Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 7
items per page: 25 50 75
Sort by:

Abstract

In this article, the authors present a model and a method of determining thermal parameters of a single point of the thermal touch screen for the blind and thermal parameters of selected parts of a human hand. Blind people, by using this device can “see” a pattern of dots by feeling hot spots. The thermal touch screen for the blind was used as a calorimeter and enables to calculate the amount of heat provided to a finger at a temperature ranging from 8°C to 52°C, that is the full range of temperature detected by humans. The authors designated thermal conductivity and heat capacity of both Peltier micromodule and parts of the user's hand. Results of the presented research allow optimizing the construction of the thermal touch screen for the blind and may be helpful for thermal modelling of the human body.
Go to article

Abstract

By simulating the actual working conditions of a cable, the temperature variation rule of different measuring points under different load currents was analyzed. On this basis, a three-dimensional finite element model (FEM) was established, and the difference and influence factors between the simulation temperature and the experimental measured value were discussed, then the influence of thermal conductivity on the operating temperature of the conductor layer was studied. Finally, combined with the steady-state thermal conductivity model and the experimental measured data, the relation between thermal conductivity and load current was obtained.
Go to article

Abstract

Development and demography of Adalia decempunctata L. were studied under laboratory conditions at seven constant temperatures (12, 16, 20, 24, 28, 32 and 36°C). First instar larvae failed to develop to second instar at 12°С and no development occurred at 36°C. The total developmental time varied from 47.92 days at 16°C to 15.94 days at 28°C and increased at 32°C. The lower temperature thresholds of 11.05 and 9.90°C, and thermal constants of 290.84 day-degree and 326.34 day-degree were estimated by traditional and Ikemoto-Takai linear models, respectively. The lower temperature threshold (Tmin) values estimated by Analytis, Briere-1, Briere-2 and Lactin-2 for total immature stages were 11.99, 12.24, 10.30 and 10.8°C, respectively. The estimated fastest developmental temperatures (Tfast) by the Analytis, Briere-1, Briere-2 and Lactin-2 for overall immature stages development of A. decempunctata were 31.5, 31.1, 30.7 and 31.7°C, respectively. Analytis, Briere-1, Briere-2 and Lactin-2 measured the upper temperature threshold (Tmax) at 33.14, 36.65, 32.75 and 32.61°C. The age-stage specific survival rate (sxj) curves clearly depicted the highest and lowest survival rates at 16 and 32°C for males and females. The age-specific fecundity (mx) curves revealed higher fecundity rate when fed A. gossypii at 24 and 28°C. The highest and lowest values of intrinsic rate of increase (r) were observed at 28 and 16°C (0.1945 d–1 and 0.0592 d–1, respectively). Also, the trend of changes in the finite rate of increase (λ) was analogous with intrinsic rate of increase. The longest and shortest mean generation time (T) was observed at 16 and 28°C, respectively and the highest net reproductive rates (R0) was estimated at 24 and 28°C. According to the results, the most suitable temperature seems to be 28°C due to the shortest developmental time, highest survival rate, and highest intrinsic rate of increase.
Go to article

Abstract

In the paper the problem of modelling thermal properties of semiconductor devices with the use of compact models is presented. This class of models is defined and their development over the past dozens of years is described. Possibilities of modelling thermal phenomena both in discrete semiconductor devices, monolithic integrated circuits, power modules and selected electronic circuits are presented. The problem of the usefulness range of compact thermal models in the analysis of electronic elements and circuits is discussed on the basis of investigations performed in Gdynia Maritime University.
Go to article

Abstract

The article presents numerical analysis of the portion of concrete airport pavement that consists of two concrete panels connected with dowels, subjected to thermal and service loads, in terms of changes in base rigidity, plate thickness and diameters, and spacing of dowels. Modifications of the thickness of the plates, diameter and spacing of dowels, and base rigidity were considered by assessing the level of stress and displacement in the analysed concrete plate, as well as normal and tangential stresses in dowels by using finite element method. On the basis of an analysis of examples, an optimal solution of dowelling connections in concrete plates with established loads was proposed. The results of the calculations were presented as a contour level distributions and comparison tables.
Go to article

Abstract

Percutaneous RF ablation is one of alternative treatment for non-surgical liver tumors. Ablative changes in hepatic tissue can be successfully estimated using the finite element method. The authors created a 3D model of a multi-tine applicator immersed in liver tissue, and then determined the optimal values of voltage applied to such an RF electrode, which do not exceed the therapeutic temperature range valid during thermal ablation procedure. Importantly, the simulations were carried out for the RF electric probes with 2 to 5 evenly spaced arms. Additionally, the thermal damage of hepatic tissue for multi-armed applicators working at pre-defined limit values of voltages was established based on the Arrhenius model.
Go to article

Abstract

The paper examines from the thermodynamic point of view operation of coal fired power unit cooperating with the cryogenic oxygen unit, with a particular emphasis on the characteristic performance parameters of the oxygen unit. The relatively high purity technical oxygen produced in the oxygen unit is then used as the oxidant in the fluidized bed boiler of the modern coal fired power unit with electric power output of approximately 460 MW. The analyzed oxygen unit has a classical two-column structure with an expansion turbine (turboexpander), which allows the use of relatively low pressure initially compressed air. Multivariant calculations were performed, the main result being the loss of power and efficiency of the unit due to the need to ensure adequate driving power to the compressor system of the oxygen generating plant.
Go to article

This page uses 'cookies'. Learn more