A study was undertaken to investigate the effects of crumb rubber on the strength and mechanical behaviour of Rubberized cement soil (RCS). In the present investigation, 26 groups of soil samples were prepared at five different percentages of crumb rubber content, four different percentages of cement content and two different finenesses of crumb rubber particle. Compressive strength tests were carried out at the curing age of 7 days, 14 days, 28 days and 90 days. The test results indicated that the inclusion of crumb rubber within cement soil leads to a decrease in the compressive strength and stiffness and improves the cement soil’s brittle behaviour to a more ductile one. A reduction of up to 31% in the compressive strength happened in the 20% crumb content group. The compressive strength increases with the increase in the cement content. And the enlargement of cement content is more efficient at low cement content.
Light-weight Self-Compacting Concrete (LWSCC) might be the answer to the increasing construction requirements of slenderer and more heavily reinforced structural elements. However there are limited studies to prove its ability in real construction projects. In conjunction with the traditional methods, artificial intelligent based modeling methods have been applied to simulate the non-linear and complex behavior of concrete in the recent years. Twenty one laboratory experimental investigations on the mechanical properties of LWSCC; published in recent 12 years have been analyzed in this study. The collected information is used to investigate the relationship between compressive strength, elasticity modulus and splitting tensile strength in LWSCC. Analytically proposed model in ANFIS is verified by multi factor linear regression analysis. Comparing the estimated results, ANFIS analysis gives more compatible results and is preferred to estimate the properties of LWSCC.
The paper presents results of compressive strength investigations of EN AC-44200 based aluminum alloy composite materials reinforced with aluminum oxide particles at ambient and at temperatures of 100, 200 and 250C. They were manufactured by squeeze casting of the porous preforms made of α-Al2O3 particles with liquid aluminum alloy EN AC-44200. The composite materials were reinforced with preforms characterized by the porosities of 90, 80, 70 and 60 vol. %, thus the alumina content in the composite materials was 10, 20, 30 and 40 vol.%. The results of the compressive strength of manufactured materials were presented and basing on the microscopic observations the effect of the volume content of strengthening alumina particles on the cracking mechanisms during compression at indicated temperatures were shown and discussed. The highest compressive strength of 470 MPa at ambient temperature showed composite materials strengthened with 40 vol.% of α-Al2O3 particles.
Plastic obtained from the discarded computers, televisions, refrigerators, and other electronic devices is termed as e-plastic waste. E-plastic waste is non-biodegradable waste. This paper focuses to investigate the replacement of fine aggregate with plastic aggregate obtained from e-plastic. The paper presents a detailed comparison of concrete properties (i.e.: compressive strength, tensile strength, flexural strength, density and workability) for normal concrete and concrete containing e-plastic fine aggregates. The testing was conducted according to the ASTM standards. 28-day Compressive, Flexural and Split tensile strengths were determined. In addition to the effect of e-plastic fine aggregate, silica fume is added as an admixture to find the effect on strengths. Authors have performed a compressive, flexural and tensile test of concrete mix with various percentages of e-plastic aggregates (i.e., 0, 5, 10, 15 and 20%) and silica fume (i.e.: 0, 5 and 10%) and concrete densities are also considered. It has been concluded that an increase in the e-plastic fine aggregate results in reduction in densities, compressive, flexural and tensile strength values. However, when we add silica fume to the concrete mixture it leads to strength values similar to the control mixture. The optimum obtained concrete blend contained 5% e-plastic fine aggregates and 10% silica fume. The addition of silica fume in concrete mixtures increases the 28-day compressive, flexural and tensile strengths. Moreover, the density of concrete decreases with the increase in the e-plastic aggregates.
An uniaxial compression mechanical model for the roof rock-coal (RRC) composite sample was established in order to study the effects of height ratio of roof rock to coal on the structural strength of composite sample. The composite sample strengths under different height ratios were established through stress and strain analysis of the sample extracted from the interface. The coal strength near the interface is enhanced and rock strength near the interface weakened. The structural strength of composite sample is synthetically determined by the strengths of rock and coal near and far away from the interface. The area with a low strength in composite sample is destroyed firstly. An analytical model was proposed and discussed by conducting uniaxial compression tests for sandstone-coal composite samples with different height ratios, and it was found that the structural strength and elastic modulus decrease with a decrease in height ratio. The coal strengths far away from the interface determine the structural strengths of composite sample under different height ratios, which are the main control factor for the structural strength in this test. Due to its lowest strength, the rock near the interface first experienced a tensile spalling failure at the height ratio of 9:1, without causing the structural failure of composite sample. The coal failure induces the final failure of composite sample.
This paper presents the details of optimized mix design for normal strength and high performance concrete using particle packing method. A critical review of mix design methods have been carried out for normal strength concrete using American Concrete Institute (ACI) and Bureau of Indian Standards (BIS) methods highlighting the similarities and differences towards attaining a particular design compressive strength. Mix design for M30 and M40 grades of concrete have been carried out using ACI, BIS and particle packing methods. Optimization of concrete mix has been carried out by means of particle packing method using EMMA software, which employs modified Anderson curve to adjust the main proportions. Compressive strength is evaluated for the adjusted proportions and it is observed that the mixes designed by particle packing method estimates compressive strength closer to design compressive strength. Further, particle packing method has been employed to optimize the ingredients of high performance concrete and experiments have been carried out to check the design adequacy of the desired concrete compressive strength.
Nano technology is an emerging field of interest for civil engineering application. Among the nano materials presently used in concrete, nano-silica possess more pozzolanic nature. It has the capability to react with the free lime during the cement hydration and forms additional C-S-H gel giving strength, impermeability and durability to concrete. Present paper investigates the effects of addition of nano silica in normal strength concrete. Three types of nano-silica in the form of nano suspension having different amount of silica content have been investigated. Mix design has been carried out by using particle packing method. X-Ray diffraction (XRD) analysis has been carried out to find the chemical composition of control concrete and nano modified concrete. Further, experimental investigations have been carried out to characterize the mechanical behaviour in compression, tension and flexure. It has been observed that the addition of nano-silica in normal strength concrete increased the compressive strength and decreased the spilt tensile strength and flexural strength. Also, Rapid chloride permeability test (RCPT) has been conducted to know the chloride permeability of control concrete, nano modified concrete, and nano coated concrete. It has been observed that the chloride permeability is less for nano coated concrete.
The subject of the research was the Middle Miocene red algal limestone from the Włochy deposit, which is currently the only place of exploitation of the Pińczów Limestone representing a local type of the Leitha Limestone. The collected samples of this rock belong to the organodetric facies of diverse grain size and sorting of clastic material. Considering the proportions of characteristic skeleton remains, the composition of the coarse-grained organodetric facies is red algal-foraminiferalbryozoic, while of the fine-grained facies is foraminiferal-red algal. The cement of these rocks is predominantly sparite compared to micrite-clay matrix. A complement to petrographic studies was the chemical analysis and identification of mineral phases with X-ray diffraction. Moreover, physical and mechanical properties of samples were analyzed. Porosity of the rock was assessed in the polarizing and scanning microscope (SEM-EDS) observations, as well as with a porosimetric tests. The coarse-detrital limestone with a dominant binder in the form of intergranular cement is characterized by the apparent density sometimes exceeded 1.90 Mg/m3, while fine-grained limestone has the highest water absorbability (above 20%) and total porosity (about 40%). The above properties influenced high water absorption by capillarity, limiting the possibility of using limestone in places exposed to moisture. The observed relationship between the ultrasonic waves velocity and the uniaxial compressive strength gives the possibility of predicting the value of the latter parameter in the future. The limestones from Włochy deposit do not differ in quality from the previously used Pińczów Limestones, and their technical parameters predestine them for use as cladding material with insulating properties.
Casting is the most widely used manufacturing technique. Furan No-bake mould system is very widely accepted in competitive foundry industries due to its excellent characteristics of producing heavy and extremely difficult castings. These castings have excellent surface finish and high dimensional stability. Self setting and high dimensional stability are the key characteristics of FNB mould system which leads to reduce production cycle time for foundry industries which will ultimately save machining cost, labour cost and energy. Compressive strength is the main aspect of furan no bake mould, which can be improved by analyzing the effect of various parameters on it. ANN is a useful technique for determining the relation of various parameters like Grain Fineness Number, Loss on Ignition, pH, % resin and temperature of sand with compressive strength of the FNB mould. Matlab version: R2015a version 8.3 software with ANN tool box can be used to gain output of relation. This paper deals with the representation of relationship of various parameters affecting on the compressive strength of FNB mould
Synthetic polymer latexes, such as styrene–butadiene rubber (SBR) latex addition in Portland cement has gained wider acceptance in many applications in the construction industry. Polymer-modified cementitious systems seals the pores and micro cracks developed during hardening of the cement matrix, by dispersing a film of polymer phase throughout the concrete. A comprehensive set of experimental test were conducted for studying the compressive properties of SBR latex polymer with crimped polypropylene fibres at relative volume fractions of 0.1 and 0.3%. The results indicated that the addition of polypropylene fibre has little effect on the reduction in the workability of concrete composite containing fly ash and SBR Latex. Increase in polypropylene fibres upto 0.3% Vf showed increase in compressive strength upto 57.5 MPa. The SBR concrete without fibre showed an increase in strength upto 20% compared to plain concrete. Test results also indicated that the compressive strength was increased in SBR fibre concrete by means of an ordinary dry curing process than wet curing because of their excellent water retention due to polymer film formation around the cement grains. On the contrary the compressive strength reduces for SBR fibre concretes under wet curing compared to dry curing.