Concentration of Zn, Cu, Cd, Pb and Co have been determined in Antarctic water (South Shetland Islands) and in krill exoskeletons with the help of atomic absorption spectrophotometry. Concentrations of these metals both in sea-water and in krill exoskeleton are in order Zn > Cu > Cd > Ni > Pb > Co. Comparing concentrations of these metals in sea-water to their concentrations in krill exoskeleton, the factors have been calculated giving a list of metals in the order of krill chitin ability, which is Ni > Cu > Zn > Cd > Pb > Co accumulation. The highest accumulation factors for Ni and Cu point out to the special role played by these metals in krill life.
The contents of copper, manganese, zinc, lead and cadmium have been determined in plants of the Spitsbergen tundra, collected at Calypsostranda, Lyellstranda and Chamberlindalen in 1987. Five species of vascular plants, four species of mosses and fourteen species of lichens have been investigated. Manganese content in all the studied plants falls in the physiological limits of this element. Appreciable concentrations of copper, and zinc exceeding the physiological concentrations of these elements and presence of lead and cadmium have been shown for many plants.
Metal contents in the tundra soils (Gelic Regosols, Gelic Gleysols, Gelic Cambisols) of the maritime lowland of Kaffiöyra, in the western Spitsbergen seashore are presented in this publication. The average heave metal contents in samples collected from the depth layer 0—130 cm are follows: Fe 2.9%, Mn 392 ppm, Zn 75 ppm, Cu 23.4 ppm, Ni 24.1 ppm, Co 7.4 ppm, Pb 12.5 ppm, Cd 0.24 ppm. The surface soil layer 0 to 25 cm is poorer in Ca and Mg than the underlying layer 25 to 130 cm. The heave metal contents like Fe, Mn, Ni and Co, are also somewhat lower in the upper layer. The enrichment indices of Pb and Cd are equal in the surface soil layer 1.16 and 1.23 respectively. Correlation coefficients between each studied element and organic carbon, and, on the other hand, soil separates < 20 μm and < 2 μm are very low.
The results of studies on the air pollution and on the natural sedimentation from the atmosphere in the South Shetlands are (Admiralty Bay) are presented. The amount of dust in the air varied from 0.11 to 10.90 μg x m-3 (the mean being 3.70 μg x m-3). The total amount of substances transported from the atmosphere in the Admiralty Bay region was estimated at 12.7t x km-2 per year, whereas the precipitation transports some 2.5 t x km-2 per year in this region. Preliminary data on the contents of Cu. Cd. Co. Ni. Pb and Zn in the samples of surface waters, snow and rain in the region of the Admiralty Bay are presented and compared with the results of the authors.
Distribution of the following elements: Na, K, Ca and Mg, and heavy metals: Fe, Mn, Zn, Cu, Ni, Co, Pb and Cd was analysed in the Gelic Cambisols profile from Kaffiöyra, Spitsbergen. The leaching of Ca, Fe, Mn, Co and Cu, and in a less degree Mg and Ni downward the profiles occurs in the studied soil due to pedogenic processes. The surface soil horizon is strongly enriched in Na and K of marine origin and Pb and Cd from anthropogenic pollution of the distant atmospheric transports.
This paper presents the results of experiments on metallization of plastic elements produced using 3D printing technology from the light-hardened resins. The obtained coatings were bimetallic (Cu/Ni). The first step of metallization was the electroless deposition of copper. The second one was electrodeposition of nickel on the previously prepared copper substrate. The parameters of 3D prints preparation and metallization processes were deeply investigated. The etching of plastics substrates and duration of electroless metallization of 3D prints by copper were analyzed. In the next step the influence of nickel electrodeposition time was investigated. The coating were analyzed by XRD method and morphology of surface was analyzed by scanning electron microscopy (SEM). The thickness of coatings was calculated based on mass differences and measured by using optical microscopy method. The optimal parameters for both processes were specified.
The analysis of leaching behavior of harmful substances, such as arsenic, is one of the parameters of risk assessment resulting from the storage or economic use of coal waste. The leachability depends both on the environmental conditions of the storage area as well as on the properties of the waste material itself. There are a number of leaching tests that allow to model specific conditions or measure the specific properties of the leaching process. The conducted research aimed at comparing two methods with different application assumptions. The study of arsenic leaching from waste from the hard coal enrichment process was carried out in accordance with the Polish PN-EN 12457 standard and the US TCLP procedure. The leaching results obtained with both methods did not exceed the limit values of this parameter, defined in the Polish law. Both methods were also characterized by the good repeatability of the results. The use of an acetic acid solution (TCLP method) resulted in three times higher arsenic leaching from the examined waste compared to the use of deionized water as a leaching fluid (method PN-EN 12457). Therefore, the use of organic acid tests for mining waste intended for storage with municipal waste should be considered, as the results of the basic test based on clean water leaching may be inadequate to the actual leaching of arsenic under such environmental conditions.