The preliminary stage of asphalt mixture production involves the drying and dedusting of coarse aggregates. The most common types of coarse aggregates used are limestone and basalt. In the process of drying and dedusting the dryer filter accumulates large quantities of waste in the form of mineral powder. This paper introduces an investigation into limestone powder waste as a potential microfiller of polymer composites. Physical characteristics such as the granulation the of powder collected from the filter - in terms of the season of its collection and the type of input materials used - were analysed. A scanning electron microscope (SEM) was used for the investigation described within this paper. The obtained results were compared against those of other materials which can be used as polymer composites microfillers.
During austral summer phytoplankton is the main component of food of E. superba postlarval stages. Diatomeae: Thalassiosira spp., Nitzschia spp. and tiny Pennatae constitue 98% of all consumed food particles. 91% of algae consumed were of 8—40 μm, and their mean size is 21.4 μm. The mean amount of algae found in of Euphausia superba was about 1700 per individual. The differences in species composition and the size of algae eaten by juvenes, preadult and adult individuals decrease the food competition between particular age groups of E. superba.
The use of biomass in the energy industry is the consequence of ongoing efforts to replace Energy from fossil fuels with energy from renewable sources. However, due to the diversity of the biomass, its use as a solid fuel generates waste with diverse and unstable chemical composition. Waste from biomass combustion is a raw material with a very diverse composition, even in the case of using only one type of biomass. The content of individual elements in fly ash from the combustion of biomass ranges from zero to tens of percent. This makes it difficult to determine the optimal recovery methods. The ashes from the combustion of biomass are most commonly used in the production of building materials and agriculture. This article presents the elemental composition of the most commonly used biomass fuels. The results of the analysis of elemental composition of fly ashes from the combustion of forest and agricultural biomass in fluidized bed boilers used in the commercial power industry were presented. These ashes are characterized by a high content of calcium (12.3–19.4%), silicon (1.2–8.3%), potassium (0.05–1.46%), chlorine (1.1–6.1%), and iron (0.8–6.5%). The discussed ashes contained no sodium. Aluminum was found only in one of the five ashes. Manganese, chromium, copper, nickel, lead, zinc, sulfur, bismuth, titanium and zirconium were found in all of the examined ashes. The analysis of elemental composition may allow for a preliminary assessment of the recovery potential of a given ash.
Changes in the amount of basic nitrogen fractions (total, protein and non-protein nitrogen) were studied in an annual cycle. Significant seasonal changes were noted, minima occurring in Antarctic winter and maxima during spring-summer season. These changes are due mainly to high fluctuations of water content in krill in the annual cycle.
The paper is concerned with the most fundamental compositional divide to be found in lyrical discourse, consisting in that the latter one is normally split into an empirical part, presenting the author’s concrete experience, and a focal part, where the author discovers some signifi cant truth or/and changes her attitude towards the world. It is claimed in the paper that, more generally, one of the specifi c linguistic properties of focal fragments is their higher and/or specially underscored informativity, and, in particular, one of the means recruited to emphasize it is inverted word order.
Fabrication and microstructure of the AlSi11 matrix composite containing 10 % volume fraction of CrFe30C8 particles were presented in this paper. Composite suspension was manufactured by using mechanical stirring. During stirring process the temperature of liquid metal, time of mixing and rotational speed of mixer were fixed. After stirring process composite suspension was gravity cast into shell mould. The composites were cast, applying simultaneously an electromagnetic field. The aim of the present study was to determine the effect of changes in the frequency of the current power inductor on the morphology of the reinforcing phase in the aluminum matrix. The concept is based on the assumption that a chromium-iron matrix of CrFe30C8 particles dissolves and residual carbide phases will substantially strengthen the composite. The microstructure and interface structure of the AlSi11/CrFe30C8 composite has been studied by optical microscopy, scanning microscopy and X-ray diffraction.
Applying the commonly accepted definitions of identity to landscape as our field of research, in particular landscape in protected areas, we assume that identity is the deepest relationship with the landscape (surroundings) perceived by man, with its historical layers of content (the culture and tradition of a place) and form (the canon of a place). An evaluation of change in time should be the keynote of deliberations on place identity. Basing on the current status of research, a review of specialist literature and the author’s experience to date, the above definitions and terms may be referenced to talk about “former” and “new” place identity, especially if we acquiesce to what is termed “the culture of a place” that originates in love for it and willingness to participate in the act of creation that has been launched upon the site. Author tries to explain this fenomenom on example of revitalization, on scale of conntry or even the Europe – the cultural – strategic landscape od Zamość Fortress.
Nematoda, Tardigrada, Rotifera and Crustacea composition in different freshwater habitats on Spitsbergen (Arctic) and King George Island (Antarctic) was presented. In all surveyed groups more genera and species were recorded from Spitsbergen than from King George Island. Habitats richest in taxa were moss banks and thaw ponds, whereas streams were poorest in species. In all groups in both regions cosmopolitan species dominated, but higher number of endemic species was recorded on King George Island. Regarding species composition in surveyed groups it can be suggested that freshwater habitats on Spitsbergen are more similar to each other than those on King George Island.
Changes in body mass and body reserves of Little Auks (Alle alle) were studied throughout the breeding season. Body mass loss after chick hatching was analyzed with respect to two hypotheses: (1) mass loss reflects the stress of reproduction, (2) mass loss is adaptive by reducing power consumption during flight. Body mass of both males and females increased during incubation, dropped abruptly after hatching, and remained stable until the end of the chick-rearing period. These changes were largely due to change in mass of fat reserves. Body mass, fat, and protein reserves, when corrected for body size, did not differ between sexes at the end of incubation. Female size-corrected body mass at that time was correlated with peak body mass of chicks. The estimated energy savings for flight due to the decline in adult body mass after chick hatching were small compared with the total energy expenditure of adults feedings chicks, which did not support hypothesis (2). The contribution to chick feeding was not equal; the ratio of females to males caught with food for chicks was 1.8. Size-corrected body mass during chick-rearing was lower in females, proportional to their higher chick feeding effort compared with males. Females, in contrast to males, lost protein reserves during chick-rearing. Digestive tract mass of adults increased by half throughout the breeding period. These findings supported elements of hypothesis (1). Despite high energy expenditure rates, both sexes had about 10 g of fat reserves at the end of chick feeding. Body mass of both sexes was constant during the greater part of the chick-feeding period. It was suggested therefore that mass loss is regulated with respect to lower fat reserves required during chick-rearing.
The aim of research was the elaboration of the synthesis of new organic monomer applicable in gelcasting. The substance named 3,4-di-acryloyl-D-mannitol which contains two acryloyl groups and four hydroxyl groups in its molecule has been synthesized. The monomer has been then applied in the preparation of Al2O3-ZrO2 composites by gelcasting and subsequent sintering. Rheological properties of ceramic suspensions have been examined, as well as the properties of green and sintered bodies. SEM observations allowed to determine the distribution of zirconia grains in alumina matrix. Density, Vickers hardness and fracture toughness of ZTA composites have been measured. The new monomer, that is diacryloyl derivative of mannitol, is less sensitive to the oxygen inhibition than commonly used in gelcasting and commercially available 2-hydroxyethyl acrylate.
The paper presents the method of preparing a composite slurry composed of AlSi11 alloy matrix and 10 vol.% of SiC particles, as well as the method of its high-pressure die casting and the measurement results concerning the castability of the obtained composite. Composite castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. There were found the regression equations describing the change of castability of the examined composite as a function of pressure die casting process parameters. The conclusion gives the analysis and the interpretation of the obtained results.
Oxide fiber-reinforced Ni-base composites have long been considered as attractive heat-resistant materials. After several decades of active research, however, interest in these materials began to decline around mid-1990’s due chiefly to 1) a lack of manufacturing technology to grow inexpensive single-crystal oxide fibers to be used in structural composites, and 2) fiber strength loss during processing due to chemical interactions with reactive solutes in the matrix. The cost disadvantage has been mitigated to a large extent by the development of innovative fiber fabrication processes such as the Internal Crystallization Method (ICM) that produces monocrystalline oxide fibers in a cost-effective manner. Fiber strength loss has been an equally restrictive issue but recent work has shown that it may be possible to design creep-resistant composites even when fiber surface reconstruction from chemical interactions has degraded the strength of extracted fibers tested outside the matrix. The key issue is the optimization of the composite- and interface structure. Reaction-formed defects may be healed by the matrix (or a suitable coating material) so that the fiber residing in the matrix may exhibit diminished sensitivity to flaws as compared to fibers extracted from the matrix and tested in isolation of the matrix. Generally, the Ni-base/Al2O3 composites exhibit acceptable levels of wettability and interface strength (further improved with the aid of reactive solutes), which are required for elevated-temperature creep-resistance. In order to harness the full potential of these composites, the quality of the interface as manifested in the fiber/matrix wettability, interface composition, interphase morphology, and interface strength must be designed. We identify key issues related to the measurement of contact angle, interface strength, and chemical and structural properties at the fiber/matrix interface in the Ni/alumina composites, and present the current state-ofthe-art in understanding and designing the Ni/alumina interface. There should be no doubt that optimization of the interface- and composite microstructure through judicious control of the fabrication process and surface modification shall yield technologically promising Ni-base/oxide fiber composites.
Multiferroic composites are very promising materials because of their applicability because the magnetoelectric effect occurs in them. The subject of the study were two multiferroic ceramic composites: leaded obtained from powder of the composition PbFe0.5Nb0.5O3 and ferrite powder of the composition Ni0.64Zn0.36Fe2O4 and unleaded which was obtained from the powder of the composition BaFe0.5Nb0.5O3 and the same ferrite powder Ni0.64Zn0.36Fe2O4. For the both multiferroic materials the following studies were conducted: SEM, BSE, EDS, XRD and the temperature dependence of dielectric constant ε(T). Using the previously developed method of calculating the magnetoelectric coupling factor (g), based on dielectric measurements, the magnitude of the magnetoelectric effect in the multiferroic composites was determined.
The method of pressure die casting of composites with AlSi11 alloy matrix reinforced with 10 vol. % of SiC particles and the analysis of the distribution of particles within the matrix is presented. The composite castings were produced at various values of the piston velocity in the second stage of injection, at diverse intensification pressure values, and various injection gate width values. The distribution of particles over the entire cross-section of the tensile specimen is shown. The index of distribution was determined on the basis of particle count in elementary measuring fields. The regression equation describing the change of the considered index was found as a function of the pressure die casting parameters. The conclusion presents an analysis of the obtained results and their interpretation.
This paper deals with computer modelling of the retention of a synthetic diamond particle in a metallic matrix produced by powder metallurgy. The analyzed sintered powders can be used as matrices for diamond impregnated tools. First, the behaviour of sintered cobalt powder was analyzed. The model of a diamond particle embedded in a metallic matrix was created using Abaqus software. The preliminary analysis was performed to determine the mechanical parameters that are independent of the shape of the crystal. The calculation results were compared with the experimental data. Next, sintered specimens obtained from two commercially available powder mixtures were studied. The aim of the investigations was to determine the influence of the mechanical and thermal parameters of the matrix materials on their retentive properties. The analysis indicated the mechanical parameters that are responsible for the retention of diamond particles in a matrix. These mechanical variables have been: the elastic energy of particle, the elastic energy of matrix and the radius of plastic zone around particle.
This paper discusses the mechanical properties of a material fabricated from commercially available metal powder mixtures designed for use as a metal matrix of diamond impregnated composites. The mixtures with the catalogue numbers CSA and CSA800 provided by a Chinese producer are suitable for experimental laboratory testing. The specimens were fabricated in a graphite mould using hot pressing. The material was tested for density, porosity, hardness, and tensile strength under static loading. A scanning electron microscope (SEM) was used to analyze the microstructure and cleavage fracture of broken specimens. It was essential to determine how the chemical composition and the fabrication process affected the microstructure and properties of the material. The properties of the sinters were compared with those of hot pressed specimens fabricated from sub-micron size cobalt powder (Cobalt SMS). Although the as-consolidated material is inferior to cobalt, it displays a favourable combination of hardness, yield strength and ductility, and seems to have a great potential for moderate and general purpose applications.
The measurement results concerning the abrasive wear of AlSi11-SiC particles composites are presented in paper. The method of preparing a composite slurry composed of AlSi11 alloy matrix and 10, 20% vol.% of SiC particles, as well as the method of its highpressure die casting was described. Composite slurry was injected into metal mould of cold chamber pressure die cast machine and castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. Very good uniform arrangement of SiC particles in volume composite matrix was observed and these results were publicated early in this journal. The kinetics of abrasive wear and correlation with SiC particles arrangement in composite matrix were presented. Better wear resistance of composite was observed in comparison with aluminium alloy. Very strong linear correlation between abrasive wear and particle arrangement was observed. The conclusion gives the analysis and the interpretation of the obtained results.
The paper presents the method of preparing a composite slurry composed of AlSi11 alloy matrix and 10 vol.% of SiC particles, as well as the method of its high-pressure die casting and the measurement results concerning the tensile strength, the yield point, the elongation and hardness of the obtained composite. Composite castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. There were found the regression equations describing the change of mechanical properties of the examined composite as a function of pressure die casting process parameters. The conclusion gives the analysis and the interpretation of the obtained results.
Transverse effective thermal conductivity of the random unidirectional fibre-reinforced composite was studied. The geometry was circular with random patterns formed using random sequential addition method. Composite geometries for different volume fraction and fibre radii were generated and their effective thermal conductivities (ETC) were calculated. Influence of fibre-matrix conductivity ratio on composite ETC was investigated for high and low values. Patterns were described by a set of coordination numbers (CN) and correlations between ETC and CN were constructed. The correlations were compared with available formulae presented in literature. Additionally, symmetry of the conductivity tensor for the studied geometries of fibres was analysed.
Carotenoids in six species of the lichens from Antarctica (Xanthoria eleguns, Caloplaca regalis, Usnea antarctica, U. fasciata, Himantormia lugubris and Ramalina terebrata) have been investigated by means of column and thin — layer chromatography. The following carotenoids were found: β-carotene, α- and β-cryptoxanthin, canthaxanthin. lycophyll, lycoxanthin, lutein, lutein epoxide, zeaxanthin, antheroxanthin, adonixanthin, diatoxanthin, rhodoxanthin, rhodoxanthm derivative, α-doradexanthin, astaxanthin, astaxanthin ester, mutatochrome, mutatoxanthin and cryptoflavin. Most frequently occurred β-carotene, β-cryptoxanthin, lutein epoxide, zeaxanthin and mutatoxanthin. The total carotenoid content ranged from 10.242 (Ramalina terebrata) to 18.700 mg/g dry weight (Himantormia lugubris) in October and from 4.765 (Ramalina terebrata) to 12.462 mg/g dry weight (Caloplaca regalis) in February.
In this study, free and forced vibration responses of carbon nanotube reinforced uniform and tapered composite beams are investigated. The governing differential equations of motion of a carbon nanotube (CNT) reinforced uniform and tapered composite beams are presented in finite element formulation. The validity of the developed formulation is demonstrated by comparing the natural frequencies evaluated using present FEM with those of available in literature. Various parametric studies are also performed to investigate the effect of aspect ratio, percentage of CNT content, ply orientation, and boundary conditions on natural frequencies and mode shapes of a CNT reinforced composite beam. It was observed that the addition of carbon nanotube in fiber reinforced polymer composite (FRP) beam enhances the stiffness of the structure which consequently increases the natural frequencies and alters the mode shapes.
Humic acids, isolated from selected soils of Grønfjorden area (Spitsbergen) were investigated in terms of molecular composition and resistance of decomposition. The degree of soils organic matter stabilization has been assessed with the use of modern instrumental methods (nuclear magnetic resonance spectroscopy (CP/MAS 13C-NMR). Analysis of the humic acids showed that aromatic compounds prevail in the organic matter formed in cryoconites, located on the glaciers surfaces. The predominance of aliphatic fragments is revealed in the soils in tidal zone that form on the coastal terrace. This could be caused by sedimentation of fresh organic matter exhibiting low decomposition stage due to the harsh climate and processes of hydrogenation in the humic acids, destruction of the C-C bonds and formation of chains with a high hydrogen content. These processes result in formation of aliphatic fragments in the humic acids. In general, soils of the studied region characterizes by low stabilized soil organic matter which is indicated by low aromaticity of the HAs.
The study aimed to apply the protection from damage to engineering facilities located near a planned underwater aggregate extraction. The analysis was conducted in compliance with mining regulations and expert opinions. The study also aimed to assess the precision and correctness of the extraction, due to economic aspects. To reach the goals, in-situ research of the mining area was conducted, with the help of an advanced bathymetric device, based on the USV methodology. The instrument – named by the author as Smart-Sonar-Boat – was especially designed for underwater surveys in open-pit aggregate mines. The study analyzed the “Dwory” open-pit mine, located in southern Poland in the city of Oświęcim. The bathymetric results obtained contributed to improving the observation of changes in the bottom during the extraction. The applied USV method allowed for conducting the reliable evaluation of the mining work.
Switched reluctance motors (SRMs) are still under development to maximise their already proven usefulness.Amagnetic circuit of theSRMcan be made of soft magnetic composites (SMCs). The SMCs are composed of iron powder with dielectric and have a lot of advantages in comparison to commonly used electrical steel. The paper deals with the modelling and analysis of theSRMproduced by Emerson Electric Co. forwashing machines. Numerical calculations and modelling were done using the FEMM 4.2 program. Magnetic flux densities and magnetic flux lines were calculated, as well as electromagnetic torque and inductance for changing the position of a stator to a rotor. The obtained results were compared with other measurement results and are quite similar. The developed numerical model will be used for the project of a motor with an SMC magnetic circuit.
Dynamic Mine disasters can be induced by the instability and failure of a composite structure of rock and coal layers during coal mining. Coal seam contains many native defects, severely affecting the instability and failure of the compound structure. In this study, the effects of coal persistent joint on the strength and failure characteristics of coal-rock composite samples were evaluated using PFC2D software. The results show that with the increase of included angle α between the loading direction and joint plane direction, the uniaxial compressive stress (UCS) and peak strain of composite samples first decrease and then gradually increase. The elastic moduli of composite samples do not change obviously with α. The peak strain at α of 45° is the lowest, and the UCS at α of 30° is the smallest. This is inconsistent with theoretical analysis of lowest UCS at α of 45°. This is because that the local stress concentration caused by the motion inconformity of composite samples may increase the average axial stress of upper wall in PFC2D software. Moreover, the coal persistent joint promotes the transformation from the unstable crack expansion to the macro-instability of composite samples, especially at α of 30° and 45°. The majority of failures for composite samples occur within the coal, and no obvious damage is observed in rock. Their failure modes are shear failure crossing or along the coal persistent joint. The failure of composite sample at α of 30° is a mixed failure, including the shear failure along the persistent joint in coal and tensile failure of rock induced by the propagation of coal persistent joint.