Search results

Filters

  • Journals
  • Date

Search results

Number of results: 4
items per page: 25 50 75
Sort by:

Abstract

The results of experimental test of nine thickset reinforced concrete slabs in punching are presented in the this paper. The aim of the tests was verifi cation of the Eurocode EC 2 procedure, by which the ultimate shear stresses vRd,c depend on the slenderness of the slab. Besides of the performed tests results, the analysis of the foreign investigation of the fundaments is also included. The test results, as well as other tests, show the correctness of the function assumed in Eurocode 2, which gives correlation between ultimate stresses vRd,c and shear slenderness.
Go to article

Abstract

The paper concerns simulation of fully developed and axially-symmetrical turbulent flow of coarse-dispersive slurry if all solid particles have similar size and shape with particles diameter from 1 mm to 5 mm, solid density from 1045 kg/m^3 to 3000 kg/m^3, and solid concentration by volume from 20% to 40%. The author examines the influence of particle diameter on additional shear stress due to the ‘particles-wall’ interactions for moderate and high solid concentration. The mathematical model was developed using Bagnold's concept, [26] and assumes that the total wall shear stresses are equal to the sum of ‘liquid-wall’ and ‘particles-wall’ shear stresses. The mathematical model was successfully verified with own measurements of frictional head loss in vertical coarse - dispersive slurry flow, named: ‘sand-water’, ‘polystyrene-water’ and ‘pvc-water’, [10], [26]. The mathematical model can predict ‘particles-wall’ shear stress, pressure drop and friction factor for coarse-dispersive turbulent slurry flow in a pipe, [10]. The aim of the paper is to present qualitative and quantitative dependence of solid particle diameter, solid particle density, solid concentration, and Reynolds number for carrier liquid phase on the ‘particles-wall’ shear stress. It is demonstrated that the solid particle diameter plays crucial role in its dependence on the ‘particles-wall’ shear stress. It was proved that in particular flow conditions the ‘particles-wall’ shear stress is much higher compared to the carrier liquid wall shear stress.
Go to article

Abstract

Two types of submerged membrane bioreactors (MBR): hollow fiber (HF) and hollow sheet (HS), have been studied and compared in terms of energy consumption and average shear stress over the membrane wall. The analysis of energy consumption was made using the correlation to determine the blower power and the blower power demand per unit of permeate volume. Results showed that for the system geometries considered, in terms the of the blower power, the HF MBR requires less power compared to HS MBR. However, in terms of blower power per unit of permeate volume, the HS MBR requires less energy. The analysis of shear stress over the membrane surface was made using computational fluid dynamics (CFD) modelling. Experimental measurements for the HF MBR were compared with the CFD model and an error less that 8% was obtained. For the HS MBR, experimental measurements of velocity profiles were made and an error of 11% was found. This work uses an empirical relationship to determine the shear stress based on the ratio of aeration blower power to tank volume. This relationship is used in bubble column reactors and it is extrapolate to determine shear stress on MBR systems. This relationship proved to be overestimated by 28% compared to experimental measurements and CFD results. Therefore, a corrective factor is included in the relationship in order to account for the membrane placed inside the bioreactor.
Go to article

Abstract

This paper presents an elasticity solution of adhesive tubular joints in laminated composites, with axial symmetry. In this model, adherends are orthotropic shells and the stacking sequences can be either symmetric or asymmetric. Adhesive layer is homogenous and made of isotropic material. They are modelled as continuously distributed tension/compression and shear springs. Employing constitutive, kinematics and equilibrium equations, sets of differential equations for each inside and outside of overlap zones are obtained. By solving these equations, shear and peel stresses in adhesive layer(s), as well as deflections, stress resultants and moment resultants in the adherends are determined. It is seen that the magnitude of peel stresses due to transverse shear stress resultant is much greater than that obtained from axial stress resultant. The developed results are compared with those obtained by finite element analysis using ANSYS software. The comparisons demonstrate the accuracy and effectiveness of the aforementioned methods.
Go to article

This page uses 'cookies'. Learn more