Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 5
items per page: 25 50 75
Sort by:

Abstract

CFD modelling of momentum and heat transfer using the Large Eddy Simulation (LES) approach has been presented for a Kenics static mixer. The simulations were performed with the commercial code ANSYS Fluent 15 for turbulent flow of three values of Reynolds number, Re = 5 000, 10 000 and 18 000. The numerical modelling began in the RANS model, where standard k−ε turbulence model and wall functions were used. Then the LES iterations started from the initial velocity and temperature fields obtained in RANS. In LES, the Smagorinsky–Lilly model was used for the sub-grid scale fluctuations along with wall functions for prediction of flow and heat transfer in the near-wall region. The performed numerical study in a Kenics static mixer resulted in highly fluctuating fields of both velocity and temperature. Simulation results were presented and analysed in the form of velocity and temperature contours. In addition, the surface-averaged heat transfer coefficient values for the whole insert length were computed and compared with the literature experimental data. Good compliance of the LES simulation results with the experimental correlation was obtained.
Go to article

Abstract

Gas emissions from underground sites to the atmosphere depend on many factors. Pressure drops are considered to be the most important. However, emissions can also be observed during the initial phase of the pressure rise, following a previous drop in pressure. On the other hand, gas emissions may not be detected when the pressure drops, especially when a previous pressure rise has taken place. The aim of the research was to determine the role of variations in baric tendency on airflow rate and its direction. To solve this problem a numerical model was built utilizing the Ansys Fluent software package. Subsequently, three scenarios of baric tendency variations were tested: a) rise – drop, b) drop – drop, c) drop – rise. The results showed inert behavior of gases. Under scenario (c), 1 hour after the change in tendency gases still were flowing out to the atmosphere. Considering scenario (a), it was proved that even during a pressure drop gas emissions do not take place, which can be crucial for further determination of the gas hazard at the surface or for assessment of the rate of gas emissions from a particular gas emitter. Scenario (b) merely gave an overview of the process and was mainly used for validation purposes. It gave a maximal CO2 concentration of 2.18%vol (comparable to measurements) and a CO2 mass flow rate 0.15kg/s. Taking into account greenhouse gas emissions this amounted to 514 kg CO2/h.
Go to article

Abstract

This paper presents a numerical analysis of an agitated fully baffled cylindrical vessel with a down pumping four blade worn or unworn pitched blade impeller (α = 45° and 30°) under a turbulent flow regime. CFD simulations predict the pumping capacity of the system equipped by worn and unworn pitched blade impeller. Experimental data were taken from the authors’ previous work and compared with results of numerical computations. A good agreement with experimental data was obtained. The ensemble-average mean velocity field with worn and unworn impellers was computed. It follows from the simulation results that the wear rate of the impeller blade has a significantly negative effect on the velocity distribution in an agitated liquid. The greater the destruction of the worn blade, the higher is the deformation of the velocity field around the rotating impeller, with a simultaneous decrease in impeller pumping capacity.
Go to article

Abstract

The paper addresses the issues of quantification and understanding of Solid Oxide Fuel Cells (SOFC) based on numerical modelling carried out under four European, EU, research projects from the 7FP within the Fuel Cell and Hydrogen Joint Undertaking, FCH JU, activities. It is a short review of the main projects’ achievements. The goal was to develop numerical analyses at a single cell and stack level. This information was integrated into a system model that was capable of predicting fuel cell phenomena and their effect on the system behaviour. Numerical results were analysed and favourably compared to experimental results obtained from the project partners. At the single SOFC level, a static model of the SOFC cell was developed to calculate output voltage and current density as functions of fuel utilisation, operational pressure and temperature. At the stack level, by improving fuel cell configuration inside the stack and optimising the operation conditions, thermal stresses were decreased and the lifetime of fuel cell systems increased. At the system level, different layouts have been evaluated at the steady-state and by dynamic simulations. Results showed that increasing the operation temperature and pressure improves the overall performance, while changes of the inlet gas compositions improve fuel cell performance.
Go to article

Abstract

In the paper, the authors discuss the construction of a model of an exemplary urban layout. Numerical simulation has been performed by means of a commercial software Fluent using two different turbulence models: the popular k-ε realizable one, and the Reynolds Stress Model (RSM), which is still being developed. The former is a 2-equations model, while the latter – is a RSM model – that consists of 7 equations. The studies have shown that, in this specific case, a more complex model of turbulence is not necessary. The results obtained with this model are not more accurate than the ones obtained using the RKE model. The model, scale 1:400, was tested in a wind tunnel. The pressure measurement near buildings, oil visualization and scour technique were undertaken and described accordingly. Measurements gave the quantitative and qualitative information describing the nature of the flow. Finally, the data were compared with the results of the experiments performed. The pressure coefficients resulting from the experiment were compared with the coefficients obtained from the numerical simulation. At the same time velocity maps and streamlines obtained from the calculations were combined with the results of the oil visualisation and scour technique.
Go to article

This page uses 'cookies'. Learn more