This study aims to design a novel air cleaning facility which conforms to the current situation in China, and moreover can satisfy our demand on air purification under the condition of poor air quality, as well as discuss the development means of a prototype product. Air conditions in the operating room of a hospital were measured as the research subject of this study. First, a suitable turbulence model and boundary conditions were selected and computational fluid dynamics (CFD) software was used to simulate indoor air distribution. The analysis and comparison of the simulation results suggested that increasing the area of air supply outlets and the number of return air inlets would not only increase the area of unidirectional flow region in main flow region, but also avoid an indoor vortex and turbulivity of the operating area. Based on the summary of heat and humidity management methods, the system operation mode and relevant parameter technologies as well as the characteristics of the thermal-humidity load of the operating room were analyzed and compiled. According to the load value and parameters of indoor design obtained after our calculations, the airflow distribution of purifying the air-conditioning system in a clean operating room was designed and checked. The research results suggested that the application of a secondary return air system in the summer could reduce energy consumption and be consistent with the concept of primary humidity control. This study analyzed the feasibility and energy conservation properties of cleaning air-conditioning technology in operating rooms, proposed some solutions to the problem, and performed a feasible simulation, which provides a reference for practical engineering.
The article presents the possibility of using the Cobb-Douglas production function for planning in a turbulent environment. A case study was carried out – the Cobb-Douglas function was used to examine the condition of the Polish hard coal mining industry and the progress which has been made after undertaking certain activities aimed at increasing the competitiveness of coal companies over recent years. Only the correct and confirmed identification of the causes of irregularities in the production process can allow for the introduction of effective remedies. The effectiveness of the solutions proposed by the author has been confirmed thanks to the simulation during which the impact of the proposed production strategy on the parameters of the CD function was examined. Three variants of production functions models were created and production productivity rates and marginal substitution rates were determined. The results enabled the verification of the progress of restructuring as well as identification of the origin of the observed problems and comparison of the current state with the results of analyses carried out in previous years. Scenarios of possible trend developments for the factors introduced into the function model in order to present remedial measures that could improve the process of hard coal extraction were created. The scenarios were created using the ARIMA class models. Which scenario is the most favourable was determined. A computer program, created by the author, for optimising the level and use of labor resources at the level of the entire coal company has been presented.
In the paper, the authors discuss the construction of a model of an exemplary urban layout. Numerical simulation has been performed by means of a commercial software Fluent using two different turbulence models: the popular k-ε realizable one, and the Reynolds Stress Model (RSM), which is still being developed. The former is a 2-equations model, while the latter – is a RSM model – that consists of 7 equations. The studies have shown that, in this specific case, a more complex model of turbulence is not necessary. The results obtained with this model are not more accurate than the ones obtained using the RKE model. The model, scale 1:400, was tested in a wind tunnel. The pressure measurement near buildings, oil visualization and scour technique were undertaken and described accordingly. Measurements gave the quantitative and qualitative information describing the nature of the flow. Finally, the data were compared with the results of the experiments performed. The pressure coefficients resulting from the experiment were compared with the coefficients obtained from the numerical simulation. At the same time velocity maps and streamlines obtained from the calculations were combined with the results of the oil visualisation and scour technique.
On the basis of mathematical modeling of fluid flow in vortex devices verification of use of detached-eddy simulation method in the swirling flows in vortex chamber superchargers is made. Research of a flow with use of different turbulence models was made for vortex chamber supercharger in two working points of the characteristic: with the open exit channel and closed. Verification has been spent on integrated parameters, and also on kinematic, by comparison of static pressure value of on the top end cover of the device. It is received that the hybrid turbulence model DES does not allow, as well as model SST precisely to predict value of vacuum on an axis of the vortex chamber. The error makes an order of 20 %. However, DES predicts almost correct, on 20 % big, than model SST, values of vacuum on an axis in a throat axial diffuser on an input in the vortex chamber. Besides, by means of DES it is possible to describe more adequately unsteady structures near to an axis of the vortex chamber, and also vortex core precession that does not allow to make SST turbulence model. By optimization of vortex devices, and vortex chamber superchargers in particular, simulation time essentially is better to use SST turbulence model with rotation-curvature correction.