Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 4
items per page: 25 50 75
Sort by:

Abstract

The analysis of changes in the mechanical properties of wooden mining cribs under the influence of different types of exploitation loads is the question for which deals with many domestic and abroad research centers deal with. High The high interest in this subject results from the increase of the conducted depth exploitation, which contributes to the increase in both the vertical pres-sure and the complexity of geological – mining conditions and in- the intensification of natural hazards. Another reason is the tendency of decreasing the thickness of the exploited ores deposits. Wooden crib support is used Both both in underground ore, hard coal and salt mining is used wooden crib support. Mining cribs with various configurations are especially useful for the reinforcement of excavations workings behind the front and for further strengthen of the crossings. In particular, additional reinforcement support in the form of wooden cribs (pile supporting), which shall be left empty or filled with waste rock is applied in the ore mining in places where found extended rooms or drifts are found or in places with degraded roof conditions, applies additional reinforcement support in the form of wooden cribs (pile supporting), which shall be left empty or filled with waste rock. During underground ex-ploitation is produced waste Waste rock, which comes from the access, prepar-atory excavations and from ongoing field of exploitation is produced during underground exploitation. In the case of the underground exploitation of cop-per ore, waste rock is used to fill voids after exploitation as rock stowing. It is also used for filling mining wooden cribs, as an artificial support and for harder transportation roads. This paper presents the results of the laboratory strength tests performed on models of four-point timber cribs, built with beams set horizontally, at the ge-ometrical scale of 1:10. In the laboratory research Research wooden cribs models with size 200 × 200 × 200 mm and 100 × 100 × 100 mm were used in the laboratory. The paper describes the maximum loading capacity of the cribs consisted consisting only of beams and filled with waste rocks. In addition, a vertical and appropriate strain of cribs at maximum force was shown. On the basis of laboratory research it was found that the use of the same number of timbers and the management of waste rocks, the filling of the four-point cribs with the waste rocks allowed several times to increase its support to be increased several times.
Go to article

Abstract

The methane hazard is one of the most dangerous phenomena in hard coal mining. In a certain range of concentrations, methane is flammable and explosive. Therefore, in order to maintain the continuity of the production process and the safety of work for the crew, various measures are taken to prevent these concentration levels from being exceeded. A significant role in this process is played by the forecasting of methane concentrations in mine headings. This very problem has been the focus of the present article. Based on discrete measurements of methane concentration in mine headings and ventilation parameters, the distribution of methane concentration levels in these headings was forecasted. This process was performed on the basis of model-based tests using the Computational Fluid Dynamics (CFD). The methodology adopted was used to develop a structural model of the region under analysis, for which boundary conditions were adopted on the basis of the measurements results in real-world conditions. The analyses conducted helped to specify the distributions of methane concentrations in the region at hand and determine the anticipated future values of these concentrations. The results obtained from model-based tests were compared with the results of the measurements in realworld conditions. The methodology using the CFD and the results of the tests offer extensive possibilities of their application for effective diagnosis and forecasting of the methane hazard in mine headings.
Go to article

Abstract

This paper constitutes the sensitivity study of application the Polar WRF model to the Svalbard area with testing selected parameterizations, including planetary boundary layer, radiation and microphysics schemes. The model was configured, using three one-way nested domains with 27 km, 9 km and 3 km grid cell resolutions. Results from the innermost domain were presented and compared against measured wind speed and air temperature at 10 meteorological stations. The study period covers two months: June 2008 and January 2009. Significant differences between simulations results occurred for planetary boundary layer (PBL) schemes in January 2009. The Mellor-Yamada-Janjic (MYJ) planetary boundary layer (PBL) scheme resulted in the lowest errors for air temperature, according to mean error (ME), mean absolute error (MAE) and correlation coefficient values, where for wind speed this scheme was the worst from all the PBL schemes tested. In the case of June 2008, shortwave and longwave radiation schemes influenced the results the most. Generally, higher correlations were obtained for January, both for air temperature and wind speed. However, the model performs better for June in terms of ME and MAE error statistics. The results were also analyzed spatially, to summarize the uncertainty of the model results related to the analyzed parameterization schemes groups. Significant variability among simulations was calculated for January 2009 over the northern part of Spitsbergen and fjords for the PBL schemes. Standard deviations for monthly average simulated values were up to 3.5°C for air temperature and around 1 m s-1 for wind speed.
Go to article

Abstract

Experiments of filling the model moulds cavity of various inner shapes inserted in rectangular cavity of the casting die (dimensions: 280 mm (height) x 190 mm (width) x 10 mm (depth) by applying model liquids of various density and viscosity are presented in the paper. Influence of die venting as well as inlet system area and inlet velocity on the volumetric rate of filling of the model liquid – achieved by means of filming the process in the system of a cold-chamber casting die was tested. Experiments compared with the results of simulation performed by means of the calculation module Novacast (Novaflow&Solid) for the selected various casting conditions – are also presented in the paper.
Go to article

This page uses 'cookies'. Learn more