Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 6
items per page: 25 50 75
Sort by:

Abstract

This article aims to identify potential risk factors affecting the implementation and synchronisation of surveying and construction works during building and operation of roads. The task was executed on the basis of literature studies and experience. The article is an introduction to the research that has been conducted by the authors on the reasonably precise index of factors which one may deal with during the implementation of facilities of this type. The raised issue is crucial for financial and time reasons, but what is important in the roads construction - also for social ones, as prolonged traffic disruption adversely affects the environment.
Go to article

Abstract

In the paper methods for conducting Road Safety Inspections (SIs) in Italy and Poland are described and compared. The goal of the study is to improve the quality and efficiency of the safety inspections of road network by using low cost equipment (GPS, Tablet, Camera) and specific software. Particular attention was paid to the need for proper calibration of factors, causing traffic safety hazard associated with road infrastructure. The model developed according to the Italian procedures was adapted to comply with the checklists and evaluation criteria of the Polish guidelines. Overall, a good agreement between the two approaches was identified, however some modification was required to include new safety issues, characteristic for the Polish network for safety inspection of two lane rural roads. To test the applicability about 100 km of regional two lane roads in Poland were inspected with Polish and Italian procedures.
Go to article

Abstract

U-turn lanes eliminate left turns at intersections and allow the manoeuvre to be made via median crossovers beyond the intersection. However, there are many situations where road infrastructures are characterized by the reduced width of the median. It is clear that, in such situations, we must adopt design criteria that take into account limitations imposed by the width of the cross-section of the road. This is the reason why it is necessary to adopt design solutions which expect a complete reorganization of the road section affected by the insertion of U-turns. In this paper, we intend to propose original guidelines for U-turn lane design, suitable to guarantee both the necessity to offer a high level of functionality of the road sections to be implemented by U-turns, and the principles of safety in order to reduce unsafe conditions during inversion manoeuvres as much as possible.
Go to article

Abstract

The main objective of the research presented in this paper is to enhance driver-passengers comfort of a vehicle that in turn leads to better vehicle safety and stability. The focus was put on studying the interior vibration and noise contributions originated from tire-road and engine-transmission subsystems, due to their significant impact on the dynamic performance of the vehicle. The noise and vibration measurements were recorded at the driver’s head position and on the driver legs room. Furthermore, the influence of different tire types and road surface textures on the vehicle interior noise and vibration were considered. The results indicate that the widely used conventional engine mounts and tires in commercial vehicles cannot fulfill the conflicting requirements for the best isolation concerning both road surface and engine-transmission induced excitations. The values of driver’s head position sound pressure level and floor vibration acceleration broadband averages originate for engine-transmission are lower than that for tire-road interaction. Furthermore, the values of RMS, crest factor, kurtosis and IRI for the vehicle waveform were estimated for vehicle speeds, tire types and road surface textures. Moreover, the percentage contribution for both interior noise and vibration originated from tire-road interaction is higher than the one from vehicle engine-transmission system in all the vehicle speed range, tire type and road surface texture considered.
Go to article

Abstract

The sound radiation from vehicles travelling on the city roads with T junction was considered. The wind effect on acoustic field was taken into account. The solution of this problem was found with the help of the integral Fourier transforms and stationary phase method as the superposition of solutions for the cases of vehicles moving along the straight roads and roads with right-angle bend. As an example, the numerical analysis of traffic noise characteristics was carried out for the T junction city road on one of streets in the town of Łodź (Poland).
Go to article

Abstract

One of the basic parameters which describes road traffic is Annual Average Daily Traffic (AADT). Its accurate determination is possible only on the basis of data from the continuous measurement of traffic. However, such data for most road sections is unavailable, so AADT must be determined on the basis of short periods of random measurements. This article presents different methods of estimating AADT on the basis of daily traffic (VOL), and includes the traditional Factor Approach, developed Regression Models and Artificial Neural Network models. As explanatory variables, quantitative variables (VOL and the share of heavy vehicles) as well as qualitative variables (day of the week, month, level of AADT, the cross-section, road class, nature of the area, spatial linking, region of Poland and the nature of traffic patterns) were used. Based on comparisons of the presented methods, the Factor Approach was identified as the most useful.
Go to article

This page uses 'cookies'. Learn more