Coal mining activities carried out for 200 years in Upper Silesia have had a negative effect on buildings. T his impact is in all cases related with continuous deformations of the surface and in certain cases with discontinuous deformations (mostly cave-ins), changes in water relations and mining tremors. T he paper presents an evaluation of the impact of a mining activity on a building situated in the Upper Silesian Coal Basin. T he building was affected by continuous deformations and mining tremors. Calculations were made of the values of deformation rates by means of Budryk–Knothe’s theory, which were partly verified on the basis of the results from geodetic measurements. An analysis of the velocity and acceleration of basement vibrations caused by mining-induced tremors was also conducted. T he conclusions included a high consistency between the results obtained on the basis of calculations and the values obtained by means of PGA and PGV measurements. In the case of tremors with the highest energy in the hipocentrum, there an empirical formula allowing for calculation of PGA value in given geological and mining conditions was also proposed. T he application range of the formula mentioned above is obviously limited only to the conditions in consideration. The presented conclusions indicate that at present, sufficiently precise methods, allowing for calculations for practical purposes, not only of deformation indices’ values, but also of PGV and PGA values, presently exist.
The extraction of mineral deposits is usually charged with additional taxes or royalty fees that go beyond the general income tax. As a rule, countries prefer stable sources of fiscal revenues based on the volume of raw material extraction, and investors prefer models based on profit tax, i.e. taking operating costs and risks lower than the expected profitability of the project into account. As a rule, too high a burden for the mining sector affects investors’ decisions regarding the introduction of new investments. There are a number of examples where excessive fiscal burdens force investors to move to countries with more favorable tax systems. An analysis of various forms of taxation of mining enterprises around the world has been presented and compared with the system implemented in Poland. Usually, the countries that apply the royalty fee in the mining sector at the same time introduce a number of adaptation mechanisms. This is crucial for new investments due to the fact that they may to some extent compensate for the high costs of transition from the investment to the operational phase. In most cases, several incentive mechanisms are used at the same time, e.g. the accelerated settlement of investment expenditures and the unlimited settlement of losses. The copper and silver mining tax introduced in Poland increased the discounted effective tax rate (ETR) from 38.5% to 89% for the entire investment period, which resulted in a 11-year return on investment, as well as a drop in the internal rate of return (IRR).There are currently no mechanisms in Poland which would balance the burden of this tax for a new investor. In order to balance the extraction tax for certain minerals in terms of the IRR and ETR key indicators, the introduction of several adaptation mechanisms has been proposed. For new investments the most essential mechanism is the preferential settlement of capital expenditures incurred in the pre-production phase of an investment. The others include accelerated amortization, the ability to deduct certain expenses for the exploration phase from the tax base, along with an extended tax loss settlement period, or a mechanism for deducting a certain percentage of investment expenses directly from the tax.
Underground mining extraction causes the displacement and changes of stress fields in the surrounding rock mass. The determination of the changes is extremely important when the mining activity takes place in the proximity of post-flotation tailing ponds, which may affect the stability of the tailing dams. The deterministic modeling based on principles of continuum mechanics with the use of numerical methods, e.g. finite element method (FEM) should be used in all problems of predicting rock mass displacements and changes of stress field, particularly in cases of complex geology and complex mining methods. The accuracy of FEM solutions depends mainly on the quality of geomechanical parameters of the geological strata. The parameters, e.g. young modulus of elasticity, may require verification through a comparison with measured surface deformations using geodetic methods. This paper presents application of FEM in predicting effects of underground mining on the surface displacements in the area of the KGHM safety pillar of the tailing pond of the OUOW Żelazny Most. The area has been affected by room and pillar mining with roof bending in the years 2008-2016 and will be further exposed to room-and-pillar extraction with hydraulic filling in the years 2017–2019.
Significant quantities of coal sludge are created during the coal enrichment processes in the mechanical processing plants of hard coal mines (waste group 01). These are the smallest grain classes with a grain size below 1 mm, in which the classes below 0.035 mm constitute up to 60% of their composition and the heat of combustion is at the level of 10 MJ/kg. The high moisture of coal sludge is characteristic, which after dewatering on filter presses reaches the value of 16–28% (Wtot r) (archival paper PG SILESIA). The fine-grained nature and high moisture of the material cause great difficulties at the stage of transport, loading and unloading of the material. The paper presents the results of pelletizing (granulating) grinding of coal sludge by itself and the piling of coal sludge with additional material, which is to improve the sludge energy properties. The piling process itself is primarily intended to improve transport possibilities. Initial tests have been undertaken to show changes in parameters by preparing coal sludge mixtures (PG SILESIA) with lignite coal dusts (LEAG). The process of piling sludge and their mixtures on an AGH laboratory vibratory grinder construction was carried out. As a result of the tests, it can be concluded that all mixtures are susceptible to granulation. This process undoubtedly broadens the transport possibilities of the material. The grain composition of the obtained material after granulation is satisfactory. Up to 2 to 20 mm granules make up 90–95% of the product weight. The strength of the fresh pellets is satisfactory and comparable for all mixtures. Fresh lumps subjected to a test for discharges from a height of 700 mm can withstand from 7 to 14 discharges. The strength of the pellets after longer seasoning, from the height of 500 mm, shows different values for the analyzed samples. The values obtained for hard coal sludge and their blends with brown coal dust are at the level from 4 to 5 discharges. The strength obtained is sufficient to determine the possibility of their transport. At this stage of the work it can be stated that the addition of coal dust from lignite does not cause the deterioration of the material’s strength with respect to clean coal sludge. Therefore, there is no negative impact on the transportability of the granulated material. As a result of mixing with coal dusts, it is possible to increase their energy value (Klojzy-Karczmarczyk at al. 2018). The cost analysis of the analyzed project was not carried out.