Early recognition of altered lactate levels is considered a useful prognostic indicator in dis- ease detection for both human beings and animals. It is reasonable therefore to hypothesize that a portable, point of care (POC) spectrophotometric device for analysis of lactate levels, may have an application for field veterinarians across a range of conditions and diagnostic procedures. In this study, a total of 72 cattle in the transition period underwent POC spectrophotometric lactate measurement with a portable device (The Vet Photometer) in the field, with a small portion of blood used for comparative ELISA evaluation. Lactate measurements were compared using a of Passing-Bablok regression analysis and Bland-Altman plots. The Vet Photometer lactate mea- surement results were in agreement with those generated by the ELISA method. Values for the agreement were derived, in a 95% CI between -1.3 and 0.99, and a positive correlation (r=0.71) between the two measurements. The equation y= 0.68x + 0.60 was achieved using a Pass- ing-Bablok regression analysis. There were no statistical differences in mean values between the measurement methods. In conclusion, a novel veterinary POC spectrophotometric device “Vet Photometer” is an accurate device for evaluation of lactate levels in healthy transition cows.
The aim of the research was to analyze the possibility of using mobile laser scanning systems to acquire information for production and/or updating of a basic map and to propose a no-reference index of this accuracy assessment. Point clouds have been analyzed in terms of content of interpretation and geometric potential. For this purpose, the accuracy of point clouds with a georeference assigned to the base map objects was examined. In order to conduct reference measurements, a geodetic network was designed and also additional static laser scanning data has been used. The analysis of mobile laser scanning (MLS) data accuracy was conducted with the use of 395 check points. In the paper, application of the total Error of Position of the base-map Objects acquired with the use of MLS was proposed. Research results were related to reference total station measurements. The resulting error values indicate the possibility to use an MLS point cloud in order to accurately determine coordinates for individual objects for the purposes of standard surveying studies, e.g. for updating some elements of the base map content. Nevertheless, acquiring MLS point clouds with satisfying accuracy not always is possible, unless specific resolution condition is fulfilled. The paper presents results of accuracy evaluation in different classes of base-map elements and objects.
A checkweigher is an automatic machine to measure the weight of in-motion products. It is usually located around the end of the production process and ensures the weight of a product within specified limits. Any products are taken out of line if their weights are out of the specified limits. It is usually equipped with an optical device. It is used to make a trigger to set the time duration to allow a product to move completely on the weigh belt for sampling the weight. In this paper, a new method of mass measurement for checkweighers is proposed which uses just signal processing without the optical device. The effectiveness of the method is shown through experiments. Also a possibility of faster estimation of weight is shown.
The tendencies of modern industry are to increase the quality of manufactured products, simultaneously decreasing production time and cost. The hybrid system combines advantages of the high accuracy of contact CMM and the high measurement speed of non-contact structured light optical techniques. The article describes elements of a developed system together with the steps of the measurement process of the hybrid system, with emphasis on segmentation algorithms. Additionally, accuracy determination of such a system realized with the help of a specially designed ball-plate measurement standard is presented.
The interesting properties of a class of expanding systems are discussed. The operation of the considered systems can be described as follows: the input signal is processed by a linear dynamic converter in subsequent time intervals, each of them is equal to Ti. Processing starts at the moments n · Ti, always after zeroing of converter initial conditions. For smooth input signals and a given transfer function of the converter one can suitably choose Ti and the gain coefficient in order to realize the postulated linear operations on input signals, which is quite different comparing it to the operation realized by the converter. The errors of postulated operations are mainly caused by non-smooth components of the input signal. The principles for choice of system parameters and rules for system optimization are presented in the paper. The referring examples are attached too.
The TerraSAR-X add-on for Digital Elevation Measurement ( TanDEM-X) mission launched in 2010 is another programme – after the Shuttle Radar Topography Mission (SRTM) in 2000 – that uses space-borne radar interferometry to build a global digital surface model. This article presents the accuracy assessment of the TanDEM-X intermediate Digital Elevation Model (IDEM) provided by the German Aerospace Center (DLR) under the project “Accuracy assessment of a Digital Elevation Model based on TanDEM-X data” for the southwestern territory of Poland. The study area included: open terrain, urban terrain and forested terrain. Based on a set of 17,498 reference points acquired by airborne laser scanning, the mean errors of average heights and standard deviations were calculated for areas with a terrain slope below 2 degrees, between 2 and 6 degrees and above 6 degrees. The absolute accuracy of the IDEM data for the analysed area, expressed as a root mean square error (Total RMSE), was 0.77 m.
This research presents comprehensive assessment of the precision castings quality made in the Replicast CS process. The evaluation was made based on quality of the surface layer, shape errors and the accuracy of the linear dimensions. Studies were carried out on the modern equipment, among other things a Zeiss Calypso measuring machine and profilometer were used. Obtained results allowed comparing lost wax process models and Replicast CS process.
The objective of research concerned verifying the accuracy of the location and shape of selected lakes presented on topographical maps from various periods, drawn up on different scales. The area of research covered lakes situated in North- Western Poland on the Międzychód-Sieraków Lakeland . An analysis was performed of vector maps available in both analogue and digital format. The scales of these studies range from 1:50 000 to 1:10 000. The source materials were current for the years 1907 through 2013. The shape and location of lakes have been verified directly by means of field measurements performed using the GPS technology with an accuracy class of RTK. An analysis was performed of the location and shape of five lakes. The analysed water regions were vectorised, and their vector images were used to determine quantitative features: the area and length of the shoreline. Information concerning the analysed lakes obtained from the maps was verified on the basis of direct field measurements performed using a GPS RTK receiver. Use was made of georeferential corrections provided by the NAVGEO service or a virtual reference station generated by the ASG EUPOS system. A compilation of cartographic and field data formed the basis for a comparison of the actual area and the length of the shoreline of the studied lakes. Cartographic analyses made it possible to single out the most reliable cartographic sources, which could be used for the purposes of hydrographical analyses. The course of shorelines shows the attached map.
This paper provides analyses of the accuracy and convergence time of the PPP method using GPS systems and different IGS products. The official IGS products: Final, Rapid and Ultra Rapid as well as MGEX products calculated by the CODE analysis centres were used. In addition, calculations with weighting function of the observations were carried out, depending on the elevation angle. The best results were obtained for CODE products, with a 5-minute interval precision ephemeris and precise corrections to satellite clocks with a 30-second interval. For these calculations the accuracy of position determination was at the level of 3 cm with a convergence time of 44 min. Final and Rapid products, which were orbit with a 15-minute interval and clock with a 5 minute interval, gave very similar results. The same level of accuracy was obtained for calculations with CODE products, for which both precise ephemeris and precise corrections to satellite clocks with the interval of 5 minutes. For these calculations, the accuracy was 4 cm with the convergence time of 70 min. The worst accuracy was obtained for calculations with Ultra-rapid products, with an interval of 15 minutes. For these calculations, the accuracy was 10 cm with a convergence time of 120 min. The use of the weighting function improved the accuracy of position determination in each case, except for calculations with Ultra-rapid products. The use of this function slightly increased the convergence time, in addition to the CODE calculation, which was reduced to 9 min.
The paper presents the results of research on the possibilities of fixing ship position coordinates based on results of surveying bearings on navigational marks with the use of the CCD camera. Accuracy of the determination of ship position coordinates, expressed in terms of the mean error, was assumed to be the basic criterion of this estimation. The first part of the paper describes the method of the determination of the resolution and the mean error of the angle measurement, taken with a camera, and also the method of the determination of the mean error of position coordinates when two or more bearings were measured. There have been defined three software applications assigned for the development of navigational sea charts with accuracy areas mapped on. The second part contains the results of studying accuracy in fixing ship position coordinates, carried out in the Gulf of Gdansk, with the use of bearings taken obtained with the Rolleiflex and Sony cameras. The results are presented in a form of diagrams of the mean error of angle measurement, also in the form of navigational charts with accuracy fields mapped on. In the final part, basing on results obtained, the applicability of CCD cameras in automation of coastal navigation performance process is discussed.
A parcel is the most important object of real estate cadastre. Its primary spatial attribute are boundaries, determining the extent of property rights. Capturing the data on boundaries should be performed in the way ensuring sufficiently high accuracy and reliability. In recent years, as part of the project “ZSIN – Construction of Integrated Real Estate Information System – Stage I”, in the territories of the participating districts, actions were taken aimed at the modernization of the register of land and buildings. In many cases, this process was carried out basing on photogrammetric materials. Applicable regulations allow such a possibility. This paper, basing on the documentation from the National Geodetic and Cartographic Documentation Center and on the authors’ own surveys attempts to assess the applicability of the photogrammetric method to capture data on the boundaries of cadastral parcels. The scope of the research, most importantly, included the problem of accuracy with which it was possible to determine the position of a boundary point using photogrammetric surveys carried out on the terrain model created from processed aerial photographs. The article demonstrates the manner of recording this information in the cadastral database, as well as the resulting legal consequences. Moreover, the level of reliability of the entered values of the selected attributes of boundary points was assessed.
According to metrological guidelines and specific legal requirements, every smart electronic electricity meter has to be constantly verified after pre-defined regular time intervals. The problem is that in most cases these pre-defined time intervals are based on some previous experience or empirical knowledge and rarely on scientifically sound data. Since the verification itself is a costly procedure it would be advantageous to put more effort into defining the required verification periods. Therefore, a fixed verification interval, recommended by various internal documents, standardised evaluation procedures and national legislation, could be technically and scientifically more justified and consequently more appropriate and trustworthy for the end user. This paper describes an experiment to determine the effect of alternating temperature and humidity and constant high current on a smart electronic electricity meter’s measurement accuracy. Based on an analysis of these effects it is proposed that the current fixed verification interval could be revised, taking into account also different climatic influence. The findings of this work could influence a new standardized procedure in respect of a meter’s verification interval.
The paper addresses the problem of the automatic distortion removal from images acquired with non-metric SLR camera equipped with prime lenses. From the photogrammetric point of view the following question arises: is the accuracy of distortion control data provided by the manufacturer for a certain lens model (not item) sufficient in order to achieve demanded accuracy? In order to obtain the reliable answer to the aforementioned problem the two kinds of tests were carried out for three lens models. Firstly the multi-variant camera calibration was conducted using the software providing full accuracy analysis. Secondly the accuracy analysis using check points took place. The check points were measured in the images resampled based on estimated distortion model or in distortion-free images simply acquired in the automatic distortion removal mode. The extensive conclusions regarding application of each calibration approach in practice are given. Finally the rules of applying automatic distortion removal in photogrammetric measurements are suggested
Computer-aided tools help in shortening and eradicating numerous repetitive tasks that reduces the gap between digital model and actual product. Use of these tools assists in realizing free-form objects such as custom fit products as described by a stringent interaction with the human body. Development of such a model presents a challenging situation for reverse engineering (RE) which is not analogous with the requirement for generating simple geometric models. Hence, an alternating way of producing more accurate three-dimensional models is proposed. For creating accurate 3D models, point clouds are processed through filtering, segmentation, mesh smoothing and surface generation. These processes help in converting the initial unorganized point data into a 3D digital model and simultaneously influence the quality of model. This study provides an optimum balance for the best accuracy obtainable with maximum allowable deviation to lessen computer handling and processing time. A realistic non trivial case study of free-form prosthetic socket is considered. The accuracy obtained for the developed model is acceptable for the use in medical applications and FEM analysis.
The paper relates to the problem of adaptation of V-block methods to waviness measurements of cylindrical surfaces. It presents the fundamentals of V-block methods and the principle of their application. The V-block methods can be successfully used to measure the roundness and waviness deviations of large cylinders used in paper industry, shipping industry, or in metallurgy. The concept of adaptation of the V-block method to waviness measurements of cylindrical surfaces was verified using computer simulations and experimental work. The computer simulation was carried out in order to check whether the proposed mathematical model and V-block method parameters are correct. Based on the simulation results, a model of measuring device ROL-2 for V-block waviness measurements was developed. Next, experimental research was carried out consisting in evaluation of waviness deviation, initially using a standard non-reference measuring device, and then using the tested device based on the V-block method. Finally, accuracy of the V-block experimental method was calculated.
The article presents the results of a comparative analysis of the metal substructure for dental prosthesis made from a Co-Cr-Mo-W alloy by two techniques, i.e. precision investment casting and selective laser melting (SLM). It was found that the roughness of the raw surface of the SLM sinter is higher than the roughness of the cast surface, which is compensated by the process of blast cleaning during metal preparation for the application of a layer of porcelain. Castings have a dendritic structure, while SLM sinters are characterized by a compact, fine-grain microstructure of the hardness higher by about 100 HV units. High performance and high costs of implementation the SLM technology are the cause to use it for the purpose of many dental manufacturers under outsourcing rules. The result is a reduction in manufacturing costs of the product associated with dental work time necessary to scan, designing and treatment of sinter compared with the time needed to develop a substructure in wax, absorption in the refractory mass, casting, sand blasting and finishing. As a result of market competition and low cost of materials, sinter costs decrease which brings the total costs related to the construction unit making using the traditional method of casting, at far less commitment of time and greater predictability and consistent sinter quality.
This paper presents decision-making risk estimation based on planimetric large-scale map data, which are data sets or databases which are useful for creating planimetric maps on scales of 1:5,000 or larger. The studies were conducted on four data sets of large-scale map data. Errors of map data were used for a risk assessment of decision-making about the localization of objects, e.g. for land-use planning in realization of investments. An analysis was performed for a large statistical sample set of shift vectors of control points, which were identified with the position errors of these points (errors of map data). In this paper, empirical cumulative distribution function models for decision-making risk assessment were established. The established models of the empirical cumulative distribution functions of shift vectors of control points involve polynomial equations. An evaluation of the compatibility degree of the polynomial with empirical data was stated by the convergence coefficient and by the indicator of the mean relative compatibility of model. The application of an empirical cumulative distribution function allows an estimation of the probability of the occurrence of position errors of points in a database. The estimated decision-making risk assessment is represented by the probability of the errors of points stored in the database
Both the growing number of dispersed generation plants and storage systems and the new roles and functions on the demand side (e.g. demand side management) are making the operation (monitoring and control) of electrical grids more complex, especially in distribution. This paper demonstrates how to integrate phasor measurements so that state estimation in a distribution grid profits optimally from the high accuracy of PMUs. Different measurement configurations consisting of conventional and synchronous mea- surement units, each with different fault tolerances for the quality of the calculated system state achieved, are analyzed and compared. Weighted least squares (WLS) algorithms for conventional, linear and hybrid state estimation provide the mathematical method used in this paper. A case study of an 18-bus test grid with real measured PMU data from a 110 kV distribution grid demonstrates the improving of the system’s state variable’s quality by using synchrophasors. The increased requirements, which are the prerequisite for the use of PMUs in the distribution grid, are identified by extensively analyzing the inaccuracy of measurement and subsequently employed to weight the measured quantities.
Power systems that are highly loaded, especially by a stochastic supply of renewables and the presence of storages, require dynamic measurements for their optimal control. Phasor measurement units (PMUs) can be used to capture electrical parameters of a power system. Standards on the PMU dynamic performance have been modified to incorporate their new dynamic mode of operation. This paper examines the PMU dynamic performance and proposes essential algorithms for measurement accuracy verification. Measurements of dynamic input signals, which vary in amplitude or frequency, were taken during automated tests of two PMUs. The test results are presented and expounded with further recommendation for the performance requirements. This paper also presents and examines applied testing procedures with relevance to the specifications of the IEEE Standard for Synchrophasor C37.118.1™-2011 and its amendment C37.118.1a™-2014.
The paper presents the problem of assessing the accuracy of reconstructing free-form surfaces in the CMM/CAD/CAM/CNC systems. The system structure comprises a coordinate measuring machine (CMM) PMM 12106 equipped with a contact scanning probe, a 3-axis Arrow 500 Vertical Machining Center, QUINDOS software and Catia software. For the purpose of surface digitalization, a radius correction algorithm was developed. The surface reconstructing errors for the presented system were assessed and analysed with respect to offset points. The accuracy assessment exhibit error values in the reconstruction of a free-form surface in a range of ± 0.02 mm, which, as it is shown by the analysis, result from a systematic error.
Measurement data obtained from Weigh-in-Motion systems support protection of road pavements from the adverse phenomenon of vehicle overloading. For this protection to be effective, WIM systems must be accurate and obtain a certificate of metrological legalization. Unfortunately there is no legal standard for accuracy assessment of Weigh-in-Motion (WIM) systems. Due to the international range of road transport, it is necessary to standardize methods and criteria applied for assessing such systems’ accuracy. In our paper we present two methods of determining accuracy of WIM systems. Both are based on the population of weighing errors determined experimentally during system testing. The first method is called a reliability characteristic and was developed by the authors. The second method is based on determining boundaries of the tolerance interval for weighing errors. Properties of both methods were assessed on the basis of simulation studies as well as experimental results obtained from a 16-sensor WIM system.
The method of determining the accuracy of polymer molds in plaster forms has been discussed. Distortion of the surface of molds and plaster molds has been assessed. It has been found that the presence of monolithic and porous structure in the samples does not change the accuracy of the surfaces when forms are prepared for removing the material of the model. It has been found that in case of full-mold casting it is more expedient to form the mold cavity with cellular adjustable structures of molding prototypes.
The present work discusses results of increased temperature on shape-dimensional changes of a 110 type hose coupling, produced from EN AC-AlSi11 alloy with the use of pressure die casting technology. The castings were soaked for 3.5 h at temperatures 460°C, 475°C and 490°C. The verification of shape-dimensional accuracy of the elements after soaking treatment, in relation to raw casting, was carried out by comparing the 3D models received from 3D scanning. Soaking temperature of about 460°C-475°C results in no significant changes in the shapes and dimensions of the castings, or surface defects in the form of blisters, which can be seen at a temperature of 490°C.