Phosphorothioate CpG oligodeoxynucleotides (ODN) are reported to be recognized by the membrane-bound TLR9 and trigger the MyD88-dependent up-regulation of Type I interferons and pro-inflammatory cytokines. Whether plasmids containing multiple CpG motifs stimulate the same signaling pathway is yet to be determined. The present results show that the CpG motifs enrich plasmid pUC18-CpG stimulates RAW 264.7 in vitro, mainly through the TBK1-mediated signaling pathway, causing the up-regulation of IFN-β, and pro-inflammatory cytokines TNF-α and IL-6. When pUC18-CpG is co-administered with the recombinant Echinococcus granulosus antigen, the antigen-specific antibody titers are markedly increased compared to the Quil-A adju- vanted group. Antigen specific cytokine quantification shows that cytokine profiles from the pUC18-CpG adjuvanted-group are switched to a Th1-biased immune response.
In the current study, twenty lambs, aged 4 months, half male and half female, were classified into four groups, with five in each group. The experimental three groups of lambs were given intravenous (IV), intramuscular (IM) and subcutaneous (SC) administrations of recombinant ovine interferon-τ (roIFN-τ). The fourth group (normal control) of lambs was given normal saline injections in the same way. After administrations, blood samples were collected from the tested animals at different time points post injection, and the serum titers of roIFN-τ were measured using cytopathic effect (CPE) inhibition bioassay. The results of calculating pharmacokinetic (PK) parameters using DAS software showed that the PK characteristics of roIFN-τ through IV injection conformed to the two-compartment open model, whose half-life of distribution phases (T1/2α) was 0.33±0.034 h and the elimination half-life(T1/2β) was 5.01±0.24 h. However, the PK features of IM injection and SC injection of roIFN-τ conformed to the one compartment open model, whose Tmax were 3.11±0.26 h and 4.83±0.43 h, respectively, together with an elimination half life(T1/2β) of 9.11±0.76 h and 7. 43±0.58 h, and an absorption half-life (T1/2k(a)) of 1.13±0.31 h and 1.85±0.40 h, respectively. The bioavailability of roIFN-τ after IM administration reaches 73.57%, which is greater than that of SC administration (53.43%). These results indicate that the drug administration effect can be preferably obtained following a single dose IM administration of the roIFN-τ aqueous preparation. This study will facilitate the clinical application of roIFN-τ as a potential antiviral agent in future work.
An integrated Z-source inverter for the single-phase single-stage grid-connected photovoltaic system is proposed in this paper. The inverter integrates three functional blocks including maximum-power-point-tracking, step-up/down DC-side voltage and output grid-connected current. According to the non-minimum-phase characteristic presented in DC-side and the functional demands of the system, two constant-frequency sliding-mode controllers with integral compensation are proposed to guarantee the system robustness. By using two controllers, the effects caused by the non-minimum-phase characteristic are mitigated. Under the circumstance of that the input voltage or the grid-connected current changes suddenly, the notches/protrusions following the over-shoot/ under-shoot of the DC-bus voltage are eliminated. The quality of grid-connected current is ensured. Also, a small-signal modelling method is employed to analyze the close-loop system. A 300W prototype is built in the laboratory. A solar-array simulator (SAS) is used to verify the systematic responses in the experiment. The correctness and validity of the inverter and proposed control algorithm are proved by simulation and experimental results.
The friction and wear properties of 201HT aluminum alloys and the corresponding competitive coupons were tested on an electrohydraulic servo face friction and wear testing machine (MM-U10G). The microstructures of the competitive coupons were investigated by scanning electron microscopy (SEM) and consequently the corresponding friction and wear mechanisms were studied. The results demonstrated that: (1) the best competitive material of friction and wear performance of the 201HT was the 201HTC. (2) the 201HTC modified by carbon following the initial mill for oil storage of the micro-groove to be produced, increased the corresponding lubrication performance reduced the friction coefficient and wear rate effectively. (3) the 201HT-201HTC could obtain both better friction and wear mainly due to the initial process of grinding following the 201HT plastic deformation occurred in the surface and the formation of a series of re-melting welding points, whereas the 201HT material hardness would be similar to the 201HTC material hardness, which led into the competitive material friction and wear performance improvement.
Geomechnical model testing has been widely applied as a kind of research technique in underground engineering problems. However, during the practical application process, due to the influence of many factors, the desired results cannot be obtained. In order to solve this problem, based on the measurement requirements of the model test, combined with FBG(Fiber Bragg Grating) sensor technology and traditional measurement methods, an FBG monitoring system, Micro-multi-point displacement test system, resistance strain test system and surrounding rock pressure monitoring system are developed. Applying the systems to a model test of the tunnel construction process, the displacement in advance laws of tunnel face, radial displacement distribution laws and surrounding rock pressure laws are obtained. Test results show that a multivariate information monitoring system has the advantage of high precision, stability and strong anti-jamming capability. It lays a solid foundation for the real-time data monitoring of the tunnel construction process model test.
A novel phase shift full bridge (PSFB) converter with voltage-doubler and decoupling integrated magnetics in photovoltaic (PV) systems is proposed. Considering the demand that the output voltage is higher than the input voltage in PV systems, the voltage-doubler is added to achieve higher voltage gain compared with the traditional PSFB. In order to avoid current oscillation caused by the voltage-doubler and obtain the wide zero voltage switching (ZVS) ranges, an external inductor is imposed on the circuit. Especially, to obtain much higher power density, the external inductor and transformer are integrated into one magnetic core. The operation and voltage gain of proposed converter are analyzed. Also, in order to reveal the effects the integrated magnetics gives to the converter, the decoupling condition and the expression of leakage inductor of integrated magnetics are obtained in detail. Finally a 100 W prototype converter is made and the experimental results are given to verify the analysis.
Sapelovirus A (SV-A) is a positive-sense single-stranded RNA virus which is associated with acute diarrhea, pneumonia and reproductive disorders. The virus capsid is composed of four proteins, and the functions of the structural proteins are unclear. In this study, we expressed SV-A structural protein VP1 and studied its antigenicity and immunogenicity. SDS-PAGE analysis revealed that the target gene was expressed at high levels at 0.6 mM concentration of IPTG for 24 h. The mouse polyclonal antibody against SV-A VP1 protein was produced and reached a high antiserum titer (1: 2,048,000). Immunized mice sera with the recombinant SV-A VP1 protein showed specific recognition of purified VP1 protein by western blot assay and could recognize native SV-A VP1 protein in PK-15 cells infected with SV-A by indirect immunofluorescence assay. The successfully purified recombinant protein was able to preserve its antigenic determinants and the generated mouse anti-SV-A VP1 antibodies could recognize native SV-A, which may have the potential to be used to detect SV-A infection in pigs.