Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 12
items per page: 25 50 75
Sort by:

Abstract

The paper presents the results of simulation tests of hydraulic resistance and temperature distribution of the prototype Stirling alpha engine supplied with waste heat. The following elements were analyzed: heater, regenerator and cooler. The engine uses compressed air as a working gas. Analyses were carried out for three working pressure values and different engine speeds. The work was carried out in order to optimize the configuration of the engine due to the minimization of hydraulic resistance, while maintaining the required thermal capacity of the device. Preliminary tests carried out on the real object allowed to determine boundary and initial conditions for simulation purposes. The simulation assumes that there is no heat exchange between the regenerator and the environment. The solid model used in simulation tests includes the following elements: supply channel, heater, regenerator, cooler, discharge channel. Due to the symmetrical structure of the analyzed elements, simulation tests were carried out using 1/6 of the volume of the system.
Go to article

Abstract

Theoretical and experimental research indicates that radial loads have a significant influence on the value of belt-on-idler rolling resistances. Computational models discussed in literature use the notion of unit rolling resistance, i.e. rolling resistance per unit length of the idler. The total value of the rolling resistance of belt on a single idler is determined by integrating unit rolling resistance with respect to the length of the contact zone between the belt and the idler. This procedure requires the knowledge of normal load distribution along the contact zone between the belt and the idler. Loads acting on the idler set have been the object of both theoretical analyses and laboratory tests. Literature mentions several models which describe the distribution of normal loads along the contact zone between the belt and the idler set (Krause & Hettler, 1974; Lodewijks, 1996; Gładysiewicz, 2003; Jennings, 2014). Numerous experimental tests (Gładysiewicz & Kisielewski, 2017; Król, 2017; Król & Zombroń, 2012) demonstrated that the resultant normal loads acting on idlers are approximate to the loads calculated in theoretical models. If the resultant normal load is known, it is possible to assume the distribution of loads acting along the contact zone between the belt and the idler. This paper analyzes various hypothetical load distributions calculated for both the center idler roll and for the side idler roll. It also presents the results of calculations of belt rolling resistances for the analyzed distributions. In addition, it presents the results of calculations with allowance for load distribution along the generating line of the idler.
Go to article

Abstract

DC resistivity soundings and geomorphological surveys have been carried out in the marginal zones and adjacent outwash plains of two glaciers in central Spitsbergen, Norwegian Arctic: Ebbabreen and Hörbyebreen. The study has revealed complex relationships between landforms, buried glacier ice and permafrost. From this work it is possible to distinguish between moraine ridges which are ice-cored and those which are not. The latter occur in areas which have possibly been affected by glacier surge. The active layer thickness was found to be 0.4 to 2.5 m for diamicton deposits (moraines) and 0.3 to 1.6 m in outwash glacifluvial sediments. The sediment infill thickness in valleys was determined to be as much as 20 m, thereby demonstrating that sandurs have important role in sediment storage in a glacial system. Typical resistivity values for sediment types in both the active layer and in permafrost were also determined.
Go to article

Abstract

The main objective of this study was to assess the environmental impact of the subsurface geological structure in Nam Son landfill by hydrogeophysical method. The Electrical Resistivity Tomography (ERT), Self- -Potential (SP) and Very Low Frequency (VLF) method was used for geological structure investigation. Three profiles (total 900 m long) of two-dimensional ERT, VLF density sections and 180 SP data points scattered within the study area near the disposal site were implemented. Surface water and groundwater samples were collected from 10 sites in the area for hydrochemical analysis. Interpretations of geophysical data show a low resistivity zone (<15 Ω m), which appears to be a fully saturated zone with leachate from an open dumpsite. There is a good correlation between the geophysical investigations and the results of hydrochemical analysis.
Go to article

Abstract

In this paper an attempt to determine the relationship between the electrical resistivity and the tensile strength and hardness of cast iron of carbon equivalent in the range from 3.93% to 4.48%. Tests were performed on the gray cast iron for 12 different melts with different chemical composition. From one melt poured 6 samples. Based on the study of mechanical and electro-resistive determined variation characteristics of tensile strength, hardness and resistivity as a function of the carbon equivalent. Then, regression equations were developed as power functions describing the relationship between the resistivity of castings and their tensile strength and hardness. It was found a high level of regression equations to measuring points, particularly with regard to the relationship Rm=f(ρ). The obtained preliminary results indicate the possibility of application of the method of the resistance to rapid diagnostic casts on the production line, when we are dealing with repeatable production, in this case non variable geometry of the product for which it has been determinated before a regression equation.
Go to article

Abstract

The paper describes the influence of graphite shape, size and amount to electrical properties of different cast irons. Experiments of electrical resistivity measurements were conducted during solidification of four different melts in different time intervals from melt treatment by inoculation and nodularization. Metallographic analyses were made in order to determine the shape, size, distribution and amount of graphite and correlate results with electrical resistivity measurements. It was found out that nodular graphite is giving the lowest electrical resistivity and is decreased during solidification. Electrical resistivity of lamellar cast iron is increased during solidification since lamellas interrupt metal matrix severely There is no significant difference in resistivity of vermicular cast iron from nodular cast iron. Smaller size of graphite and lower amount of graphite and higher amount of metal matrix also decrease resistivity.
Go to article

Abstract

The main scientific goal of this work is the presentation of the role of selected geophysical methods (Ground-Penetrating Radar GPR and Electrical Resistivity Tomography ERT) to identify water escape zones from retention reservoirs. The paper proposes a methodology of geophysical investigations for the identification of water escape zones from a retention fresh water lake (low mineralised water). The study was performed in a lake reservoir in Upper Silesia. Since a number of years the administrators of the lake have observed a decreasing water level, a phenomenon that is not related to the exploitation of the object. The analysed retention lake has a maximal depth between 6 and 10 m, depending on the season. It is located on Triassic carbonate rocks of the Muschelkalk facies. Geophysical surveys included measurements on the water surface using ground penetration radar (GPR) and electrical resistivity tomography (ERT) methods. The measurements were performed from watercrafts made of non-metal materials. The prospection reached a depth of about 1 to 5 m below the reservoir bottom. Due to large difficulties of conducting investigations in the lake, a fragment with an area of about 5,300 m 2, where service activities and sealing works were already commenced, was selected for the geophysical survey. The scope of this work was: (1) field geophysical research (Ground-Penetrating Radar GPR and Electrical Resistivity Tomography ERT with geodesic service), (2) processing of the obtained geophysical research results, (3) modelling of GPR and ERT anomalies on a fractured water reservoir bottom, and (4) interpretation of the obtained results based on the modelled geophysical anomalies. The geophysical surveys allowed for distinguishing a zone with anomalous physical parameters in the area of the analysed part of the retention lake. ERT surveys have shown that the water escape zone from the reservoir was characterised by significantly decreased electrical resistivities. Diffraction hyperboles and a zone of wave attenuation were observed on the GPR images in the lake bottom within the water escape zone indicating cracks in the bottom of the water reservoir. The proposed methodology of geophysical surveys seems effective in solving untypical issues such as measurements on the water surface.
Go to article

Abstract

The paper presents the initial results of investigation concerning the abrasion resistance of cast iron with nodular, vermicular, or flake graphite. The nodular and vermicular cast iron specimens were cut out of test coupons of the IIb type with the wall thickness equal to 25 mm, while the specimens made of grey cast iron containing flake graphite were cut out either of special casts with 20 mm thick walls or of the original brake disk. The abrasion tests were carried out by means of the T-01M tribological unit working in the pin-on-disk configuration. The counterface specimens (i.e. the disks) were made of the JT6500 brand name friction material. Each specimen was abraded over a distance of 4000 m. The mass losses, both of the specimens and of the counterface disks, were determined by weighting. It was found that the least wear among the examined materials was exhibited by the nodular cast iron. In turn, the smallest abrasion resistance was found in vermicular cast iron and in cast iron containing flake graphite coming from the brake disk. However, while the three types of specimens (those taken from the nodular cast iron and from grey cast iron coming either from the special casts or from the brake disk) have almost purely pearlitic matrix (P95/Fe05), the vermicular cast iron matrix was composed of pearlite and ferrite occurring in the amounts of about 50% each (P50/Fe50). Additionally, it was found that the highest temperature at the cast iron/counterface disk contact point was reached during the tests held for the nodular cast iron, while the lowest one occurred for the case of specially cast grey iron.
Go to article

Abstract

Between 2004 and 2017, multiple studies on the herbicide resistance of weeds were conducted by the Institute of Plant Protection – National Research Institute in Poland. Weed seeds, collected from fields located in various regions of Poland where herbicide use was ineffective, were used in studies conducted under greenhouse conditions. A total of 261 loose silky bent (Apera spica-venti L.) samples were found to be herbicide resistant, which translates to 52.4% of the fields under study. Nearly 50% of the analyzed samples exhibited resistance to sulfonylurea herbicides. Resistance to acetyl CoA carboxylase (ACCase) inhibitors was found in 18 fields, whereas resistance to photosystem II (PSII) inhibitors (isoproturon) was found in 12 fields. Herbicide resistance of blackgrass (Alopecurus myosuroides Huds.) occurred in 26 of the fields under study. In addition, resistance of wild oat (Avena fatua L.) to acetyl CoA carboxylase inhibitors occurred in 10 spring cereal crops. In the case of winter wheat, resistance of cornflower (Centaurea cyanus L.) to tribenuron-methyl occurred in 23 fields. Scentless chamomile (Matricaria inodora L.) and field poppy (Papaver rhoeas L.) were resistant to tribenuron-methyl in four and three fields, respectively, of winter wheat. In the case of sugar beet, three biotypes of fat hen (Chenopodium album L.) and two biotypes of redroot amaranth (Amaranthus retroflexus L.) were resistant to metamitron. Horseweed (Conyza canadensis L.), which grows on railway tracks, exhibited resistance to glyphosate. This paper reviews all studies conducted in Poland on weed resistance. Based on the results, maps of weed resistance in Poland were created.
Go to article

Abstract

A revision of the standard approach to characterization of thin-semiconductor-layer Hall samples has been proposed. Our results show that simple checking of I(V) curve linearity at room temperature might be insufficient for correct determination of bias conditions of a sample before measurements of Hall effect. It is caused by the nonlinear behaviour of electrical contact layers, which should be treated together with the tested layer a priori as a metal-semiconductor-metal (MSM) structure. Our approach was examined with a Be-doped p-type InAs epitaxial layer, with four gold contacts. Despite using full high-quality photolithography a significant asymmetry in maximum differential resistance (Rd) values and positions relative to zero voltage (or current) value was observed for different contacts. This suggests that such characterization should be performed before each high-precision magneto-transport measurement in order to optimize the bias conditions.
Go to article

This page uses 'cookies'. Learn more