Search results

Filters

  • Journals
  • Keywords
  • Date

Search results

Number of results: 23
items per page: 25 50 75
Sort by:

Abstract

Many performing artists in the interwar period in Poland assumed stage names, which were considered a tool of promoting one’s image, but also served other functions, such as the concealment of identity. Over two hundred such pseudonyms — together with the respective artists’ birth names — have been collected and analysed in the article. Approximately in the case of half of them was the original given name retained, and only the surname underwent a change. The comparison of the assumed names with the real ones shows that many names were shortened, and/or made to sound foreign or exotic. Minority surnames — Jewish/German, Russian, Ukrainian — were frequently made to sound Polish, while the Polish ones were foreignised (to make them look English, Italian, French) or vaguely exoticised.
Go to article

Abstract

Studies of noise properties of thick-film conducting lines from Au or PdAg conductive pastes on LTCC or alumina substrates are reported. Experiments have been carried out at the room temperature on samples prepared in the form of meanders by traditional screen-printing or laser-shaping technique. Due to a low resistance of the devices under test (DUTs), low-frequency noise spectra have been measured for the dc-biased samples arranged in a bridge configuration, transformer-coupled to a low-noise amplifier. The detailed analysis of noise sources in the signal path and its transfer function, including the transformer, has been carried out, and a procedure for measurement setup self-calibration has been described. The 1/f noise component originating from resistance fluctuations has been found to be dominant in all DUTs. The analysis of experimental data leads to the conclusion that noise is produced in the bends of meanders rather than in their straight segments. It occurs that noise of Au-based laser-shaped lines is significantly smaller than screen-printed ones. PdAg lines have been found more resistive but simultaneously less noisy than Au-based lines.
Go to article

Abstract

Pośród filmów podejmujących tematykę Zagłady oraz obojętności (a nawet współwiny Polaków) na los Żydów, ważne znaczenie ma Dekalog VIII (1988) Krzysztofa Kieślowskiego. Jego pierwszoplanowymi postaciami są Elżbieta, której jako żydowskiemu dziecku Zofia, obecnie profesor etyki, odmówiła ratunku podczas wojny pod pretekstem zawartego w Dekalogu zakazu kłamstwa. Ich rozmowa po czterech dziesięcioleciach, pozwalająca na poznanie prawdy o motywach postępowania, prowadzi do pojednania opartego na przebaczeniu. Kieślowski w swoim filmie wprowadza również wątek teologiczny, stawiając pytanie o istnienie Boga. Oprócz utworu Kieślowskiego, tematyka pomocy udzielanej Żydom, ale również obojętności, a nawet współodpowiedzialności Polaków wobec Zagłady, obecna jest w licznych polskich filmach fabularnych i dokumentalnych. Wątkiem, który w nich powraca, jest także rola ludzi wierzących, którzy nie zawsze potrafili sprostać wymogom sumienia i wiary.
Go to article

Abstract

Falling film, shell-tube type evaporators are commonly used heat exchangers for the production of fruit juice concentrate. The main problem in the design of the exchanger is a reliable estimation of wall heat transfer coefficients for all effects in real operating conditions. Most literature sources for the overall heat transfer coefficients are based on laboratory measurements, where the tubes are usually short, no fouling exists and the flow rate is carefully adjusted. This paper shows the heat transfer estimated in real industrial operating conditions, compared to literature sources. Paper is based on the author’s own experience in designing and launching several evaporators for juice concentrate production into operation. As a summary, the design heat transfer coefficients are provided with relation to sugar content in juice concentrate.
Go to article

Abstract

The paper presents general information on LTCC materials, manufacturing processes and properties of fired modules. A Multichip Module package has been the main application of Low Temperature Cofired Ceramic (LTCC) technology. Recently, this technology is also used for production of sensors, actuators and microsystems. The research and development on the LTCC sensors and microsystems carried out in the Laboratory of Thick Film Microsystems at Wroclaw University of Technology are presented. LTCC microfluidic system is described in detail. Moreover, a short information is given on other LTCC applications .
Go to article

Abstract

In modern microelectronics progress has been made towards low power ultra large-scale integration (ULSI), and nano-structure devices such as single electron transistors and quantum dots. In this technology application of new materials, which includes high-κ dielectrics for the MOSFET transistors, with extraordinary purity and uniformity is required. Failure analysis and reliability investigations of such films very often requires highresolution local measurements of electrical surface parameters. This kind of experiments can be performed using conductive atomic force microscopy, which provides simultaneous measurement of surface topography and current ?owing through the investigated layer. In order to acquire reliable data, there was designed a precise measurement and control system, which included a low-noise current-to-voltage converter of picoampere resolution, a scanning stage with control electronics and a data acquisition system. In the paper we describe the architecture of the designed and applied experimental set-up. We also present results of simultaneous measurements of topography and current on gold and highly oriented pyrolytic graphite (HOPG).
Go to article

Abstract

Nowadays, there are growing demands on the accuracy of production. Most of this is reflected in precise manufacturing, such as the investment casting process. Foundries are looking for causes of defects in some cases for a very long time, and it may happen that the source of defects is completely different from what was originally assumed. During the casting process there exist potential causes of defects as oxygen inclusions. This paper represents a summary of the beginnings of a wider research that will address the problems of gating systems in investment casting technology. In general, the influence of the melt flow is underestimated and the aim of the whole scientific research is to demonstrate the significant influence of laminar or turbulent flow on the resulting casting quality. Specifically, the paper deals with the analysis of the most frequent types of defects found in castings made of expensive types of materials casted in an open atmosphere and demonstration of connection with the design of gating systems in the future.
Go to article

Abstract

Polski film fabularny w latach 60. XX wieku był nie tylko medium przynoszącym rozrywkę czy też naukę, przyczynił się także do kształtowania gustów Polaków w zakresie architektury wnętrz. Architektura wnętrz w omawianym okresie stała się ponownie polem do szeroko zakrojonych eksperymentów twórczych noszących znamiona nowoczesności. Obraz filmowy tego czasu w wielu przypadkach stał się zapisem historii polskiego wnętrzarstwa. Z perspektywy czasu, który minął możemy traktować kadry filmu jako obraz historyczny, dzięki któremu istnieje możliwość zobaczenia dzieł w ich naturalnym środowisku.
Go to article

Abstract

Graphene is a very promising material for potential applications in many fields. Since manufacturing technologies of graphene are still at the developing stage, low-frequency noise measurements as a tool for evaluating their quality is proposed. In this work, noise properties of polymer thick-film resistors with graphene nano-platelets as a functional phase are reported. The measurements were carried out in room temperature. 1/f noise caused by resistance fluctuations has been found to be the main component in the specimens. The parameter values describing noise intensity of the polymer thick-film specimens have been calculated and compared with the values obtained for other thick-film resistors and layers used in microelectronics. The studied polymer thick-film specimens exhibit rather poor noise properties, especially for the layers with a low content of the functional phase.
Go to article

Abstract

Hydrogen (H2) and liquid petroleum gas (LPG) sensing properties of SnO2 thin films obtained by direct oxidation of chemically deposited SnS films has been studied. The SnS film was prepared by a chemical technique called SILAR (Successive Ionic Layer Adsorption and Reaction). The sensor element comprises of a layer of chemically deposited SnO2 film with an overlayer of palladium (Pd) sensitiser. The Pd sensitiser layer was also formed following a chemical technique. The double layer element so formed shows significantly high sensitivity to H2 and LPG. The temperature variation of sensitivity was studied and the maximum sensitivity of 99.7% was observed at around 200°C for 1 vol% H2 in air. The response time to target gas was about 10 seconds and the sensor element was found to recover to its original resistance reasonably fast. The maximum sensitivity of 98% for 1.6 vol% LPG was observed at around 325°C. The sensor response and recovery was reasonably fast (less than one minute) at this temperature.
Go to article

Abstract

Recently a new technology of piezoelectric transducers based on PZT thick film has been developed as a response to a call for devices working at higher frequencies suitable for production in large numbers at low cost. Eight PZT thick film based focused transducers with resonant frequency close to 40 MHz were fabricated and experimentally investigated. The PZT thick films were deposited on acoustically engineered ceramic substrates by pad printing. Considering high frequency and non-linear propagation it has been decided to evaluate the axial pressure field emitted (and reflected by thick metal plate) by each of concave transducer differing in radius of curvature - 11 mm, 12 mm, 15 mm, 16 mm. All transducers were activated using AVTEC AVG-3A-PS transmitter and Ritec diplexer connected directly to Agilent 54641D oscilloscope. As anticipated, in all cases the focal distance was up to 10% closer to the transducer face than the one related to the curvature radius. Axial pressure distributions were also compared to the calculated ones (with the experimentally determined boundary conditions) using the angular spectrum method including nonlinear propagation in water. The computed results are in a very good agreement with the experimental ones. The transducers were excited with Golay coded sequences at 35-40 MHz. Introducing the coded excitation allowed replacing the short-burst transmission at 20 MHz with the same peak amplitude pressure, but with almost double center frequency, resulting in considerably better axial resolution. The thick films exhibited at least 30% bandwidth broadening comparing to the standard PZ 27 transducer, resulting in an increase in matching filtering output by a factor of 1.4-1.5 and finally resulting in a SNR gain of the same order.
Go to article

Abstract

In this study, agar-based nanocomposite films containing ultra-porous silica aerogel particles were fabricated by gel casting using an aqueous agar/silica aerogel slurry. The silica aerogel particles did not show significant agglomeration and were homogeneously distributed in the agar matrix. Transmission electron microscopy observations demonstrated that the silica aerogel particles had a mesoporous microstructure and their pores were not incorporated into the agar polymer molecules. The thermal conductivities of the agar and agar/5 wt.% silica aerogel nanocomposite films were 0.36 and 0.20 W·m–1·K–1, respectively. The transmittance of the agar films did not decrease upon the addition of silica aerogel particles into them. This can be attributed to the anti-reflection effect of silica aerogel particles.
Go to article

Abstract

Methane (CH4) sensitivity of zinc oxide (ZnO) thin film has been studied in the present work. The sensor element comprises of a chemically fabricated ZnO semiconducting layer and a layer of palladium (Pd) as catalyst. The catalyst layer was formed on the surface of semiconducting ZnO following a wet chemical process from palladium chloride (PdCl2) solution. Fundamental features of a sensor element e.g. sensitivity, response time and recovery process has been studied. The effect of operating temperature on performance of the sensor material has been investigated and a choice of optimum temperature was made at around 200oC. The sensor element exhibited reasonable sensitivity of about 86% at this temperature in presence of 1 vol% methane (CH4) in air.
Go to article

Abstract

Measurement of low-frequency noise properties of modern electronic components is a very demanding challenge due to the low magnitude of a noise signal and the limit of a dissipated power. In such a case, an ac technique with a lock-in amplifier or the use of a low-noise transformer as the first stage in the signal path are common approaches. A software dual-phase virtual lock-in (VLI) technique has been developed and tested in low-frequency noise studies of electronic components. VLI means that phase-sensitive detection is processed by a software layer rather than by an expensive hardware lock-in amplifier. The VLI method has been tested in exploration of noise in polymer thick-film resistors. Analysis of the obtained noise spectra of voltage fluctuations confirmed that the 1/f noise caused by resistance fluctuations is the dominant one. The calculated value of the parameter describing the noise intensity of a resistive material, C = 1·10−21 m3, is consistent with that obtained with the use of a dc method. On the other hand, it has been observed that the spectra of (excitation independent) resistance noise contain a 1/f component whose intensity depends on the excitation frequency. The phenomenon has been explained by means of noise suppression by impedances of the measurement circuit, giving an excellent agreement with the experimental data.
Go to article

Abstract

Studies of electrical properties, including noise properties, of thick-film resistors prepared from various resistive and conductive materials on LTCC substrates have been described. Experiments have been carried out in the temperature range from 300 K up to 650 K using two methods, i.e. measuring (i) spectra of voltage fluctuations observed on the studied samples and (ii) the current noise index by a standard meter, both at constant temperature and during a temperature sweep with a slow rate. The 1/f noise component caused by resistance fluctuations occurred to be dominant in the entire range of temperature. The dependence of the noise intensity on temperature revealed that a temperature change from 300 K to 650 K causes a rise in magnitude of the noise intensity approximately one order of magnitude. Using the experimental data, the parameters describing noise properties of the used materials have been calculated and compared to the properties of other previously studied thick-film materials.
Go to article

Abstract

Semiconductive - resistive sensors of toxic and explosive gases were fabricated from nanograins of SnO2 using thick-.lm technology. Sensitivity, selectivityand stabilityof sensors working in di.erent temperature depend on the way the tin dioxide and additives were prepared. A construction also plays an important role. The paper presents an attitude towards the evaluation of transport of electrical charges in semiconductive grain layer of SnO2, when dangerous gases appear in the surrounding atmosphere.
Go to article

Abstract

It is known that external diffusional resistances are significant in immobilized enzyme packed-bed reactors, especially at large scales. Thus, the external mass transfer effects were analyzed for hydrogen peroxide decomposition by immobilized Terminox Ultra catalase in a packed-bed bioreactor. For this purpose the apparent reaction rate constants, kP, were determined by conducting experimental works at different superficial velocities, U, and temperatures. To develop an external mass transfer model the correlation between the Colburn factor, JD, and the Reynolds number, Re, of the type JD = K Re(n-1) was assessed and related to the mass transfer coefficient, kmL. The values of K and n were calculated from the dependence (am kp-1 - kR-1) vs. Re-1 making use of the intrinsic reaction rate constants, kR, determined before. Based on statistical analysis it was found that the mass transfer correlation JD = 0.972 Re-0.368 predicts experimental data accurately. The proposed model would be useful for the design and optimization of industrial-scale reactors.
Go to article

Abstract

LTCC-based pressure sensors are promising candidates for wet-wet applications in which the effect of the surrounding media on the sensor's characteristics is of key importance. The effect of humidity on the sensor's stability can be a problem, particularly in the case of capacitive sensors. A differential mode of operation can be a good solution, but manufacturing the appropriate sensing capacitors remains a major challenge. In the case of piezoresistive sensors the influence of humidity is less critical, but it still should be considered as an important parameter when designing sensors for low-pressure ranges. In this paper we discuss the stability of the sensors' offset characteristics, which was inspected closely using experimental and numerical analyses.
Go to article

Abstract

GZO/IZO semiconductor thin films were prepared on the ITO substrate via sol-gel spin coating method for using in the dyesensitized solar cells (DSSCs). For this purpose, GZO and IZO thin films were optimized by the percentage of doping gallium and indium in zinc oxide and were studied their electrical, optical and structural properties. After that, the layers with the best performance were selected for use in the DSSCs. The concentration of all solutions for spin coating processes was 0.1 M and zinc oxide has been doped with gallium and indium, with different doping percentages (0, 0.5, 1, 2 and 4 volume percentage). So, by studying the properties of the fabricated thin films, it was found the films with 0.5%GZO and 0.5%IZO have the best performance and hence, the optimized dual-layer (0.5% GZO/0.5% IZO (GIZO)) were prepared and studied their electrical and optical properties. The synthesized optimized dual-layer film was successfully used as the working electrode for dye-sensitized solar cells. The sample with 0.5%IZO shows the 9.1 mA/cm2 short-circuit current density, 0.52 V open circuit voltage, 63% fill factor and 2.98% efficiency.
Go to article

Abstract

Among the various thin film coating techniques, atomic layer deposition (ALD) has features of good controllability of the thickness, excellent step-coverage in 3-dimensional object even in the sub-nm thickness range at the relatively low deposition temperature. In this study, SnO2 thin films were grown by ALD in the variation of substrate temperatures from 150 to 250°C. Even such a low temperature may influence on the growth kinetics of the ALD reaction and thus the physical characteristics of thin films, such as crystallinity, film density and optical band gap, etc. We observed the decrease of the growth rate with increasing substrate temperature, at the same time, the density of the film was decreased with increasing temperature. Steric hindrance effect of the precursor molecule was attributed to the inverse relationship of the growth temperature and growth rate as well as the film density. Optical indirect band gap energy (~3.6 eV) of the ALD-grown amorphous SnO2 films grown at 150°C was similar with that of the literature value, while slightly lower band gap energy (~3.4 eV) was acquired at the films grown at higher temperature.
Go to article

Abstract

The safe and reliable operation of pressurized water reactors (PWRs) depends on the integrity of structural material. In particular, the failure of steam generator (SG) tubes on the secondary side is one of the major concerns of operating nuclear power plants. To establish remediation techniques and manage damage, it is necessary to articulate the mechanism through which various impurities affect the SG tubes. This research aims to understand the effect of impurities (e.g., S, Pb, and Cl) on the stress corrosion cracking of Alloy 600 and 690.
Go to article

Abstract

This paper presents the concept and modern technological approach to the fabrication of discrete, integrated and integral micropassives. The role of these components in modern electronic circuits is discussed too. The material, technological and constructional solutions and their relation with electrical and stability properties are analyzed in details for linear and nonlinear microresistors made and characterized at the Faculty of Microsystem Technology, Wrocław University of Technology.
Go to article

This page uses 'cookies'. Learn more