Search results

Filters

  • Journals
  • Date

Search results

Number of results: 5
items per page: 25 50 75
Sort by:

Abstract

The goal of the proposed computational model was to evaluate the dynamical properties of air gauges in order to exploit them in such industrial applications as in-process control, form deviation measurement, dynamical measurement. The model is based on Reynolds equations complemented by the k-ε turbulence model. The boundary conditions were set in different areas (axis of the chamber, side surfaces, inlet pipeline and outlet cross-section) as Dirichlet's and Neumann's ones. The TDMA method was applied and the efficiency of the calculations was increased due to the "line-by-line" procedure. The proposed model proved to be accurate and useful for non-stationary two-dimensional flow through the air gauge measuring chamber.
Go to article

Abstract

In the article, the authors analyze and discuss several models used to the calculation of air gauge characteristics. The model based on the actual mass flow (which is smaller than the theoretical one) was proposed, too. Calculations have been performed with a dedicated software with the second critical parameters included. The air gauge static characteristics calculated with 6 different models were compared with the experimental data. It appeared that the second critical parameters model (SCP) provided the characteristics close to the experimental ones, with an error of ca. 3% within the air gauge measuring range.
Go to article

Abstract

Power systems that are highly loaded, especially by a stochastic supply of renewables and the presence of storages, require dynamic measurements for their optimal control. Phasor measurement units (PMUs) can be used to capture electrical parameters of a power system. Standards on the PMU dynamic performance have been modified to incorporate their new dynamic mode of operation. This paper examines the PMU dynamic performance and proposes essential algorithms for measurement accuracy verification. Measurements of dynamic input signals, which vary in amplitude or frequency, were taken during automated tests of two PMUs. The test results are presented and expounded with further recommendation for the performance requirements. This paper also presents and examines applied testing procedures with relevance to the specifications of the IEEE Standard for Synchrophasor C37.118.1™-2011 and its amendment C37.118.1a™-2014.
Go to article

Abstract

Power system state estimation is a process of real-time online modeling of an electric power system. The estimation is performed with the application of a static model of the system and current measurements of electrical quantities that are encumbered with an error. Usually, a model of the estimated system is also encumbered with an uncertainty, especially power line resistances that depend on the temperature of conductors. At present, a considerable development of technologies for dynamic power line rating can be observed. Typically, devices for dynamic line rating are installed directly on the conductors and measure basic electric parameters such as the current and voltage as well as non-electric ones as the surface temperature of conductors, their expansion, stress or the conductor sag angle relative to the plumb line. The objective of this paper is to present a method for power system state estimation that uses temperature measurements of overhead line conductors as supplementary measurements that enhance the model quality and thereby the estimation accuracy. Power system state estimation is presented together with a method of using the temperature measurements of power line conductors for updating the static power system model in the state estimation process. The results obtained with that method have been analyzed based on the estimation calculations performed for an example system - with and without taking into account the conductor temperature measurements. The final part of the article includes conclusions and suggestions for the further research.
Go to article

Abstract

The possibility of distinguishing and assessing the influences of defects in particular pump elements by registering vibration signals at characteristic points of the pump body would be a valuable way for obtaining diagnostic information. An effective tool facilitating this task could be a well designed and identified dynamic model of the pump. When applied for a specific type of the pump, such model could additionally help to improve its construction. This paper presents model of axial piston positive displacement pump worked out by the authors. After taking the simplifying assumptions and dividing the pump into three sets of elements, it was possible to build a discrete dynamic model with 13 degrees of freedom. According to the authors' intention, the developed dynamic model of the multi-piston pump should be used for damage simulation in its individual elements. By gradual change in values of selected construction parameters of the object (for example: stiffness coefficients, damping coefficients), it is possible to perform simulation of wear in the pump. Initial verification of performance of the created model was done to examine the effect of abrasive wear on the swash plate surface. The phase trajectory runs estimated at characteristics points of the pump body were used as a useful tool to determine wear of pump elements.
Go to article

This page uses 'cookies'. Learn more