“Soon we will be able to fit the contents of the Encyclopedia Britannica on a head of a pin,” the famous physicist Richard Feynman argued back in the 1960s. Perhaps even he would be amazed at the possibilities now offered by carbon nanotubes, several hundred thousand times tinier than a pin. Their amazing properties have been exploited in an integrated circuit developed at the Karlsruhe Institut für Technologie.
Operational Transresistance Amplifier (OTRA) has been a topic of great interest recently. OTRA has proved itself to be an appropriate device for the analog applications. As MOS scaling suffers from various problems, carbon nanotube field effect transistor (CNTFET) has came into light as one of the brightest alternative for FET (Field Effect Transistors) based devices. This work has introduced a new CNTFET based OTRA which is capable of realising inverse low pass filter using two OTRAs and few passive elements. CNTFET based OTRA has been designed and simulated at 10nm technology node. The working ability of the designed model has been conformed using HSPICE simulation. It is compared with conventional CMOS based OTRA. The comparative analysis has revealed improvement in various performance parameters. The paper also presents how change in number of carbon nanotube in CNTFETs in OTRA circuit affects the transresistance gain and input impedance. The optimized results are also discussed to improve transresistance gain and input impedance. The paper also dealt with the realisation of inverse low pass filter using proposed CNTFET based OTRA.
The removal of benzene (B) and toluene (T) from aqueous solution by multi walled, single walled, and hybrid carbon nanotubes (MWCNTs, SWCNTs, and HCNTs) was evaluated for a nanomaterial dose of 1 g/l, concentration of 10-100 mg/l, and pH 7. The equilibrium amount removed by SWCNTs (B: 9.98 mg/g and T: 9.96 mg/g) was higher than for MWCNTs and HCNTs. Toluene has a higher adsorption tendency on CNTs than benzene, which is related to the increasing water solubility and the decreasing molecular weight of the compounds. The SWCNTs performed better for B and T sorption than the MWCNTs and HCNTs. Isotherms study based on isofit program indicate that the Generalized Langmuir-Freundlich (GLF) isotherm expression provides the best fit for benzene sorption, and that Brunauer-Emmett-Teller (BET) isotherm is the best fit for toluene adsorption by SWCNT. SWCNTs are efficient B and T adsorbents and possess good potential applications to water and wastewater treatment and maintain water of high quality that could be used for cleaning up environmental pollution.
A number of micromechanical investigations have been performed to predict behaviour of composite interfaces, showing that the detailed behaviour of the material at these interfaces frequently dominates the behaviour of the composite as a whole. The interfacial interaction is an extremely complex process due to continuous evolution of interfacial zones during deformation and this is particularly true for carbon nanotubes since the interfacial interaction is confined to the discrete molecular level. The atomic strain concept based upon Voronoi tessellation allows analyzing the molecular structure atom by atom, which may give a unique insight into deformation phenomena operative at molecular level such as interface behaviour in nanocomposites.
In this paper, the authors investigate a cylindrical shell reinforced by carbon nanotubes. The critical buckling load is calculated using analytical method when it is subjected to compressive axial load. The Mori-Tanaka method is firstly utilized to estimate the effective elastic modulus of composites having aligned oriented straight CNTs. The eigenvalues of the problem are obtained by means of an analytical approach based on the optimized Rayleigh-Ritz method. There is presented a study on the effects of CNTs volume fraction, thickness and aspect ratio of the shell, CNTs orientation angle, and the type of supports on the buckling load of cylindrical shells. Furthermore the effect of CNTs agglomeration is investigated when CNTs are dispersed none uniformly in the polymer matrix. It is shown that when the CNTs are arranged in 90 degrees direction, the highest critical buckling load appears. Also, the results are plotted for different longitudinal and circumferential mode numbers. There is a specific value for aspect ratio of the cylinder that minimizes the buckling load. The results reveal that for very low CNTs volume fractions, the volume fraction of inclusions has no important effect on the critical buckling load.
A ceria loaded carbon nanotubes (CeO2/CNTs) nanocomposites photocatalyst was prepared by chemical precipitation, and the preparation conditions were optimized using an orthogonal experiment method. HR-TEM, XRD, UV-Vis/DRS, TGA and XPS were used to characterize the photocatalyst. Nitrogen adsorption-desorption was employed to determine the BET specific surface area. The results indicated that the photocatalyst has no obvious impurities. CeO2 was dispersed on the carbon nanotubes with a good loading effect and high loading efficiency without agglomeration. The catalyst exhibits a strong ability to absorb light in the ultraviolet region and some ability to absorb light in the visible light region. The CeO2/CNTs nanocomposites photocatalyst was used to degrade azo dye Acid Orange 7 (40 mg/L). The optical decolorization rate was 66.58% after xenon lamp irradiation for 4 h, which is better than that of commercial CeO2 (43.13%). The results suggested that CeO2 loading on CNTs not only enhanced the optical decolorization rate but also accelerated the separation of CeO2/CNTs and water.
In this study, free and forced vibration responses of carbon nanotube reinforced uniform and tapered composite beams are investigated. The governing differential equations of motion of a carbon nanotube (CNT) reinforced uniform and tapered composite beams are presented in finite element formulation. The validity of the developed formulation is demonstrated by comparing the natural frequencies evaluated using present FEM with those of available in literature. Various parametric studies are also performed to investigate the effect of aspect ratio, percentage of CNT content, ply orientation, and boundary conditions on natural frequencies and mode shapes of a CNT reinforced composite beam. It was observed that the addition of carbon nanotube in fiber reinforced polymer composite (FRP) beam enhances the stiffness of the structure which consequently increases the natural frequencies and alters the mode shapes.