrowing, coves/bays), and type of water outflow.

Go to article

Authors and Affiliations

Halina Smal
Sławomir Ligęza
Anna Wójcikowska-Kapusta
Stanisław Baran
Danuta Urban
Radomir Obroślak
Artur Pawłowski
Download PDF Download RIS Download Bibtex


The study was conducted on the Biała Lądecka River which is a mountain river. It is similar to many European mountain rivers in terms of hydromorphology and catchment management. The aim of this study was to determine the bioconcentration factors of heavy metals (Pb, Cd, Hg, Ni, Cr, Cu and Zn) in Ranunculus aquatile (L.) Dumort., Fontinalis antipyretica (L. ex Hedw.), and Lemanea fluviatilis (L.) C.Ag. The content of metals in water, sediment, and submerged plants was determined. The metal concentrations in plants can be arranged as follows: Hg < Cd < Cr < Ni < Cu < Pb <Zn. The highest concentrations of Hg, Ni, Cr, and Cu were observed in F. antipyretica, but the highest concentrations of Pb, Cd, and Zn were in R. aquatile. L. fluviatilis always contained the least amounts of heavy metals. Bioconcentration factors (BCFs) were lowest in L. fluviatilis and highest in F. antipyretica. Among the analyzed metals, plants accumulated the highest amount of Zn, and the least of Hg. The BCFs for Zn were from 24111 (in L. fluviatilis) to 97574 (in R. aquatile), and BCFs for Hg were from 29 (in L. fluviatilis) to 226 (in F. antipyretica).

Go to article

Authors and Affiliations

Przemysław Pokorny
Joanna Pokorny
Wojciech Dobicki
Magdalena Senze
Monika Kowalska-Góralska
Download PDF Download RIS Download Bibtex


The work is an attempt to assess piped water quality in four counties located in east central Poland. Piped water was analysed for three successive years in each county. Water samples were tested for the following physical and chemical parameters: turbidity, colour, conductivity, taste, odour, pH, nitrates (III), nitrates (V), iron and manganese. They were compared with the current standard values. Preliminary data analysis included an analysis of maximum and minimum values of physical and chemical parameters, and it revealed that turbidity, colour, iron and manganese contents exceeded the permissible standards in all the counties. Percentages of parameters exceedances and mean values of the exceedances were used to rank the counties in terms of water quality. The ranking was obtained by means of multidimensional comparative analysis. It was demonstrated that best quality water was supplied by Węgrów County water supply system which was followed by Mińsk Mazowiecki County. The third rank was assigned to Łosice County and the poorest quality water was found to be supplied by Siedlce County water supply system.

Go to article

Authors and Affiliations

Elżbieta Radzka
Katarzyna Rymuza
Jolanta Jankowska
Download PDF Download RIS Download Bibtex


The aim of this article is to evaluate the quality of the Danube River in its course through Serbia as well as to demonstrate the possibilities for using three statistical methods: Principal Component Analysis (PCA), Factor Analysis (FA) and Cluster Analysis (CA) in the surface water quality management. Given that the Danube is an important trans-boundary river, thorough water quality monitoring by sampling at different distances during shorter and longer periods of time is not only ecological, but also a political issue. Monitoring was carried out at monthly intervals from January to December 2011, at 17 sampling sites. The obtained data set was treated by multivariate techniques in order, firstly, to identify the similarities and differences between sampling periods and locations, secondly, to recognize variables that affect the temporal and spatial water quality changes and thirdly, to present the anthropogenic impact on water quality parameters.

Go to article

Authors and Affiliations

Danijela Voza
Milovan Vukovic
Ljiljana Takic
Djordje Nikolic
Ivana Mladenovic-Ranisavljevic
Download PDF Download RIS Download Bibtex


Heavy metal pollution of soil is a significant environmental problem and has a negative impact on human health and agriculture. Phytoremediation can be an alternative environmental treatment technology, using the natural ability of plants to take up and accumulate pollutants or transform them. Proper development of plants in contaminated areas (e.g. heavy metals) requires them to generate the appropriate protective mechanisms against the toxic effects of these pollutants. This paper presents an overview of the physiological mechanisms of stress avoidance and tolerance by plants used in phytoremediation of heavy metals.

Go to article

Authors and Affiliations

Anna Małachowska-Jutsz
Anna Gnida

Instructions for authors

Archives of Environmental Protection

Instructions for Authors

Archives of Environmental Protection is a quarterly published jointly by the Institute of Environmental Engineering of the Polish Academy of Sciences and the Committee of Environmental Engineering of the Polish Academy of Sciences. Thanks to the cooperation with outstanding scientists from all over the world we are able to provide our readers with carefully selected, most interesting and most valuable texts, presenting the latest state of research in the field of engineering and environmental protection.

The Journal principally accepts for publication original research papers covering such topics as:
- Air quality, air pollution prevention and treatment;
- Wastewater treatment technologies and processing of sewage sludge;
- Technologies in waste management in the field of neutralization / recovery / closed circulation;
- Hydrology and water quality, water treatment;
- Soil protection and remediation;
- Transformations and transport of organic/inorganic pollutants in the environment;
- Measurement techniques used in environmental engineering and monitoring;
- Other topics directly related to environmental engineering and environment protection.

The Journal accepts also authoritative and critical reviews of the current state of knowledge in the topic directly relating to the environment protection.

If unsure whether the article is within the scope of the Journal, please send an abstract via e-mail to:

Preparation of the manuscript
The following are the requirements for manuscripts submitted for publication:
* The manuscript (with illustrations, tables, abstract and references) should not exceed 20 pages. In case the manuscript exceeds the required number of pages, we suggest contacting the Editor.
* The manuscript should be written in good English.
* The manuscript ought to be submitted in doc or docx format in three files:
– text.doc – file containing the entire text, without title, keywords, authors names and affiliations, and without tables and figures;
– figures.doc
– file containing illustrations with legends;
– tables.doc
– file containing tables with legends;

*The text should be prepared in A4 format, 2.5 cm margins, 1.5 spaced, preferably using Time New Roman font, 12 point. The text should be divided into sections and subsections according to general rules of manuscript editing. The proposed place of tables and figures insertion should be marked in the text.
* Legends in the figures should be concise and legible, using a proper font size so as to maintain their legibility after decreasing the font size. Please avoid using descriptions in figures, these should be used in legends or in the text of the article. Figures should be placed without the box. Legends should be placed under the figure and also without box.
* Tables should always be divided into columns. When there are many results presented in the table it should also be divided into lines.
* References should be cited in the text of an article by providing the name and publication year in brackets, e.g. (Nowak 2019). When a cited paper has two authors, both surnames connected with the word “and” should be provided, e.g. (Nowak and Kowalski 2019). When a cited paper has more than two authors, surname of its first author, abbreviation ‘et al.’ and publication year should be provided, e.g. (Kowalski et al. 2019). When there are more than two publications cited in one place they should be divided with a coma, e.g. (Kowalski et al. 2019, Nowak 2019, Nowak and Kowalski 2019). Internet sources should be cited like other texts - providing the name and publication year in brackets.
* The Authors should avoid extensive citations. The number of literature references must not exceed 30 including a maximum of 6 own papers. Only in review articles the number of literature references can exceed 30.
* References should be listed at the end of the article ordered alphabetically by surname of the first author. References should be made according to the following rules:

1. Journal:
Surnames and initials. (publication year). Title of the article, Journal Name, volume, number, pages, DOI.
For example:

Nowak, S.W., Smith, A.J. & Taylor, K.T. (2019). Title of the article, Archives of Environmental Protection, 10, 2, pp. 93–98, DOI: 10.24425/aep.2019.126330

If the article has been assigned DOI, it should be provided and linked with the website on which it is made available.

2. Book:
Surnames and initials. (publication year). Title, Publisher, Place and publishing year.
For example:

Kraszewski, J. & Kinecki, K. (2019). Title of book, Work & Sudies, Zabrze 2019.

3. Edited book:
Surnames and initials of text authors. (publishing year). Title of cited chapter, in: Title of the book, Surnames and initials of editor(s). (Ed.)/(Eds.). Publisher, Place, pages.
For example:
Reynor, J. & Taylor, K.T. (2019). Title of chapter, in: Title of the cited book, Kaźmierski, I. & Jasiński, C. (Eds.). Work & Studies, Zabrze, pp. 145–189.

4. Internet sources:
Surnames and initials or the name of the institution which published the text. (publication year). Title, (website address (accessed on)).
For example:
Kowalski, M. (2018). Title, ( (03.12.2018)).

5. Patents:
Orszulik, E. (2009). Palenisko fluidalne, Patent polski: nr PL20070383311 20070910 z 16 marca 2009. Smith, I.M. (1988). U.S. Patent No. 123,445. Washington, D.C.: U.S. Patent and Trademark Office.

6. Materials published in language other than English:
Titles of cited materials should be translated into English. Information of the language the materials were published in should be provided at the end.

For example:
Nowak, S.W. & Taylor, K.T. (2019). Title of article, Journal Name, 10, 2, pp. 93–98, DOI: 10.24425/aep.2019.126330. (in Polish)

Not more than 30 references should be cited in the original research paper.

Submission of the manuscript
By submitting the manuscript Author(s) warrant(s) that the article has not been previously published and is not under consideration by another journal. Authors claim responsibility and liability for the submitted article. The article is freely available and distributed under the terms of Creative Commons Attribution-ShareAlike 4.0 International Public License (CC BY SA 4.0, https: //, which permits use, distribution and reproduction in any medium provided the article is properly cited, is not used for commercial purposes and no modification or adaptation are made.

© 2021. The Author(s). This is an open-access article distributed under the terms of the Creative Commons Attribution-ShareAlike 4.0 International Public License (CC BY SA 4.0, https://, which permits use, distribution, and reproduction in any medium, provided that the article is properly cited, the use is non-commercial, and no modifications or adaptations are made

The manuscripts should be submitted on-line using the Editorial System available at Authors are asked to propose at least 4 potential reviewers, including 2 from Poland, together with their e-mail addresses. The journal does not have article processing charges (APCs) nor article submission charges.

Review Process
All the submitted articles are assessed by the Editorial Board. If positively assessed by at least two editors, Editor in Chief, along with department editors selects two independent reviewers from recognized authorities in the discipline. Reviewers receive a text of the article (without personal data of Authors) and review forms applicable in the journal. Review process usually lasts from 1 to 4 months. Reviewers have access to PUBLONS platform which integrates into Bentus Editorial System and enables adding reviews to their personal profile. After completion of the review process Authors are informed of the results and - if both reviews are positive - asked to correct the text according to reviewers’ comments. Next, the revised work is verified by the editorial staff for factual and editorial content.

Acceptance of the manuscript
The manuscript is accepted for publication on grounds of the opinions of independent reviewers and approval of Editorial Board. Authors are informed about the decision and also asked to pay processing charges and to send completed declaration of the transfer of copyright to the editorial office.

Proofreading and Author Correction
All articles published in the Archives of Environmental Protection go through professional proofreading process. If there are too many language errors that prevent understanding of the text, the article is sent back to Authors with a request to correct the indicated fragments or - in extreme cases – to re-translate the text. After proofreading the manuscript is prepared for publishing. The final stage of the publishing process is Author correction. Authors receive a page proof copy of the article with a request to make final corrections.

Article publication charges
The publication fee of an article in the Journal is:
* 20 EUR/80 zł per page (black and white or in gray scale),
* 30 EUR/120 zł per page (color).

Payments in Polish zlotys
Bank BGK
Account no.: 20 1130 1091 0003 9111 7820 0001

Payments in Euros
Bank BGK
Account no.: 20 1130 1091 0003 9111 7820 0001
IBAN: PL 20 1130 1091 0003 9111 7820 0001

Authors are kindly requested to inform the editorial office of making payment for the publication, as well as to send all necessary data for issuing an invoice.

Additional info

Abstracting & Indexing

Archives of Environmental Protection is covered by the following services:

AGRICOLA (National Agricultural Library)



Baidu Scholar


CABI (over 50 subsections)

Chemical Abstracts Service (CAS) - CAplus

Chemical Abstracts Service (CAS) - SciFinder

CNKI Scholar (China National Knowledge Infrastructure)



DOAJ (Directory of Open Access Journals)

EBSCO (relevant databases)

EBSCO Discovery Service

Engineering Village

FSTA - Food Science & Technology Abstracts

Genamics JournalSeek



Google Scholar

Index Copernicus


Japan Science and Technology Agency (JST)


Journal Citation Reports/Science Edition


KESLI-NDSL (Korean National Discovery for Science Leaders)

Microsoft Academic

Naviga (Softweco)

Primo Central (ExLibris)

ProQuest (relevant databases)






Summon (Serials Solutions/ProQuest)


TEMA Technik und Management

Ulrich's Periodicals Directory/ulrichsweb

WanFang Data

Web of Science - Biological Abstracts

Web of Science - BIOSIS Previews

Web of Science - Science Citation Index Expanded

WorldCat (OCLC)

This page uses 'cookies'. Learn more