Search results

Filters

  • Journals
  • Date

Search results

Number of results: 10
items per page: 25 50 75
Sort by:

Abstract

In this paper the capacity of non-uniform sampling rate conversion techniques, involving different interpolation methods, aimed at wow defect reduction, is examined. Involved are: linear interpolation, four polynomial-based interpolation methods and the windowed sincbased method. The examined polynomial methods are: Lagrange interpolation, polynomial fitting with additional noise reduction, Hermitan and Spline. The performance of an artificially distorted audio signal, restored using non-uniform resampling, is evaluated on the basis of standard audio defect measurement criteria and compared for all of the aforementioned interpolation methods. The chosen defect descriptors are: total harmonic distortion, total harmonic distortion plus noise and signal to noise ratio.
Go to article

Abstract

Determination of High Arctic regions bathymetry is strictly dependent from weather and ice mass quantity. Due to safety, it is often necessary to use a small boat to study fjords area, especially close to glaciers with unknown bathymetry. This precludes the use of modern multi−beam echosounders, and so traditional single−beam echosounders have been used for bathymetry profiling. Adequate interpolation techniques were determined for the most probable morphological formations in−between bathymetric profiles. Choosing the most accurate interpolation method allows for the determination of geographical regionalisation of submarine elevations of the Brepollen area (inner part of Hornsund, Spitsbergen). It has also been found that bathymetric interpolations should be performed on averaged grid values, rather than individual records. The Ordinary Kriging Method was identified as the most adequate for interpolations and was compared with multi beam scanning, which was possible to make due to a previously modelled single beam interpolation map. In total, eight geographical units were separated in Brepollen, based on the bathymetry, slope and aspect maps. Presented results provide a truly new image of the area, which allow for further understanding of past and present processes in the High Arctic.
Go to article

Abstract

Dual quaternions and dual quaternion interpolation are powerful mathematical tools for the spatial analysis of rigid body motions. In this paper, after a review of some basic results and formulas, it will be presented an attempt to use these tools for the the kinematic modeling of human joints. In particular, the kinematic parameters extracted from experimentally acquired data are compared with those theoretically computed from dual quaternions rigid body motion interpolation.
Go to article

Abstract

The article shows the methodology and calculation procedures based on Lagrange polynomial interpolation which were used to determine standard performance characteristics of the Polish production engine, type ANDORIA 4CTi90-1BE6. They allow to simplify the experimental research by maintaining a minimum number of measurement points and estimating the remaining data in an analytical way. The methods presented are convenient when it comes to the practical side because they eliminate the need for exploration of mathematical equations describing the various curves, which can be cumbersome and time consuming in the case of nonautomated accounts. The results of analysis were applied to actual experimental results, indicating sufficient accuracy of the resulting approximations. As a result, procedures may be used in bench testing of a similar profile, especially with repeated cycles of the experiment, such as optimization of operating parameters of combustion engines.
Go to article

Abstract

Persistent organic pollutants (POPs) originating from agrochemical industries have become an urgent environmental problem worldwide. Ordinary kriging, as an optimal geostatistical interpolation technique, has been proved to be sufficiently robust for estimating values with finite sampled data in most of the cases. In this study, ordinary kriging interpolation integrate with 3D visualization methods is applied to characterize the monochlorobenzene contaminated soil for an agrochemical industrial site located in Jiangsu province. Based on 944 soil samples collected by Geoprobe 540MT and monitored by SGS environmental monitoring services, 3D visualization in terms of the spatial distribution of pollutants in potentially contaminated soil, the extent and severity of the pollution levels in different layers, high concentration levels and isolines of monochlorobenzene concentrations in this area are provided. From the obtained results, more information taking into account the spatial heterogeneity of soil area will be helpful for decision makers to develop and implement the soil remediation strategy in the future.
Go to article

Abstract

Various sectors of the economy such as transport and renewable energy have shown great interest in sea bed models. The required measurements are usually carried out by ship-based echo sounding, but this method is quite expensive. A relatively new alternative is data obtained by airborne lidar bathymetry. This study investigates the accuracy of these data, which was obtained in the context of the project ‘Investigation on the use of airborne laser bathymetry in hydrographic surveying’. A comparison to multi-beam echo sounding data shows only small differences in the depths values of the data sets. The IHO requirements of the total horizontal and vertical uncertainty for laser data are met. The second goal of this paper is to compare three spatial interpolation methods, namely Inverse Distance Weighting (IDW), Delaunay Triangulation (TIN), and supervised Artificial Neural Networks (ANN), for the generation of sea bed models. The focus of our investigation is on the amount of required sampling points. This is analyzed by manually reducing the data sets. We found that the three techniques have a similar performance almost independently of the amount of sampling data in our test area. However, ANN are more stable when using a very small subset of points.
Go to article

Abstract

The key to fingerprint positioning algorithm is establishing effective fingerprint information database based on different reference nodes of received signal strength indicator (RSSI). Traditional method is to set the location area calibration multiple information sampling points, and collection of a large number sample data what is very time consuming. With Zigbee sensor networks as platform, considering the influence of positioning signal interference, we proposed an improved algorithm of getting virtual database based on polynomial interpolation, while the pre-estimated result was disposed by particle filter. Experimental result shows that this method can generate a quick, simple fine-grained localization information database, and improve the positioning accuracy at the same time.
Go to article

Abstract

The paper deals with frequency estimation methods of sine-wave signals for a few signal cycles and consists of two parts. The first part contains a short overview where analytical error formulae for a signal distorted by noise and harmonics are presented. These formulae are compared with other accurate equations presented previously by the authors which are even more accurate below one cycle in the measurement window. The second part contains a comparison of eight estimation methods (ESPRIT, TLS, Prony LS, a newly developed IpDFT method and four other 3-point IpDFT methods) in respect of calculation time and accuracy for an ideal sine-wave signal, signal distorted by AWGN noise and a signal distorted by harmonics. The number of signal cycles is limited from 0.1 to 3 or 5. The results enable to select the most accurate/ fastest estimation method in various measurement conditions. Parametric methods are more accurate but also much slower than IpDFT methods (up to 3000 times for the number of samples equal to 5000). The presented method is more accurate than other IpDFT methods and much faster than parametric methods, which makes it possible to use it as an alternative, especially in real-time applications.
Go to article

Abstract

Sample-time errors can greatly degrade the dynamic range of a time-interleaved sampling system. In this paper, a novel correction technique employing a cubic spline interpolation is proposed for inter-channel sample-time error compensation. The cubic spline interpolation compensation filter is developed in the form of a finite-impulse response (FIR) filter structure. The correction method of the interpolation compensation filter coefficients is deduced. A 4GS/s two-channel, time-interleaved ADC prototype system has been implemented to evaluate the performance of the technique. The experimental results showed that the correction technique is effective to attenuate the spurious spurs and improve the dynamic performance of the system.
Go to article

This page uses 'cookies'. Learn more