Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 2195
items per page: 25 50 75
Sort by:

Abstract

A hybrid artificial boundary condition (HABC) that combines the volume-based acoustic damping layer (ADL) and the local face-based characteristic boundary condition (CBC) is presented to enhance the absorption of acoustic waves near the computational boundaries. This method is applied to the prediction of aerodynamic noise from a circular cylinder immersed in uniform compressible viscous flow. Different ADLs are designed to assess their effectiveness whereby the effect of the mesh-stretch direction on wave absorption in the ADL is analysed. Large eddy simulation (LES) and FW-H acoustic analogy method are implemented to predict the far-field noise, and the sensitivities of each approach to the HABC are compared. In the LES computed propagation field of the fluctuation pressure and the frequency-domain results, the spurious reflections at edges are found to be significantly eliminated by the HABC through the effective dissipation of incident waves along the wave-front direction in the ADL. Thereby, the LES results are found to be in a good agreement with the acoustic pressure predicted using FW-H method, which is observed to be just affected slightly by reflected waves.
Go to article

Abstract

The new investigation method of the kinetics of the gas emission from moulding sands used for moulds and cores is presented in this paper. The gas evolution rate is presented not only as a function of heating time but also as a function of instantaneous temperatures. In relation to the time and heating temperature the oxygen and hydrogen contents in evolving gases was also measured. This method was developed in the Laboratory of Foundry Moulds Technology, Faculty of Foundry Engineering, AGH. Gas amounts which are emitted from the moulding sand at the given temperature recalculated to the time unit (kinetics) are obtained in investigations. Results of investigations of moulding sand with furan resin are presented - as an example - in the paper.
Go to article

Abstract

At thermal junctions of aluminium alloy castings and at points where risering proves to be difficult there appear internal or external shrinkages, which are both functionally and aesthetically inadmissible. Applying the Probat Fluss Mikro 100 agent, which is based on nano-oxides of aluminium, results in the appearance of a large amount of fine microscopic pores, which compensate for the shrinking of metal. Experimental tests with gravity die casting of AlSi8Cu3 and AlSi10Mg alloys have confirmed that the effect of the agent can be of advantage in foundry practice, leading to the production of castings without local concentrations of defects and without the appearance of shrinkages and macroscopic gas pores. Also, beneficial effect on the mechanical properties of the metal has been observed.
Go to article

Abstract

The obtained results of heating of sand moulds with binders by means of a thermal radiation of liquid metal are presented in this study. Standard samples for measuring Rg made of the tested moulding sands were suspended at the lower part of the cover which was covering the crucible with liquid metal (cast iron), placed in the induction furnace. The authors own methodology was applied in investigations. The progressing of the samples surface layers heating process was determined as the heating time function. Samples of a few kinds of moulding sands with chemical binders were tested. Samples without protective coatings as well as samples with such coatings were tested. The influence of the thermal radiation on bending resistance of samples after their cooling was estimated. The influence of several parameters such as: time of heating, distance from the metal surface, metal temperature, application of coatings, were tested. A very fast loss of strength of moulding sands with organic binders was found, especially in cases when the distance between metal and sample surfaces was small and equaled to 10÷15 mm. Then, already after app. 15 seconds of the radiation (at Tmet=1400o C), the resistance decreases by nearly 70%. Generally, moulding sands with organic binders are losing their strength very fast, while moulding sands with water glass at first increase their strength and later slightly lose. The deposition of protective coatings increases the strength of the mould surface layers, however does not allow to retain this strength after the metal thermal radiation.
Go to article

Abstract

Abstract The influence of selected factors on drying ceramic moulds applied in the investment casting technology was determined by the gravimetric method. Moulds produced of ceramic sands based on the new generation binders - colloidal silica, were investigated. It was found that each successive layer, of a similar thickness, is drying longer than the previous one. The drying time of layers forming closed spaces is several times longer as compared with drying open surfaces (external). Grain size of matrix used for moulds sprinkling has none significant influence on drying rates.
Go to article

Abstract

The results of investigations of the granulation process of foundry dusts generated in the dry mechanical reclamation process of used sands, where furan resins were binders are presented in the paper. Investigations concerned producing of granules of the determined dimensions and strength parameters. Granules were formed from the dusts mixture consisting in 50 mass% of dusts obtained after the reclamation of the furane sands and in 50 mass % of dusts from sands with bentonite. Dusts from the bentonite sands with water were used as a binder allowing the granulation of after reclamation dusts from the furane sands. The following parameters of the ready final product were determined: moisture content (W), shatter test of granules (Wz) performed directly after the granulation process and after 1, 3, 5, 10 days and nights of seasoning, water-resistance of granules after 24 hours of being immersed in water, surface porosity ep and volumetric porosity ev. In addition the shatter test and water-resistance of granulate dried at a temperature of 105oC were determined. Investigations were performed at the bowl angle of inclination 45o, for three rotational speeds of the bowl being: 10, 15, 20 rpm. For the speed of 10 rpm the granulation tests of dusts mixture after the preliminary mixing in the roller mixer and with the addition of water-glass in the amount of 2% in relation to the amount of dust were carried out. The obtained results indicate that the granulator allows to obtain granules from dusts originated from the reclamations of moulding sands with the furane resin with an addition of dusts from the bentonite sands processing plants.
Go to article

Abstract

A technology of sands with water glass hardened by liquid esters is a cheap and ecologic method of producing moulding sands. Due to these advantages, this technology is still very important in several foundry plants for production of heavy iron and steel castings. Reclamation of the mixed moulding and core sands generates significant amounts of dusts, which require further treatments for their reuse. The results of investigations of a pressureless granulation of dusts generated in the dry mechanical reclamation process of the mixture consisting in app. 90 % of moulding sands from the Floster S technology and in 10 % of core sands with phenolic resin resol type, are presented in the hereby paper. Investigations were aimed at obtaining granulates of the determined dimensional and strength parameters. Granules were formed from the mixture of dusts consisting of 75 mass% of dusts after the reclamation of sands mixture and of 25 mass% of dusts from bentonite sands processing plant. Wetted dusts from bentonite sands were used as a binding agent allowing the granulation of after reclamation dusts originated from the mixed sands technology.
Go to article

This page uses 'cookies'. Learn more