This paper presents the study of the impact of vibration induced by the movement of the railway rolling stock on the Forum Gdańsk structure. This object is currently under construction and is located over the railway tracks in the vicinity of the Gdańsk Główny and Gdańsk Śródmieście railway stations. The analysis covers the influence of vibrations on the structure itself and on the people within. The in situ measurements on existing parts of the structure allow us to determine environmental excitations used for validation and verification of the derived FEM model. The numerical calculations made the estimates of the vibration amplitudes propagating throughout the whole structure possible.
In order to identify the modal parameters of civil structures it is vital to distinguish the defective data from that of appropriate and accurate data. The defects in data may be due to various reasons like defects in the data collection, malfunctioning of sensors, etc. For this purpose Exploratory Data Analysis (EDA) was engaged toenvisage the distribution of sensor’s data and to detect the malfunctioning with in the sensors. Then outlier analysis was performed to remove those data points which may disrupt the accurate data analysis. Then Data Driven Stochastic Sub-space Identification (DATA-SSI) was engaged to perform the modal parameter identification. In the end to validate the accuracy of the proposed method stabilization diagrams were plotted. Sutong Bridge, one of the largest span cable stayed bridge was used as a case study and the suggested technique was employed. The results obtained after employing the above mentioned techniques are very valuable, accurate and effective.
This paper presents new procedure modeling based on finite element method analysis of wood-framed timber structures. The fasteners linking boards of sheathing with the timber frame both modeled applying shell finite element, with individual material parameters, remain the main objective of this manuscript. Material parameters are obtained from experimental tests and numerical identification. The main objective of the paper is the elaboration of the numerical model with high precision of mapping, and, at the same time, diminishing the number of the unknown simplifying the process of the modeling of timber structures. The new presented method leads to a simplification of analysis of multistory wood-framed multifamily building structures.
The influence that general contractors and subcontractors have on the operation of a company is immense. Keeping this in mind, the authors have decided to develop and algorithm based on the analysis of partnering relations between construction companies that would select the best possible construction company for the purposes of cooperation. This algorithm, developed for a given construction company, is meant to support its decision-making system in the field of the selection of another construction company to cooperate with. The author has made references to earlier research, in which she had used the ELECTRE III method, and in which she bad analysed the possibility of applying the BIPOLAR method in order to solve the problem of the selection of a construction company to develop partnering relations with. The author provided an example of the calculations performed for a selection of construction companies.
Choral singers are among intensive voice users whose excessive vocal effort puts them at risk of developing voice disorders. The aim of the work was to assess voice quality for choral singers in the choir at the Polish-Japanese Academy of Information Technology. This evaluation was carried out using the acoustic parameters from the COVAREP (A Collaborative Voice Analysis Repository For Speech Technologies) repository. A prototype of a mobile application was also prepared to allow the calculation of these parameters. The study group comprised 6 male and 19 female choir singers. The control group consisted of healthy non-singing individuals, 50 men and 39 women. Auditory perceptual assessment (using the RBH scale) as well as acoustic analysis were used to test the voice quality of all the participants. The voice quality of the female choir singers proved to be normal in comparison with the control group. The male choir singers were found to have tense voice in comparison with the controls. The parameters which proved most effective for voice evaluation were Peak Slope and Normalized Amplitude Quotient.
Senecavirus A (SVA) the only member of the Senecavirus genus within the Picornaviridae family, is an emerging pathogen causing swine idiopathic vesicular disease and epidemic transient neonatal losses. Here, SVA strain (CH-HNKZ-2017) was isolated from a swine farm exhibiting vesicular disease in Henan Province of Central China. A phylogenetic analysis based on complete genome sequence indicated that CH-HNKZ-2017 was closely related to US-15-40381IA, indica- ting that a new SVA isolate had emerged in China.
Exploitation of hard coal seams by roadway system is applied by two coal mines in southern Poland in Upper Silesian Basin. It is a secondary mining exploitation carries out in safety pillars of urban areas and shafts within mining areas of closed coal mines. Roadway system is the excavation process of gateways which are made in parallel order leaving coal pillars between them. An optimal width of coal pillar makes roadway stable and reduces subsidence of terrain surface. The article presents results of subsidence simulation caused by partial extraction using empirical and numerical methods on the example of one exploitation field of “Siltech” coal mine. The asymptotic state of subsidence was considered after mining ceased in the study area. In order to simulate of subsidence, numerical model of rock mass and model of Knothe-Budryk theory were calibrated. Simulation of vertical displacements in numerical method was carried out using RS3 program by Rocscience based on finite element method. The assumption was made that model of rock mass is transversely isotropic medium, in which panels were designed according to order of extraction of coal seams. The results of empirical and numerical methods were compared with measured values of subsidence at benchmarks along drawn lines (subsidence profiles).
The term Pakoszówka-Bessów type pottery is used to describe a specific kind of wheelmade pottery with easily abradable surfaces mostly dated to the 3rd century AD. Site 3 in Bessów, Bochnia Commune, Lesser Poland, is located in the dense Przeworsk culture settlement micro-region occupying the right bank of the lower reaches of the Raba River. The most characteristic feature of locally produced artefacts from Bessów, and to a lesser extent from other sites in the region, is the presence of enormous amounts of this pottery. The aim of laboratory analyses carried out on Pakoszówka-Bessów type pottery from Bessów was to verify the hypothesis that abradability of sherd surfaces is attributable to the alteration effect.
The standard PN-EN_1993-1-5:_2008 (Eurocode 3) compared with the standard (PN-B-03200:_1990) used previously in Poland, introduces extended rules referring to the computations of the bearing capacity of the plated structural elements including the shear lag effect. The stress distribution in the width flanges is variable. Therefore in the case of the beam with the shear lag effect cannot be calculated by the classic beam theory. In this article a comparison of the results of the calculations of forces distribution, stresses and displacement according to the rule presented in PN-EN_1993 and results of the numerical computations for_3D model (using finite element method) is presented. The elastic shear lag effects, the elastic shear lag effects including effects of the plate buckling and the elastic-plastic shear lag effects including the local instabilities were analysed. The calculations were performed for beams with a small and a large span and an influence of stiffeners was analysed.
For the construction company, tendering is the most popular way of acquiring contracts. The decision to participate in the tender needs to be made carefully, as it affects the condition of the company and is an important aspect in its quest for success. The bid/no bid decision making is a complex process involving a number of factors. The research carried out so far has mainly concerned the identification of the various kinds of influences on contractors’ bidding decisions. The researchers, on the basis of contractors’ opinions, created rank lists in an attempt to categorize the factors. In this paper the author employs factor analysis which belongs to basic methods of multi-dimensional data analysis. The paper’s aim is first to depict an output set of observed variables, that is bid/no bid factors, in terms of a smaller set of latent variables which cannot be directly observed and then to interpret the dependencies between them.
The research paper presents the results of the dynamic analysis of an existing bar dome subjected to wind loads. The calculation model of the structure was constructed using the finite element method. The dome was subjected to the standard wind pressure, assuming that it is operates in a harmonic manner. The numerical analyses were performed with the application of Autodesk Robot and MES3D. The analysis focused on the impact of selected factors such as the frequency of forcing, wind gustiness coefficient and structural damping on the behaviour of structures.
Transportation networks respond differently to applied policies. The Tehran Metropolitan Area has one of the most complex networks with complex users, which has experienced many of these policies change within the past decades. In this study, some of these policies and their effect on air pollution is investigated. The goal is to pinpoint the variables which have the most effect on various transportation models and investigate how new policies should be focused. In order to do so, long-term variations of air pollution monitoring stations were analyzed. Results show that the most significant parameter that may affect air pollution is users' behavior due to the lack of a public transportation network and its level of comfort. The results of this study will be useful in developing new policies and evaluating their long-term consequences in appropriate models.
The preliminary stage of asphalt mixture production involves the drying and dedusting of coarse aggregates. The most common types of coarse aggregates used are limestone and basalt. In the process of drying and dedusting the dryer filter accumulates large quantities of waste in the form of mineral powder. This paper introduces an investigation into limestone powder waste as a potential microfiller of polymer composites. Physical characteristics such as the granulation the of powder collected from the filter - in terms of the season of its collection and the type of input materials used - were analysed. A scanning electron microscope (SEM) was used for the investigation described within this paper. The obtained results were compared against those of other materials which can be used as polymer composites microfillers.
The paper presents an analysis of the influence of elevated temperature on thin-walled purlins restrained by sheeting. In the first part of the study the bearing capacity of purlins cooperating with sheeting is examined in normal and elevated temperature based on European Standards. Next, special attention is paid to creating a numerical FEM model of the restrained purlins in Abaqus program taking into account different materials properties with respect to temperature increase.
This paper presents application of optical microscope for evaluation of microtexture changes of coarse aggregate during simulated polishing in laboratory. Observations of the apparent changes on surfaces of seven different aggregates are presented. Simulation polishing of aggregate was performed in accordance with PN-EN 1097-8:2009. lmages of the aggregate surface were taken with the optical microscope in the reflection mode in particular stages of polishing. Digital images were analyzed. Standard deviation was determined on the basis of the histogram of intensities from digital images of the surfaces of aggregate grains which was assurned as the measure of changes in microtexture during simulated polishing (namely the σh parameter). Statistical analysis has shown that the changes of the σh parameter between the particular stages of polishing confirm certain trends related to the petrographic characteristic of the rocks. Aggregates which included minerals of similar hardness (granodiorite, dolomile, basalt) were more prone to polishing than gabbro and postglacial. Regeneration of the microtexture, the recovery to its original asperity, occurred in the case of quartz sandstone and steelmaking slag.
Probabilistic analysis of a space truss is presented in the paper. Reliability of such a structure is sensitive to geometrical and material imperfections. The objective of this paper is to present a variant of the point estimate method (PEM) to determine mean values and standard deviations of limit loads of engineering structures. The main advantage presented by this method is the small number of sample calculations required to obtain estimators of investigated parameters. Thus the method is straightforward, requiring only preliminaries of probability theory. This approach is illustrated by limit state analysis of a space truss, considering geometric and material imperfections. The calculations were performed for different random models, so the influence of random parameters on the limit load of the truss can be determined. A realistic snow load was imposed.
In individual dogs, despite good quality of raw sperm, some parameters are significantly changed after thawing, which cannot be predicted. We therefore investigated whether motility parameters objectively obtained by CASA, membrane integrity (MI), cell morphology or a combination are suitable to improve the prediction of bad post-thaw quality. For this purpose 250 sperm analysis protocols from 141 healthy stud dogs, all patients introduced for sperm cryopreservation, were evaluated and a Classification and Regression Tree (CART) -analysis performed. The sperm was routinely collected, analysed, and frozen by using a modified Uppsala system. After thawing, data were routinely examined by using CASA, fluorescent microscopy for membrane integrity (MI) and Hancock’s fixation for evaluation of cell morphology. Samples were sorted by post-thaw progressive motility (P) in good (P > / = 50%, n=135) and bad freezers (P<50%, n=115). Among bad freezers, 73.9% showed in addition post-thaw total morphological abberations of >40% and/or MI <50%. Bad freezers were significantly older than good freezers (p<0.05). Progressive motility (P), velocity curvilinear (VCL), mean coefficient (STR), and linear coefficient (LIN) were potential predictors for post-thaw sperm quality since specifity was best (85.8%) and sensitivity (75.4 %) and accuracy (80.4 %) good. For these objectively measured raw sperm parameters, cut-off values were calculated allowing prediction of bad post-thaw results with high accuracy: P = 83.1 % VCL = 161.3 µm/sec, STR = 0.83 %, and LIN = 0.48 %. Raw sperm samples with values below these cut off values will have below average post-thaw quality with a probability of 85.8%. We conclude that VCL, P, STR and LIN are potential predictors of the outcome of sperm cryopreservation, when combined.
In this paper, the applications of the multivariate data analysis and optimization on vibration signals from compressors have been tested on the assembly line to identify nonconforming products. The multivariate analysis has wide applicability in the optimization of weather forecasting, agricultural experiments, or, as in this case study, in quality control. The techniques of discriminant analysis and linear program were used to solve the problem. The acceleration and velocity signals used in this work were measured in twenty-five rotating compressors, of which eleven were classified as good baseline compressors and fourteen with manufacturing defects by the specialists in the final acoustic test of the production line. The results obtained with the discriminant analysis separated the conforming and nonconforming groups with a significance level of 0.01, which validated the proposed methodology.
Canine parvovirus (CPV) causes acute gastroenteritis in domestic dogs, cats, and several wild carnivore species. In this study, the full-length VP2 gene of 36 CPV isolates from dogs and cats infected between 2016 and 2017 in Beijing was sequenced and analyzed. The results showed that, in dogs, the new CPV-2a strain was the predominant variant (n = 18; 50%), followed by the new CPV-2b (n = 6; 16.7%) and CPV-2c (n = 3; 8.3%) strains, whereas, among cats, the predominant strain was still CPV-2 (n = 9; 25%). One new CPV-2a strain, 20170320-BJ-11, and two CPV-2c strains, 20160810-BJ-81 and 20170322-BJ-26, were isolated and used to perform experimental infections. Multiple organs of beagles that died tested PCR positive for CPV, and characteristic histopathological lesions were observed in organs, including the liver, spleen, lungs, kidneys, small intestines, and lymph nodes. Experimental infections showed that the isolates from the epidemic caused high morbidity in beagles, indicating their virulence in animals and suggesting the need to further monitor evolution of CPV in China.
BIM (Building Information Modelling) is a tool and technology closely related to the planning, design, implementation and management of construction investments – both at the level of a building, as well as infrastructure or civil engineering. It combines advanced spatial modeling (using virtual representations of building elements) with management of information at every level, from the modelling of building’s components, through complex interactions between these elements, to the description of building processes and the behavior of users of the building. This is just a part of many possibilities, the full application depends only on the needs and skills of the system user. Construction dependencies are set at the level of the IFC (Industry Foundation Class) universal standard IFC, its syntax allows to describe not only the physical structure of the object, but also their mutual interactions. This is done in a hierarchical way, i.e. from the superior element there are subsequent, lower-level elements and interactions. So how can this tool be used in urban revitalization? The basic problem here is the excess of information related to and contained in the virtual model. In urban planning and design, most of this data is unnecessary. On the other hand, the data contained in the GIS (Geographic Information System) models, despite correlation with external databases, are insufficient. Basic location data, technical conditions of facilities and infrastructure, property dependencies are not enough to obtain a full picture of the urban space. The solution to the problem of linking these systems is CIM (City Information Modeling). It combines the description of an object derived from IFC with database support at the level of GIS systems. Such a broad approach allows for placing enough information in one virtual space for designing, modeling and analyzing urban space. The article is an attempt to demonstrate what conditions must be met by the CIM system, to extend its functionality to issues related to the revitalization of urban areas: whether and how the information contained in the spatial model can be used to determine the rules for the revitalization of space at the urban level?
Successful slogans in Italian political discourse – This paper aims to describe the notion of ‘sloganisation’, with special regard to the fortune and circulation of certain slogans in Italian public discourse. An analysis of their forms, contexts of occurrence (political propaganda, advertising, football supporters) and means of diffusion (street talk, electoral manifestos, traditional and new media) shows an increasing desemantisation of this kind of message. Slogans are routinely used by political parties and are widely quoted, regardless of their ideological content, merely in order to create identification or to increase the polemical attitude of their leader.
Eighty five faecal samples of the Svalbard reindeer inhabiting the coastal terrace of the northern side of Hornsund were collected in July 2005 and analyzed coprologically. The standard flotation method revealed a 97.6% prevalence of infection at an average intensity of 20 eggs in a single subsample. The quantitative, modified McMaster method helped to estimate the mean number of eggs in a gram of faeces (EPG) at 134.7. In the studied samples eggs of nematodes representing two species, i.e. Ostertagia gruehneri (97.6%, on average 20 eggs in a sample) and Marshallagia marshalli (2.3%, single eggs), were identified.
We describe the spatial variability of snow accumulation on three selected glaciers in Spitsbergen (Hansbreen, Werenskioldbreen and Aavatsmarkbreen) in the winter seasons of 1988/89, 1998/99 and 2001/2002 respectively. The distribution of snow cover is determined by the interrelationships between the direction of the glacier axes and the dominant easterly winds. The snow distribution is regular on the glaciers located E-W, but is more complicated on the glaciers located meridionally. The western part of glaciers is more predisposed to the snow accumulation than the eastern. This is due to snowdrift intensity. Statistical relationships between snow accumulation, deviation of accumulation from the mean values and accumulation variability related to topographic parameters such as: altitude, slope inclination, aspect, slope curvature and distance from the edge of the glacier have been determined. The only significant relations occured between snow accumulation and altitude (r = 0.64-0.91).
This article shows acoustic measurements from Svalbard archipelago in the Arctic, located in the Arctic Ocean. The aim of the research was to show the Svalbard soundscape as well as to record and analyse the spatial-temporal dynamics of the acoustic environment, the human impact on the soundscape and to collect baseline data for future comparative research. Svalbard is interesting for many science disciplines because it has an arctic climate and, at the same time, it is relatively easily accessible. Climatologists, geologists, glaciologists, biologists and even anthropologists could find interesting themes to investigate here. Additionally, the soundscape of Spitsbergen is worthy of detailed examination. This paper presents comparative analysis of the soundscape of various spots near Longyearbyen in Management Area 10. The soundscape analysis of selected valleys shows the strong influence of human activity on the soundscape as well as the variability and characteristic features of the natural Arctic soundscape.
The human voice is one of the basic means of communication, thanks to which one also can easily convey the emotional state. This paper presents experiments on emotion recognition in human speech based on the fundamental frequency. AGH Emotional Speech Corpus was used. This database consists of audio samples of seven emotions acted by 12 different speakers (6 female and 6 male). We explored phrases of all the emotions – all together and in various combinations. Fast Fourier Transformation and magnitude spectrum analysis were applied to extract the fundamental tone out of the speech audio samples. After extraction of several statistical features of the fundamental frequency, we studied if they carry information on the emotional state of the speaker applying different AI methods. Analysis of the outcome data was conducted with classifiers: K-Nearest Neighbours with local induction, Random Forest, Bagging, JRip, and Random Subspace Method from algorithms collection for data mining WEKA. The results prove that the fundamental frequency is a prospective choice for further experiments.