Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 6
items per page: 25 50 75
Sort by:

Abstract

A metrological verification of a high precision digital multimeter was made by the laboratory of calibration of programmable electrical multifunction instruments of the National Institute of Metrological Research (INRIM) in order to verify its accuracy and stability. The instrument had been tested for a period of six months for five low-frequency electrical quantities (DC and AC Voltage and Current and DC Resistance). Its stability and precision were compared with the accuracy specifications of the manufacturer. As a new approach, a performance index of the DMM was introduced and evaluated for each examined measurement point. The DMM showed a satisfactory agreement with its specifications to be considered at the level of other top-class DMMs and even better in some measurements points.
Go to article

Abstract

The main focus of this paper is to propose a method for prioritizing knowledge and technology factor of firms towards sustainable competitive advantage. The data has been gathered and analyzed from two high tech start-ups in which technology and knowledge play major role in company’s success. The analytical hierarchy model (AHP) is used to determine competitive priorities of the firms. Then knowledge and technology part of sense and respond questionnaire is used to calculate the variability coefficient i.e. the uncertainty caused by technology and knowledge factor. The proposed model is tested in terms of two start-ups. Based on the initial calculation of uncertainties, some improvement plan is proposed and the method is applied again to see if the uncertainty of knowledge and technology decreases. In both cases, the proposed model helped to have a clear and precise improvement plan and led in reduction of uncertainty.
Go to article

Abstract

This paper presents a robust control technique for small-scale unmanned helicopters to track predefined trajectories (velocities and heading) in the presence of bounded external disturbances. The controller design is based on the linearized state-space model of the helicopter. The multivariable dynamics of the helicopter is divided into two subsystems, longitudinallateral and heading-heave dynamics respectively. There is no strong coupling between these two subsystems and independent controllers are designed for each subsystem. The external disturbances and model mismatch in the longitudinal-lateral subsystem are present in all (matched and mismatched) channels. This model mismatch and external disturbances are estimated as lumped disturbances using extended disturbance observer and an extended disturbance observer based sliding mode controller is designed for it to counter the effect of these disturbances. In the case of heading-heave subsystem, external disturbances and model mismatch only occur in matched channels so a second order sliding mode controller is designed for it as it is insensitive to matched uncertainties. The control performance is successfully tested in Simulink.
Go to article

Abstract

The aim of the article is to present the issue of risk and related management methods, with a particular emphasis on the conditions of investment in energy infrastructure. The work consists of two main parts; the first one is the theoretical analysis of the issue, while the second discusses the application of analysis methods on the example of the investment in an agricultural biogas plant. The article presents the definitions related to the investment risk and its management, with a particular emphasis on the distinction between the risk and uncertainty. In addition, the main risk groups of the energy sector were subjected to an analysis. Then, the basic systematics and the division into particular risk groups were presented and the impact of the diversification of investments in the portfolio on the general level of risk was determined. The sources of uncertainty were discussed with particular attention to the categories of energy investments. The next part of the article presents risk mitigation methods that are part of the integrated risk management process and describes the basic methods supporting the quantification of the risk level and its effects – including the Monte Carlo (MC), Value at risk (VaR), and other methods. Finally, the paper presents the possible application of the methods presented in the theoretical part. The investment in agricultural biogas plant, due to the predictable operation accompanied by an extremely complicated and long-term investment process, was the subject of the analysis. An example of “large drawing analysis” was presented, followed by a Monte Carlo simulation and a VaR value determination. The presented study allows for determining the risk in the case of deviation of financial flows from the assumed values in particular periods and helps in determining the effects of such deviations. The conducted analysis indicates a low investment risk and suggests the ease of similar calculations for other investments.
Go to article

Abstract

The paper addresses the problem of constrained pole placement in discrete-time linear systems. The design conditions are outlined in terms of linear matrix inequalities for the Dstable ellipse region in the complex Z plain. In addition, it is demonstrated that the D-stable circle region formulation is the special case of by this way formulated and solved pole placement problem. The proposed principle is enhanced for discrete-lime linear systems with polytopic uncertainties.
Go to article

Abstract

High distribution system power-losses are predominantly due to lack of investments in R&D for improving the efficiency of the system and improper planning during installation. Outcomes of this are un-designed extensions of the distributing power lines, the burden on the system components like transformers and overhead (OH) lines/conductors and deficient reactive power supply leading to drop in a system voltage. Distributed generation affects the line power flow and voltage levels on the system equipment. These impacts of distributed generation (DG) may be to improve system efficiency or reduce it depending on the operating environment/conditions of the distribution system and allocation of capacitors. For this purpose, allocating of distributed generation optimally for a given radial distribution system can be useful for the system outlining and improve efficiency. In this paper, a new method is used for optimally allocating the DG units in the radial distribution system to curtail distribution system losses and improve voltage profile. Also, the variation in active power load in the system is considered for effective utilization of DG units. To evidence the effectiveness of the proposed algorithm, computer simulations are carried out in MATLAB software on the IEEE-33 bus system and Vastare practical 116 bus system.
Go to article

This page uses 'cookies'. Learn more