It has been shown in the present paper that exploitation of the experimental potential of a photoacoustic technique can provide information on a type of intermolecular interactions in aqueous mixtures containing organic liquids, when the basic parameters of these mixtures, such as density, ρ, specific heat, cp, or thermal conductivity, λ, are unknown. Earlier investigations of concentration dependence of effusivity in different aqueous solutions of organic liquids demonstrated that the photoacoustics method is a sensitive tool to identify hydrophobic properties of such liquids. In our experiment this suggestion was exploited for a solution of methanol which is known to display much weaker hydrophobicity than other alcohols. It was confirmed that the location of extreme deviations from linearity for the thermal effusivity, Δe, agrees well with that of characteristic points for the isentropic compressibility coefficient, κS, and the excess molar volume, V_m^E, as a function of the concentration.
Polish Academy of Sciences, Institute of Chemical Engineering, 44-100 Gliwice, Bałtycka 5, Poland A review concerning main processes of hydrogenation of carbon oxides towards synthesis of methanol, mixture of methanol and higher aliphatic alcohols and one-step synthesis of dimethyl ether as well as methanol steam reforming is given. Low-temperature methanol catalysts and lowtemperature modified methanol catalysts containing copper as primary component and zinc as secondary one are described.
In this article, the contribution of renewable energy sources (RES) to the worldwide electricity production was analyzed. The scale of development and the importance of RES in the global economy as well as the issues and challenges related to variability of these sources were studied. In addition, the chemical conversion of excess energy to renewable methanol has been presented. The European Union regulations and targets for the years 2020 and 2030 concerning greenhouse gases reduction were taken into consideration. These EU restrictions exact the further development of renewable energy sources, in particular, the improvement of their efficiency which is closely related to economics. Moreover, as a part of this work, energy storage were described as one of the ways to increase the competitiveness of renewable energy sources with respect to conventional energy. A method for the conversion of carbon dioxide separated from high-carbon industries with hydrogen obtained by the over-production of green energy were described. The use of methanol in the chemical industry and global market have been reviewed and thus an increasing demand was observed. Additionally, the application of renewable methanol as fuels, in pure form and after a conversion of methanol to dimethyl ether and fatty acid methyl esters has been discussed. Hence, the necessity of modifying car engines in order to use pure methanol and its combination with petrol also was analyzed.
The results of activity studies of four catalysts in methanol synthesis have been presented. A standard industrial catalyst TMC-3/1 was compared with two methanol catalysts promoted by the addition of magnesium and one promoted by zirconium. The kinetic analysis of the experimental results shows that the Cu/Zn/Al/Mg/1 catalyst was the least active. Although TMC-3/1 and Cu/Zn/Al/Mg/2 catalysts were characterised by a higher activity, the most active catalyst system was Cu/Zn/Al/Zr. The activity calculated for zirconium doped catalyst under operating conditions was approximately 30% higher that of TMC-3/1catalyst. The experimental data were used to identify the rate equations of two types - one purely empirical power rate equation and the other one - the Vanden Bussche & Froment kinetic model of methanol synthesis. The Cu/ZnO/Al2O3 catalyst modified with zirconium has the highest application potential in methanol synthesis.
The aim of the study was to examine the efficiency of the thermal wave type adsorption refrigerating equipment working on a pair of activated carbon and methanol. Adsorption units can work in trigeneration systems and in applications driven by waste heat. They can be built also as a part of hybrid sorption-compressor systems, and they are very popular in solar refrigeration systems and energy storage units. The device examined in this study operates in a special mode called thermal wave. This mode allows to achieve higher efficiency rates than the normal mode of operation, as a significant contributor to transport heat from one to the other adsorber. To carry out the experiment a test bench was built, consisting of two cylindrical adsorbers filled with activated carbon, condenser, evaporator, oil heater and two oil coolers. Thermal oil circulation was responsible for providing and receiving heat from adsorbers. In order to perform the correct action a special control algorithm device was developed and implemented to keep the temperature in the evaporator at a preset level. The experimental results show the operating parameters changes in both adsorbers. Obtained COP (coefficient of performance) for the cycle was 0.13.