The article discusses the weldment to casting conversion process of rocker arm designed for operation in a special purpose vehicle to obtain a consistency of objective functions, which assume the reduced weight of component, the reduced maximum effort of material under the impact of service loads achieved through topology modification for optimum strength distribution in the sensitive areas, and the development of rocker arm manufacturing technology. As a result of conducted studies, the unit weight of the item was reduced by 25%, and the stress limit values were reduced to a level guaranteeing safe application.
The article describes the optimization of the melting brass. Brasses, as one of the most popular alloys of copper, deserve special attention in the context of the processes of melting, which in turn would provide not only products of better quality, but also reduce the cost of their production or refining. For this purpose, several studies carried out deriatographic (DTA) and thermogravimetric (TG) using derivatograph. The results were confronted with the program SLAG - PROP used to evaluate the physicochemical properties of the coatings extraction. Based on the survey and analysis of the program can identify the most favorable physico - chemical properties, which should be carried out treatments. This allows for slag mixtures referred configurations oxide matrix containing specific stimulators of the reaction. Conducted empirical studies indicate a convergence of the areas proposed by the application. It should also be noted that the program also indicates additional areas in which to carry out these processes would get even better, to optimize the melting process, the results.
It has been found that the area where one can look for significant reserves in the procurement logistics is a rational management of the stock of raw materials. Currently, the main purpose of projects which increase the efficiency of inventory management is to rationalise all the activities in this area, taking into account and minimising at the same time the total inventory costs. The paper presents a method for optimising the inventory level of raw materials under a foundry plant conditions using two different control models. The first model is based on the estimate of an optimal level of the minimum emergency stock of raw materials, giving information about the need for an order to be placed immediately and about the optimal size of consignments ordered after the minimum emergency level has occurred. The second model is based on the estimate of a maximum inventory level of raw materials and an optimal order cycle. Optimisation of the presented models has been based on the previously done selection and use of rational methods for forecasting the time series of the delivery of a chosen auxiliary material (ceramic filters) to a casting plant, including forecasting a mean size of the delivered batch of products and its standard deviation
The paper undertakes an important topic of evaluation of effectiveness of SCADA (Supervisory Control and Data Acquisition) systems, used for monitoring and control of selected processing parameters of classic green sands used in foundry. Main focus was put on process studies of properties of so-called 1st generation molding sands in the respect of their preparation process. Possible methods of control of this processing are presented, with consideration of application of fresh raw materials, return sand (regenerate) and water. The studies conducted in one of European foundries were aimed at pointing out how much application of new, automated plant of sand processing incorporating the SCADA systems allows stabilizing results of measurement of selected sand parameters after its mixing. The studies concerned two comparative periods of time, before an implementation of the automated devices for green sands processing (ASMS - Automatic Sand Measurement System and MCM – Main Control Module) and after the implementation. Results of measurement of selected sand properties after implementation of the ASMS were also evaluated and compared with testing studies conducted periodically in laboratory.
A comparative analysis involving the evaluation of the effectiveness of investment projects can be based on various rules indicating selection of the most favorable decisions. The dynamic methods for assessment of investment projects discussed in this article, which consider the possibility of modifying the predetermined investment options, are quite complex and difficult to implement. They are used both in the construction phase of the new company, as well as in its subsequent modernization. The assessments should be characterized by a high coefficient of the economic efficiency. The, observed in practice, high dynamic variability of both the external and internal conditions under which the company operates is the reason why in the process of calculating the economic efficiency of investment projects, there is a significant number of random parameters affected by high uncertainty and risk. Investments in the metallurgical industry are characterized by a relatively long cycle of implementation and operation. These are capital-intensive projects and often mistakenly taken investment decisions end in failure of the investment project and, consequently, in the collapse of the company. In addition, the applied methods of risk assessment of investment projects, especially the dynamic ones, should be fully understood by managerial staff and constitute an easy to use, yet accurate tool for improving the efficiency of the company.
Conducting reliable and credible evaluation and statistical interpretation of empirical results related to the operation of production systems in foundries is for most managers complicated and labour-intensive. Additionally, in many cases, statistical evaluation is either ignored and considered a necessary evil, or is completely useless because of improper selection of methods and subsequent misinterpretation of the results. In this article, after discussing the key elements necessary for the proper selection of statistical methods, a wide spectrum of these methods has been presented, including regression analysis, uni- and multivariate correlation, one-way analysis of variance for factorial designs, and selected forecasting methods. Each statistical method has been illustrated with numerous examples related to the foundry practice.
The objective of studies presented in this publication was structuring of research knowledge about the ADI functional properties and changes in these properties due to material treatment. The results obtained were an outcome of research on the selection of a format of knowledge representation that would be useful in further work aiming at the design, application and implementation of an effective system supporting the decisions of a technologist concerning the choice of a suitable material (ADI in this case) and appropriate treatment process (if necessary). ALSV(FD) logic allows easy modelling of knowledge, which should let addressees of the target system carry out knowledge modelling by themselves. The expressiveness of ALSV (FD) logic allows recording the values of attributes from the scope of the modelled domain regarding ADI, which is undoubtedly an advantage in the context of further use of the logic. Yet, although the logic by itself does not allow creating the rules of knowledge, it may form a basis for the XTT format that is rule-based notation. The difficulty in the use of XTT format for knowledge modelling is acceptable, but formalism is not suitable for the discovery of rules, and therefore the knowledge of technologist is required to determine the impact of process parameters on values that are functional properties of ADI. The characteristics of ALSV(FD) logic and XTT formalism, described in this article, cover the most important aspects of a broadly discussed, full evaluation of the applicability of these solutions in the construction of a system supporting the decisions of a technologist.