Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 3
items per page: 25 50 75
Sort by:

Abstract

The Legnica deposit is one of the most prospective in the context of future lignite mining. Its extraction will be inseparable from the removal of the rocks of the overburden, the volume of which is very large. Due to the raw material properties, some of the rocks can be classified as accompanying minerals. The raw material identification of overburden sediments in the Legnica lignite deposit is insufficient. So far, they haven’t been the subject of detailed and comprehensive research to prove their usefulness. The article was a summary of the knowledge on this subject. The following should be included in the accompanying minerals: Quaternary sands and gravels, tertiary sands and clays (Poznan clays). They are present in two colour variants in the Legnica deposit - and fiery. The mineral composition of greenish-blue clays allows them to be included in illite-kaolinite- smectite varieties, in turn fiery clays as kaolinite-illite-smectite varieties. The tertiary clays are a very useful raw material for the production of building materials. In addition, they are potential mineral sorbents due to the nature of the association of clay minerals (occurrence of montmorillonite). They also show suitability for building waterproofing barriers. Quaternary gravels and sands, developed in the overburden Legnica deposit are differentiated raw materials. Some of them are raw materials for the construction industry. The glacial tills can be used as a component of ceramic mixtures. Tertiary sands can be used as a proppant material. The information on the raw material properties of these sediments will be one of the essential criteria for their treatment as accompanying minerals. Minerals accompanying those developed in the Legnica deposit should be exploited and deposited selectively. The creation of anthropogenic deposits accumulating these minerals will provide the possibility of their use for decades after the termination of operation.
Go to article

Abstract

Residual stress has a great influence on the metal, but it is difficult to measure at small area using a general method. Residual stress calculations using the Vickers indentation can solve this problem. In this paper, a numerical simulation has been made for the residual stress measurement method of metal material deformed by high-speed impact. Then, the stress-strain curve at the high-speed deformation was confirmed through actual experiments, and the residual stresses generated thereafter were calculated by the Vickers indenter method. A Vickers indentation analysis under the same conditions was performed at the position where a residual stress of about 169.39 MPa was generated. Experiments were carried out and high speed impact was applied to the specimen to generate residual stress. The obtained results indicate that it is possible to identify residual stresses in various metals with various shapes through Vickers indentation measurements, and to use them for process and quality control.
Go to article

Abstract

The amount of waste from washing dolomite aggregates increases continuously. Aggregates are washed to remove clayey pollutants.They consist of a large amount of clay minerals and carbonates. Their properties and amount depends on the type of raw material and type of washing technology. Utilization of waste from washing aggregates is common problem and has not been sought out yet. Their usage as the raw material in ceramics might be environmentally friendly way to utilize them. This paper presents technological properties, phase composition and microstructure analysis of materials made of waste sludge from washing dolomite aggregates. Research was divided into three parts: technological properties analysis, phase composition analysis and microstructure analysis. Samples made of waste dolomite sludge were formed in laboratory clay brick vacuum extruder and fired at 900, 1000 and 1100°C. For final materials, apparent density, open porosity, water absorption, compressive strength and durability were examined. Results of technological research suggest the possibility of the application of the waste sludge from washing aggregates in building ceramics technology as bricks materials. Waste sludge from washing dolomite aggregates can be used as the main raw material of building ceramics masses. Without any additional technological operations (e.g. drying or grinding), the material with satisfactory properties was obtained. According to durability results all obtained materials can be used for masonry protected against water penetration and without contact with soil and ground water and also for masonry subjected to passive exposure (F0 – according to the standard EN 771-1).
Go to article

This page uses 'cookies'. Learn more