Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 9
items per page: 25 50 75
Sort by:

Abstract

This study used ground penetrating radar soundings to examine a tongue-shaped rock glacier (64°04’S 58°25’W) on James Ross Island, Antarctic Peninsula, in January 2005. The rock glacier studied has multiple well-developed transverse ridges and approximately 800 m long from the talus of its head to its frontal slopes and is 300 m wide in the middle. The longitudinal ground penetrating radar profile identified debris bands which dip up-glacier, similar to the thrust structures in the compression zone of a valley glacier. Transverse ground penetrating radar profiles indicated a layered structure which is inclined towards the central part of the rock glacier and which resembles the transverse foliation of a valley glacier. Consequently, the internal structure of the rock glacier is revealed as being similar to the “nested spoons” common in the interior of valley glaciers. We concluded that this rock glacier has been created by the deformation of a glacier ice core and a thick and continuous debris mantle.
Go to article

Abstract

GPR method is perfectly suited for recognizing of sedimentary facies diversity in shallowly occurring sediments if there is a contrast of electrical properties between and/or within each layer. The article deals with the issue of the correlation between GPR surveys results and sedimentological analyses. As a result of this correlation a conceptual model of depositional systems of studied areas was developed. Studies were performed in two areas located in central Poland, where glacial deposits formed in the Middle Polish (Saalian) Glaciation are present. The study was based on 49 sediment samples and 21 GPR profiles. Analyses of lithofacies as well as granulometric and mineralogical composition of deposits of collected samples were carried out, showing the diversity of glacial deposits in both study sites. During GPR measurements shielded antenna with a frequency of 500 MHz was used which allowed high-resolution mapping of the internal structure of deposits and to identify four characteristic radar facies. Correlation of GPR profiles with point, one-dimensional sedimentological studies allowed the unambiguous interpretation of the GPR image and draw conclusions about the formation environment of individual units. Geophysical and sedimentological data obtained during study provide a new and detailed insight into selected glacial deposits in central Poland.
Go to article

Abstract

The main scientific goal of this work is the presentation of the role of selected geophysical methods (Ground-Penetrating Radar GPR and Electrical Resistivity Tomography ERT) to identify water escape zones from retention reservoirs. The paper proposes a methodology of geophysical investigations for the identification of water escape zones from a retention fresh water lake (low mineralised water). The study was performed in a lake reservoir in Upper Silesia. Since a number of years the administrators of the lake have observed a decreasing water level, a phenomenon that is not related to the exploitation of the object. The analysed retention lake has a maximal depth between 6 and 10 m, depending on the season. It is located on Triassic carbonate rocks of the Muschelkalk facies. Geophysical surveys included measurements on the water surface using ground penetration radar (GPR) and electrical resistivity tomography (ERT) methods. The measurements were performed from watercrafts made of non-metal materials. The prospection reached a depth of about 1 to 5 m below the reservoir bottom. Due to large difficulties of conducting investigations in the lake, a fragment with an area of about 5,300 m 2, where service activities and sealing works were already commenced, was selected for the geophysical survey. The scope of this work was: (1) field geophysical research (Ground-Penetrating Radar GPR and Electrical Resistivity Tomography ERT with geodesic service), (2) processing of the obtained geophysical research results, (3) modelling of GPR and ERT anomalies on a fractured water reservoir bottom, and (4) interpretation of the obtained results based on the modelled geophysical anomalies. The geophysical surveys allowed for distinguishing a zone with anomalous physical parameters in the area of the analysed part of the retention lake. ERT surveys have shown that the water escape zone from the reservoir was characterised by significantly decreased electrical resistivities. Diffraction hyperboles and a zone of wave attenuation were observed on the GPR images in the lake bottom within the water escape zone indicating cracks in the bottom of the water reservoir. The proposed methodology of geophysical surveys seems effective in solving untypical issues such as measurements on the water surface.
Go to article

Abstract

Large-scale stone-banked lobes and terraces are distributed over an area of 1 km2 of gentle slope on Rink Plateau in the northern part of James Ross Island, Antarctic Peninsula region. Topographically, there are two main features: relatively high risers up to 5 m high and distinct frontal ridges. In order to understand the processes responsible for these lobes and terraces, the authors have monitored air and ground temperatures and movement of stones on the surface over the period 1995-2005. In February 2005, the subsurface structures were surveyed by ground penetrating radar and drilling. The ground penetrating radar profiles identified the bedrock surface. The surface morphology of the lobes corresponds closely with that of the bedrock. The relatively high risers of these lobes are presumed to be due to a cessation of frontal advance.
Go to article

Abstract

Measurements were made of sediment characteristics, benthic microbial activity and optimum temperature for sulfate reduction at Signy Island, South Orkney Islands, Antarctica . There was little evidence to support any seasonal variation in oxygen penetration of surface sediments. Oxygen penetrated to only 1.5 to 3 mm throughout the year, despite bioturbation from a dense amphipod population. The distribution of acid volatile sulfides increased with depth below 1 cm and above this, surface sediments were lighter in colour and contained fewer sulfides. The rates of sulfate reduction increased during winter under sea-ice cover, and remained high after ice break up. Seasonal water temperature was relatively constant between –1.8 and 0.5°C. Optimum temperature for anaerobic sediment respiration was investigated using different substrates and was found to be in the range 17–27°C, suggesting that sulfate reducing bacteria are psychrotolerant as they were inhibited by low temperatures.
Go to article

Abstract

The aim of the study is to identify the relevant aspects of numerical analysis of impact of projectiles with soft cores into a package composed of thin flexible plies located on the plastic backing. In order to illustrate the problem, normal impact of 7.62 mm TT projectile into an unclamped package comprising 36 plies of Dyneema SB71 supported on the plastic backing was selected. The problem was solved with the use of the finite element method (FEM) with the explicit integration scheme (central difference method) of motion equations in the matrix form. Based on the conducted numerical computations, it was revealed that obtaining the extreme deformations of a projectile soft core and the backing material in Lagrangian description requires employment of adaptive methods. The proposed R-adaptive method performs its role but must be used carefully due to the mass loss which may appear during calculations.
Go to article

Abstract

The main goal of the article is to identify artificially created defects like lack of fusion and incomplete penetration in butt weld joint using non-destructive volumetric methods. These defects are the most serious defects in welds of steel constructions from the safety point of view. For identification, an ultrasonic phased array technique and a conventional X-ray using digital imaging were used. The theoretical part of the article describes the current state of the given issue and provides basic theoretical knowledge about ultrasonic and X-ray welding tests. In the experimental part, the procedure and results of testing butt weld joint are described by both non-destructive methods. The butt weld joint was made from steel S420MC. Each indication obtained by the ultrasonic and x-ray technique is supplemented by the macrostructure of the weld taken from the indication position. The results of the experimental work mentioned in the article point to the possibility and reliability of the identification of melting defects by selected nondestructive methods in terms of their character and orientation.
Go to article

Abstract

This paper presents the impact of microwave penetration depth on the process of heating the moulding sand with sodium silicate. For each material it is affected by: the wavelength in vacuum and the real and imaginary components of the relative complex electrical permittivity εrfor a selected measurement frequency. Since the components are not constant values and they change depending on the electrical parameters of materials and the frequency of the electromagnetic wave, it is indispensable to carry out laboratory measurements to determine them. Moreover, the electrical parameters of materials are also affected by: temperature, packing degree, humidity and conductivity. The measurements of the dielectric properties of moulding sand with sodium silicate was carried out using the perturbation method on a stand of waveguide resonance cavity. The real and imaginary components of the relative complex electrical permittivity was determined for moulding sand at various contents of sodium silicate and at various packing degrees of the samples. On the basis of the results the microwave penetration depth of moulding sand with sodium silicate was established. Relative literature contains no such data that would be essential to predicting an effective process of microwave heating of moulding sand with sodium silicate. Both the packing degree and the amount of sodium silicate in moulding sand turned out to affect the penetration depth, which directly translates into microwave power density distribution in the process of microwave heating of moulding sand with sodium silicate.
Go to article

This page uses 'cookies'. Learn more