The article presents a zero-dimensional mathematical model of a tubular fuel cell and its verification on four experiments. Despite the fact that fuel cells are still rarely used in commercial applications, their use has become increasingly more common. Computational Flow Mechanics codes allow to predict basic parameters of a cell such as current, voltage, combustion composition, exhaust temperature, etc. Precise models are particularly important for a complex energy system, where fuel cells cooperate with gas, gas-steam cycles or ORCs and their thermodynamic parameters affect those systems. The proposed model employs extended Nernst equation to determine the fuel cell voltage and steadystate shifting reaction equilibrium to calculate the exhaust composition. Additionally, the reaction of methane reforming and the electrochemical reaction of hydrogen and oxygen have been implemented into the model. The numerical simulation results were compared with available experiment results and the differences, with the exception of the Tomlin experiment, are below 5%. It has been proven that the increase in current density lowers the electrical efficiency of SOFCs, hence fuel cells typically work at low current density, with a corresponding efficiency of 45–50% and with a low emission level (zero emissions in case of hydrogen combustion).
A speaker recognition system based on joint factor analysis (JFA) is proposed to improve whispering speakers’ recognition rate under channel mismatch. The system estimated separately the eigenvoice and the eigenchannel before calculating the corresponding speaker and the channel factors. Finally, a channel-free speaker model was built to describe accurately a speaker using model compensation. The test results from the whispered speech databases obtained under eight different channels showed that the correct recognition rate of a recognition system based on JFA was higher than that of the Gaussian Mixture Model-Universal Background Model. In particular, the recognition rate in cellphone channel tests increased significantly.
The paper deals with multiple soft fault diagnosis of analogue circuits. A method for diagnosis of linear circuits is developed, belonging to the class of the fault verification techniques. The method employs a measurement test performed in the frequency domain, leading to the nonlinear least squares problem. To solve this problem the Powell minimization method is applied. The diagnostic method is adapted to real circumstances, taking into account deviations of fault-free parameters and measurement uncertainty. Two examples of electronic circuits encountered in practice demonstrate that the method is efficient for diagnosis of middle-sized circuits. Although the method is dedicated to linear circuits it can be adapted to multiple soft fault diagnosis of nonlinear ones. It is illustrated by an example of a CMOS circuit designed in a sub-micrometre technology.
According to metrological guidelines and specific legal requirements, every smart electronic electricity meter has to be constantly verified after pre-defined regular time intervals. The problem is that in most cases these pre-defined time intervals are based on some previous experience or empirical knowledge and rarely on scientifically sound data. Since the verification itself is a costly procedure it would be advantageous to put more effort into defining the required verification periods. Therefore, a fixed verification interval, recommended by various internal documents, standardised evaluation procedures and national legislation, could be technically and scientifically more justified and consequently more appropriate and trustworthy for the end user. This paper describes an experiment to determine the effect of alternating temperature and humidity and constant high current on a smart electronic electricity meter’s measurement accuracy. Based on an analysis of these effects it is proposed that the current fixed verification interval could be revised, taking into account also different climatic influence. The findings of this work could influence a new standardized procedure in respect of a meter’s verification interval.
Despite the growing importance of packet switching systems, there is still a shortage of thorough analyses of VoIP transmission effect on speech and speaker recognition performance. Voice over IP transmission systems use packet switching. There is no guarantee of delivery. The main disadvantage of VoIP is a packet loss which has a major impact on the performance experienced by the users of the network. There are several techniques to mask the effects of a packet loss, referred to as packet loss concealment. In this study, the effect of voice transmission over IP on automatic speaker verification system performance was investigated. The analyzed system was based on MAP-EM-GMM modelling methods. Four various speech codecs of H.323 standard were investigated with special emphasis placed on the packet loss phenomenon and various packet loss concealment techniques.
The rigid finite element method (RFEM) has been used mainly for modelling systems with beam-like links. This paper deals with modelling of a single set of electrodes consisting of an upper beam with electrodes, which are shells with complicated shapes, and an anvil beam. Discretisation of the whole system, both the beams and the electrodes, is carried out by means of the rigid finite element method. The results of calculations concerned with free vibrations of the plates are compared with those obtained from a commercial package of the finite element method (FEM), while forced vibrations of the set of electrodes are compared with those obtained by means of the hybrid finite element method (HFEM) and experimental measurements obtained on a special test stand.
Numerical simulation is an economical and effective method in the field of marine engineering. The dynamics of mooring cables has been analysed by a numerical simulation code that was created on a basis of a new element frame. This paper aims at verifying the accuracy of the numerical simulation code through comparisons with both the real experiments and a commercial simulation code. The real experiments are carried out with a catenary chain mooring in a water tank. The experimental results match the simulation results by the numerical simulation code well. Additionally, a virtual simulation of a large size chain mooring in ocean is carried out by both the numerical simulation code and a commercial simulation code. The simulation results by the numerical simulation code match those by the commercial simulation code well. Thus, the accuracy of the numerical simulation code for underwater chain mooring is verified by both the real experiments and commercial simulation code.
On the basis of mathematical modeling of fluid flow in vortex devices verification of use of detached-eddy simulation method in the swirling flows in vortex chamber superchargers is made. Research of a flow with use of different turbulence models was made for vortex chamber supercharger in two working points of the characteristic: with the open exit channel and closed. Verification has been spent on integrated parameters, and also on kinematic, by comparison of static pressure value of on the top end cover of the device. It is received that the hybrid turbulence model DES does not allow, as well as model SST precisely to predict value of vacuum on an axis of the vortex chamber. The error makes an order of 20 %. However, DES predicts almost correct, on 20 % big, than model SST, values of vacuum on an axis in a throat axial diffuser on an input in the vortex chamber. Besides, by means of DES it is possible to describe more adequately unsteady structures near to an axis of the vortex chamber, and also vortex core precession that does not allow to make SST turbulence model. By optimization of vortex devices, and vortex chamber superchargers in particular, simulation time essentially is better to use SST turbulence model with rotation-curvature correction.