Insufficient due planning policy in Poland is subject to widespread and justified criticism. This applies to all levels of spatial management. Legal instruments governing spatial planning in Poland are passive - setting out only the legal framework corresponding to a particular area. They regulate what might be developed within its boundaries, however, they do not specify how it is to be accomplished. Therefore, there is a need to develop an integrated spatial development planning, in which also investors and/or stakeholders would be involved. Apart from answering to the question of what is going to be developed, it will also provide a very comprehensive and flexible implementation strategy having regard to different timelines and local amenities (facilities). This paper also brings an example showing how the spatial planning strategy was conducted for the development of the "Fort Bema" housing estates in the Warsaw district of Bemowo. It highlights the relevance of the planning phase for the subsequent in-use (operating) phase.
The single-phase voltage loss is a common fault. Once the voltage-loss failure occurs, the amount of electrical energy will not be measured, but it is to be calculated so as to protect the interest of the power supplier. Two automatic calculation methods, the power substitution and the voltage substitution, are introduced in this paper. Considering the lack of quantitative analysis of the calculation error of the voltage substitution method, the grid traversal method and MATLAB tool are applied to solve the problem. The theoretical analysis indicates that the calculation error is closely related to the voltage unbalance factor and the power factor, and the maximum calculation error is about 6% when the power system operates normally. To verify the theoretical analysis, two three-phase electrical energy metering devices have been developed, and verification tests have been carried out in both the lab and field conditions. The lab testing results are consistent with the theoretical ones, and the field testing results show that the calculation errors are generally below 0.2%, that is correct in most cases.
In this article, we study tilted fiber Bragg gratings (TFBGs) with tilt angles of 6◦ and 8◦, their transmission spectra, and spectral parameters that have a linear dependence on the refractive index of the environment. It is shown that there can be several such characteristics, such as the minimum, width and energy of the spectrum. The linear dependence of the spectrum width on the refractive index does not depend on the tilt angle. The linear dependence of the spectrum minimum is only observed for a tilt angle of 8◦. The results of this work can be used to create a sensor system based on an optical fiber.
In the past it was usual to exert a huge effort in the design, simulation, and the real time implementation of the complicated electronic and communication systems, like GNSS receivers. The complexity of the system algorithms combined with the complexity of the available tools created a system that is difficult to track down for debugging or for redesign. So, the simulation and educational tools was different from the prototyping tools. In this paper the parallel search acquisition phase of a GPS receiver was simulated and implemented on FPGA using the same platform and through a graphical programming language. So this paper introduces the fruit of integrating the prototyping tools with the simulation tools as a single platform through which the complicated electronic systems can be simulated and prototyped.
In order to determine the leading phase of the Fe - 4.25% C eutectic alloy, the method of directional crystallization, which allows to study the character of the solid / liquid growth front, was used. Examined eutectic was directionally solidified with a constant temperature gradient of G = 33,5 K/mm and growth rate of v = 125 μm/s (450 mm/h). The Bridgman technique was used for the solidification process. The sample was grown by pulling it downwards up to 30 mm in length. The alloy quenched by rapid pulling down into the Ga-In-Sn liquid metal. The sample was examined on the longitudinal section using a light microscope and scanning electron microscope. The shape of the solid/liquid interface and particularly the leading phase protrusion were revealed. The formation of the concave – convex interface has been identified in the quasi-regular eutectic growth arrested by quenching. The cementite phase was determined to be a leading phase. The total protrusion d is marked in the adequate figure.
This paper presents a study of control strategies for 5-phase permanent magnet synchronous motors (PMSMs) supplied by a five-leg voltage source inverter. Based on the vectorial decomposition of the multi-phase machine, fictitious machines, magnetically decoupled, allow a more adequate control. In this paper, our study focuses on the vector control of a multi-phase machine using a linear proportional-integral-derivative (PID) current regulator in the cases of sinusoidal and trapezoidal back-electromotive force (EMF) waveforms. In order to determine currents’ references, two strategies are adopted. First one aims to minimize copper losses under constant torque, while the second one targets to increase torque for a given copper losses. These techniques are tested under a variable speed control strategy based on a proportional-integral (PI) regulator and experimentally validated.
This paper discusses the influence of the direction of applied deformation on the ability to gelation of thermosensitive chitosan hydrogels. The application of the shear rate equal in value to the classically performed oscillatory measurements leads to significantly different shapes of experimental curves. It was found that the type of mechanically applied deformation has a significant impact on the gelation ability of colloidal chitosan solutions and conditions of sol-gel phase transition. Simple shear leads to a phase transition at a lower temperature or in a shorter time compared to oscillatory tests. Moreover, based on the final values of dynamic viscosity in rotational measurements, it was found that stronger crosslinking of the polymer structure was observed.
The Vistulian decline was a period of rapid environmental events. The authors correlated ages of the last Scandinavian Ice Sheet limits in northern Poland with ages of prominent events adapting the conditions of periglacial environment of Central Poland in response to the Late Vistulian climate warming. Ages from previous thematic geological and palaeogeographical studies were collected. The approach used indicates that despite methodological uncertainties and sometimes inconsistency of ages, it is especially helpful in timing of first warming signals (ca. 19–18 cal ka BP) and establishing of environmentally bipartite 3 millennia of the Oldest Dryas in the extraglacial zone. Abrupt warming at the onset of the Bølling-Allerød is well registered in biotic and abiotic archives available from Central Poland and remains in agreement with the large recession of the southern ice sheet margin.
This article deals with the effect of manganese that is the most applied element to eliminate the negative effect of iron in the investigated alloy AlSi7Mg0.3. In this time are several methods that are used for elimination harmful effect of iron. The most used method is elimination by applying the additive elements, so-called iron correctors. The influence of manganese on the morphology of excluded ironbased intermetallic phases was analysed at various iron contents (0.4; 0.8 and 1.2 wt. %). The effect of manganese was assessed in additions of 0.1; 0.2; 0.4 and 0.6 wt. % Mn. The morphology of iron intermetallic phases was assessed using electron microscopy (SEM) and EDX analysis. The increase of iron content in investigated alloys caused the formation of more intermetallic phases and this effect has been more significant with higher concentrations of manganese. The measurements carried out also showed that alloys with the same Mn/Fe ratio can manifest different structures and characteristics of excluded iron-based intermetallic phases, which might, at the same time, be related to different resulting mechanical properties.
The article presents the results of research concerning to AlCu4MgSi alloy ingots produced using horizontal continuous casting process. The presented research was focused on the precise determination of phase composition of the precipitates formed during the solidification of ingots and the analysis of their thermal stability. In order to assess the morphology of precipitates in the AlCu4MgSi alloy, data obtained by using a computer simulation of thermodynamic phenomena were compiled with results obtained using advanced research techniques, i.e. High-temperature X-ray diffraction (HT-XRD), SEM-EDS, Thermal and derivative analysis (TDA) and Glow discharge optical emission spectroscopy (GD OES). SEM observations and analysis of chemical composition in micro-areas showed that the precipitates are mainly intermetallic θ-Al2Cu and β-Mg2Si phases, and also presence of Al19Fe4MnSi2 intermetallic phase was confirmed by X-ray diffraction studies. Based on the prepared Thermo-Calc simulation data, high-temperature X-ray diffraction measurements were conducted.
Fabrication and microstructure of the AlSi11 matrix composite containing 10 % volume fraction of CrFe30C8 particles were presented in this paper. Composite suspension was manufactured by using mechanical stirring. During stirring process the temperature of liquid metal, time of mixing and rotational speed of mixer were fixed. After stirring process composite suspension was gravity cast into shell mould. The composites were cast, applying simultaneously an electromagnetic field. The aim of the present study was to determine the effect of changes in the frequency of the current power inductor on the morphology of the reinforcing phase in the aluminum matrix. The concept is based on the assumption that a chromium-iron matrix of CrFe30C8 particles dissolves and residual carbide phases will substantially strengthen the composite. The microstructure and interface structure of the AlSi11/CrFe30C8 composite has been studied by optical microscopy, scanning microscopy and X-ray diffraction.
The article presents personal memories of Professor Aleksander Koj’s alumni. Professor Aleksander Koj was a world-class biochemist of significant scientific achievements, a renowned authority in the field of acute-phase response regulation and acute-phase proteins. He was an excellent academic, a true Master, admired and followed by many Polish biochemists. Thrice he served as the Rector of the Jagiellonian University in Kraków. He navigated the University through a difficult time of political transformation in Poland, modernized the management system of the University and led to the commencement of the construction of the new University campus. He was the co-creator and the first Chairman of the Conference of Rectors of Academic Schools in Poland. He will be remembered as a devoted community worker aiming at strengthening the bond between the Polish community abroad and our homeland, propagating knowledge, promoting the concept of European integration, democracy and tolerance, as well as the collaboration between scientists, artists and men and women of culture. He was wise, righteous, and noble. Many had the honor of calling him their friend, and a great many saw in him a moral authority.
Effects of confinement on mechanical, structural and thermodynamic properties of uniform fluids are very well understood. In contrast, a general theory based on statistical thermodynamics for confined nonuniform and non-isotropic phases, such as the lamellar phase, is in its infancy. In this review we focus on the lamellar phase confined in a slit or in a pipe in order to illustrate various effects of confinement. We limit ourselves to the results obtained by M. Tasinkevych, V. Babin and the author for lamellar phases in oil-water-surfactant mixtures within a generic semi-microscopic model, using a mean-field approximation. We show that compared to isotropic fluids the excess grand potential contains additional terms associated with structural deformations. These terms depend on the type of the confining walls, the shape of the container and on the thickness of the lamella. As a result of the dependence of the structure of the confined lamellar phase on the shape of the container, capillary lamellarization and capillary delamellarization is found in slits and in pipes respectively.
In the present paper it is proposed to consider the computer cooling capacity using the thermosyphon loop. A closed thermosyphon loop consists of combined two heaters and a cooler connected to each other by tubes. The first heater may be a CPU processor located on the motherboard of the personal computer. The second heater may be a chip of a graphic card placed perpendicular to the motherboard of personal computer. The cooler can be placed above the heaters on the computer chassis. The thermosyphon cooling system on the use of computer can be modeled using the rectangular thermosyphon loop with minichannels heated at the bottom horizontal side and the bottom vertical side and cooled at the upper vertical side. The riser and a downcomer connect these parts. A one-dimensional model of two-phase flow and heat transfer in a closed thermosyphon loop is based on mass, momentum, and energy balances in the evaporators, rising tube, condenser and the falling tube. The separate two-phase flow model is used in calculations. A numerical investigation for the analysis of the mass flux rate and heat transfer coefficient in the steady state has been accomplished.
Horizontal centrifugal casting is an effective method for the production of hollow metal with good mechanical properties, low defect, cast to size and relatively cheap. The ability of a metal to satisfy the above requirements highly depends on its microstructure. In this study, the relationship between microstructural parameters such as grain size and the amount of phases with bulk hardness of SnCu4Pb3 is concerned in three areas of the product. Consequently, to achieve the desired hardness of the product in a particular area, the interaction of two factors of the microstructure including, grain size and particles amount of the hard intermetallic compositions (Cu6Sn5) should be noted.
The paper presents a concept of a control system for a high-frequency three-phase PWM grid-tied converter (3x400 V / 50 Hz) that performs functions of a 10-kW DC power supply with voltage range of 600÷800 V and of a reactive power compensator. Simulation tests (in PLECS) allowed proper selection of semiconductor switches between fast IGBTs and silicon carbide MOSFETs. As the main criterion minimum amount of power losses in semiconductor devices was adopted. Switching frequency of at least 40 kHz was used with the aim of minimizing size of passive filters (chokes, capacitors) both on the AC side and on the DC side. Simulation results have been confirmed in experimental studies of the PWM converter, the power factor of which (inductive and capacitive) could be regulated in range from 0.7 to 1.0 with THDi of line currents below 5% and energy efficiency of approximately 98.5%. The control system was implemented in Texas Instruments TMS320F28377S microcontroller.
Microwave frequency detectors enable immediate determination of an unknown microwave signal frequency. Measurement is possible if the output characteristic of a frequency detector is unequivocal in a selected band of operation. The paper presents a method for obtaining unequivocal output characteristics for a given band of frequency detector operation.
This paper reports the results of research involving observations of flow patterns during air-oil-water three-phase flow through a vertical pipe with an internal diameter of 0.03 m and a length of 3 m. The conductometric method based on the measurement of electrical conductivity of the gas-liquid-liquid system was used to evaluate the flow patterns. In the studies, a set of eight probes spaced concentrically in two tube sections (four probes per each) with a spacing of 0.015 m were used. The paper presents a theoretical description of the test method and the analysis of the measurement results for air-oil-water multiphase flow system. Results of this study indicate that the developed method of characterizing the voltage of the gas-liquid-liquid system can be an important tool supporting other methods to identify flow patterns, including visual observation.
In the paper, a feedforward linearization method for differential-pair operational transconductance ampliﬁer (OTA) is discussed. The proposed technique is developed using simple differential pair transconductors and linear reference resistor. The concept leads not only to very efficient linearization ofa transfer characteristic oft he OTA but also others the possibility of effﬀective phase compensation. Due to this, the circuit can be used in applications requiring precise phase response (e.g. ﬁlters). SPICE simulations show that for the circuit working with a ±1.25V power supply, total harmonic distortion (THD) at 0.8Vpp is less then 0.1% in comparison to 10.2% without linearization. Moreover, the input voltage range ofline ar operation is increased. Power consumption oft he overall circuit is 0.94mW. The 3rd order elliptic ﬁlter example has been designed and simulated. It turns out that the proposed compensation scheme signiﬁcantly improves the performance of the ﬁlter at higher frequencies.
Although the phenomenon of otoacoustic emission has been known for nearly 30 years, it has not been fully explained yet. One kind of otoacoustic emission is distortion product of the otoacoustic emission (DPOAE). New aspects of this phenomenon are constantly discovered and attempts are made to interpret correctly the obtained results. This paper discusses a new method of measuring DPOAE signals based on double phase-sensitive detection, which makes possible a real-time measurement of the DPOAE signal amplitude and phase. The method was applied for measurements of DPOAE signals in guinea pigs. Sample records are presented and the obtained results are discussed.
Results of velocity measurements of liquid and gas bubbles in a tank with a self-aspirating disk impeller are analysed. Studies were carried out using a fluorescent dye tracer in the measuring system with two cameras (simultaneous phase velocity measurement) and with one camera (sequential measurement of phase velocity). Based on a comparative analysis of the acquired data it was found that when differences in the phase velocities were small the simultaneous velocity measurement gave good results. However, sequential measurement gives greater possibilities for setting the measuring system and if the analysis of instantaneous velocities is not necessary, it seems to be a better solution.
The study presents the possible use of optoelectronic system for the measurement of values specific for hydrodynamics of two-phase gas very-high-viscosity liquid flow in vertical pipes. An experimental method was provided, and the findings were presented and analysed for selected values which characterise the two-phase flow.
In this paper, the deviation from eutectic composition in boundary layer for eutectic growth is studied by phase-field method. According to a series of artificial phase diagram, the lamellar eutectic growth of these alloy is simulated during directional solidification. At steady state, average growth velocity of eutectic lamella is equal to the pulling velocity. With the increasing of the liquidus slope of β phase, the average composition in boundary layer would deviate from eutectic composition and the deviation increases. The constitutional undercooling difference between both solid phases caused by the deviation increases with the increasing of the deviation. The β phase would develop a depression under the influence of the deviation.