In this work, three ceramic composite coatings Al2O3-3TiO2 C, Al2O3-13TiO2 C, and Al2O3-13TiO2 N were plasma sprayed on steel substrates. They were deposited with two conventional powders differing the volume fraction of TiO2 and nanostructured powder. The mechanical and tribological properties of the coatings were investigated and compared. The increase in TiO2 content from 3 wt.% to 13 wt.% in the conventional feedstock improved the mechanical properties and abrasion resistance of coatings. However, the size of the used powder grains had a much stronger influence on the properties of deposited coatings than the content of the titania phase. The Al2O3-13TiO2 coating obtained from nanostructured powder revealed significantly better properties than that plasma sprayed using conventional powder, i.e. 22% higher microhardness, 19% lower friction coefficient, and over twice as good abrasive wear resistance. In turn, the Al2O3-13TiO2 conventional coating showed an increase in microhardness and abrasive wear resistance, 36% and 43%, respectively, and 6% higher coefficient of friction compared to the Al2O3-3TiO2 conventional coating.
The article is devoted to personal nouns with suffi x -ant in Polish and Belarusian. The lexical and semantic analysis of the studied group of words showed that in both languages they belong to the literary variety of language, however, numerous nouns represent rare vocabulary, sometimes characterized stylistically. The overwhelming majority of names defi nes the names of active contractors of activities, less often – passive contractors, and least frequently – names of owners. In addition, the nomina masculina with suffi x -ant belong to the attributive names, defi ning people on the basis of their character traits, tendencies, and often vices. The s tudied lexis include archaic or colloquial derivatives. Among the specialist words, there were examples representing such fi elds as law and judiciary, economics and trade, religion and art, education and science.
Paper presents the results of evaluation of heat resistance and specific heat capacity of MAR-M-200, MAR-M-247 and Rene 80 nickel superalloys. Heat resistance was evaluated using cyclic method. Every cycle included heating in 1100°C for 23 hours and cooling for 1 hour in air. Microstructure of the scale was observed using electron microscope. Specific heat capacity was measured using DSC calorimeter. It was found that under conditions of cyclically changing temperature alloy MAR-M-247 exhibits highest heat resistance. Formed oxide scale is heterophasic mixture of alloying elements, under which an internal oxidation zone was present. MAR-M-200 alloy has higher specific heat capacity compared to MAR-M-247. For tested alloys in the temperature range from 550°C to 800°C precipitation processes (γ′, γ′′) are probably occurring, resulting in a sudden increase in the observed heat capacity.
Eyespot is one of the most important fungal diseases of the stem base of wheat (Triticum aestivum L.). The presented study clearly demonstrated that the Pch1 gene was the main effective source for reducing the eyespot disease score in the analyzed winter wheat lines. Nevertheless, Pch1 was present only in 8−9% of the investigated lines. Using an isoenzymatic marker and molecular markers, the presence of the Pch1 gene and lack of the Pch2 gene was identified in six lines. Two lines, SMH 9409 and DL 358/13/4, were polymorphic in an isoenzymatic marker study. In the remaining three lines, C 3373/11-1, KBH 15.15 and KBP 1416, the Pch1 gene was identified only with the use of an isoenzymatic marker. Both genes Pch1 and Pch2, as well as the resistant variety Rendezvous, were found in three lines: DD 248/12, KBP 15.2 and STH 4431. In line DD 708/13, the presence of the Pch1 and Pch2 genes was identified, where the association between the Pch1 and the locus of the Xorw5 marker was broken. It was shown that the presence or absence of Pch1 and Pch2 genes did not significantly affect the grain yield (from the plot), although the yield was highest in the presence of both genes. A significant effect of the presence of the Pch1 gene on thousand kernel weight (TKW) was observed. Lines with the Pch1 gene showed significantly higher TKW values than lines without both genes or with the Pch2 gene only.
This paper presents the study of microstructure and properties of 8 mol% yttrium stabilized zirconia coating fabricated by Plasma Spray Physical Vapor Deposition technique on commercial pure titanium. The coating was characterized by X-ray diffraction, high resolution scanning electron microscope, profilometer, nanoindentation and nanomachining tests. The X-ray phase analysis exhibit the tetragonal Zr0.935Y0.065O1.968, TiO and α-Ti phases. The Rietveld refinement technique were indicated the changes of crystal structure of the produced coatings. The characteristic structure of columns were observed in High Resolutions Scanning Electron Microscopy. Moreover, the obtained coating had various development of surfaces, thickness was equal to 3.1(1) µm and roughness 0.40(7) µm. Furthermore, the production coatings did not show microcracks, delamination and crumbing. The performed experiment encourages carried out us to tests for osseointegration.