Search results

Filters

  • Journals
  • Date

Search results

Number of results: 9
items per page: 25 50 75
Sort by:

Abstract

The results of long-term continuous noise measurements in two selected schools are presented in the paper. Noise characteristics were measured continuously there for approximately 16 months. Measurements started eight months prior to the acoustic treatment of the school corridors of both schools. An evaluation of the acoustic climates in both schools, before and after the acoustic treatment, was performed based on comparison of these two periods of continuous measurements. The autonomous noise monitoring stations, engineered at the Multimedia Systems Department of the Gdańsk University of Technology were used for this purpose. Investigations of measured noise, especially its influence on hearing sense, assessed on ground of spectral analyses in critical bands, is discussed. Effects of occupational noise exposure, including the Temporary Threshold Shift simulation, are determined. The correlation of the above said measurement results with respective instantaneous noise levels is discussed, and concluding remarks are presented. Some additional indicators such as air pollution or video analysis aiming at the analysis of corridor occupancy are also measured. It should be remembered that excessive noise, or air pollution may be evidence of a dangerous event and may pose health risks.
Go to article

Abstract

The paper formulates some objections to the methods of evaluation of uncertainty in noise measurement which are presented in two standards: ISO 9612 (2009) and DIN 45641 (1990). In particular, it focuses on approximation of an equivalent sound level by a function which depends on the arithmetic average of sound levels. Depending on the nature of a random sample the exact value of the equivalent sound level may be significantly different from an approximate one, which might lead to erroneous estimation of the uncertainty of noise indicators. The article presents an analysis of this problem and the adequacy of the solution depending on the type of a random sample.
Go to article

Abstract

Studies of electrical properties, including noise properties, of thick-film resistors prepared from various resistive and conductive materials on LTCC substrates have been described. Experiments have been carried out in the temperature range from 300 K up to 650 K using two methods, i.e. measuring (i) spectra of voltage fluctuations observed on the studied samples and (ii) the current noise index by a standard meter, both at constant temperature and during a temperature sweep with a slow rate. The 1/f noise component caused by resistance fluctuations occurred to be dominant in the entire range of temperature. The dependence of the noise intensity on temperature revealed that a temperature change from 300 K to 650 K causes a rise in magnitude of the noise intensity approximately one order of magnitude. Using the experimental data, the parameters describing noise properties of the used materials have been calculated and compared to the properties of other previously studied thick-film materials.
Go to article

Abstract

A developed method and measurement setup for measurement of noise generated in a supercapacitor is presented. The requirements for noise data recording are considered and correlated with working modes of supercapacitors. An example of results of low-frequency noise measurements in commercially available supercapacitors are presented. The ability of flicker noise measurements suggests that they can be used to assess quality of tested supercapacitors.
Go to article

Abstract

This work is a contribution to a normative approach of noise assessment in the professional environment. It permits the identification of the affected workstations on the one hand and on the other hand it constitutes an important support to the preoccupations of the impact study on the environment in plants. It also informs us on the adequate preparation of the procedures required by the Environmental Management System (ISO 14001) being implemented in steel-making complex ArcelorMittal Algeria. It constitutes an answer to the recommended environmental politics. The proposed calculation methods are verified according to the recognized sources (ISO 9612, 2009) and the results will be estimated in relation to the legal thresholds recommended by international bodies. The methodology for measuring the noise exposure levels has been done according to the following steps: work analysis; selection of measurement strategy; measurements; error handling and uncertainty evaluations; calculations; and presentation of results. This will lead us to an implementation of a corrective and preventive action plan intended to master this occupational risk carrying prejudice to the health of the workers.
Go to article

Abstract

Electrochemical amperometric gas sensors represent a well-established and versatile type of devices with unique features: good sensitivity and stability, short response/recovery times, and low power consumption. These sensors operate at room temperature, and therefore have been applied in monitoring air pollutants and detection of toxic and hazardous gases in a number of areas. Some drawbacks of classical electrochemical sensors are overcome by the solid polymer electrolyte (SPE) based on ionic liquids. This work presents evaluation of an SPE-based amperometric sensor from the point of view of current fluctuations. The sensor is based on a novel three-electrode sensor platform with solid polymer electrolytes containing ionic liquid for detection of nitrogen dioxide − a highly toxic gas that is harmful to the environment and presenting a possible threat to human health even at low concentrations. The paper focuses on using noise measurement (electric current fluctuation measurement) for evaluation of electrochemical sensors which were constructed by different fabrication processes: (i) lift-off and drop-casting technology, (ii) screen printing technology on a ceramic substrate and (iii) screen printing on a flexible substrate.
Go to article

Abstract

The assessment of the uncertainty of measurement results, an essential problem in environmental acoustic investigations, is undertaken in the paper. An attention is drawn to the - usually omitted - problem of the verification of assumptions related to using the classic methods of the confidence intervals estimation, for the controlled measuring quantity. Especially the paper directs attention to the need of the verification of the assumption of the normal distribution of the measuring quantity set, being the base for the existing and binding procedures of the acoustic measurements assessment uncertainty. The essence of the undertaken problem concerns the binding legal and standard acts related to acoustic measurements and recommended in: 'Guide to the expression of uncertainty in measurement' (GUM) (OIML 1993), developed under the aegis of the International Bureau of Measures (BIPM). The model legitimacy of the hypothesis of the normal distribution of the measuring quantity set in acoustic measurements is discussed and supplemented by testing its likelihood on the environment acoustic results. The Jarque-Bery test based on skewness and flattening (curtosis) distribution measures was used for the analysis of results verifying the assumption. This test allows for the simultaneous analysis of the deviation from the normal distribution caused both by its skewness and flattening. The performed experiments concerned analyses of the distribution of sound levels: LD, LE, LN, LDWN, being the basic noise indicators in assessments of the environment acoustic hazards.
Go to article

Abstract

Passive radar does not have its own emitter. It uses so-called signals of opportunity emitted by non-cooperative illuminators. During the detection of reflected signals, a direct signal from a non-cooperative emitter is used as the reference signal. Detection of electromagnetic echoes is, in present day radars, performed by finding the maximum of the cross ambiguity function. This function is based on the multiplication of the received signal and the reference signal. Detection of echoes by means of a quadrature microwave phase discriminator QMPD was proposed in the work as an alternative solution for ambiguity function evaluation. This discriminator carries out vectorial summing of the received and the reference signals. The summing operations in QMPD are carried out with the aid of microwave elements and without the use of expensive digital signal processors. Definitions of the phase and phase difference of the so-called simple signals and noise signals were described. A proposal of a passive radar equipped with several independent quadrature microwave phase discriminators was presented. Ideas of algorithms of object detection and of the distance-to-object estimation designed for this radar have been also sketched.
Go to article

Abstract

An embedded time interval data acquisition system (DAS) is developed for zero power reactor (ZPR) noise experiments. The system is capable of measuring the correlation or probability distribution of a random process. The design is totally implemented on a single Field Programmable Gate Array (FPGA). The architecture is tested on different FPGA platforms with different speed grades and hardware resources. Generic experimental values for time resolution and inter-event dead time of the system are 2.22 ns and 6.67 ns respectively. The DAS can record around 48-bit x 790 kS/s utilizing its built-in fast memory. The system can measure very long time intervals due to its 48-bit timing structure design. As the architecture can work on a typical FPGA, this is a low cost experimental tool and needs little time to be established. In addition, revisions are easily possible through its reprogramming capability. The performance of the system is checked and verified experimentally.
Go to article

This page uses 'cookies'. Learn more