Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 39
items per page: 25 50 75
Sort by:

Abstract

Three-dimensional (3D) finite element analyses (FEA) are performed to simulate the local compression (LC) technique on the clamped single-edge notched tension (SE(T)) specimens. The analysis includes three types of indenters, which are single pair of cylinder indenters (SPCI), double pairs of cylinder indenters (DPCI) and single pair of ring indenters (SPRI). The distribution of the residual stress in the crack opening direction in the uncracked ligament of the specimen is evaluated. The outcome of this study can facilitate the use of LC technique on SE(T) specimens.
Go to article

Abstract

In the current study, twenty lambs, aged 4 months, half male and half female, were classified into four groups, with five in each group. The experimental three groups of lambs were given intravenous (IV), intramuscular (IM) and subcutaneous (SC) administrations of recombinant ovine interferon-τ (roIFN-τ). The fourth group (normal control) of lambs was given normal saline injections in the same way. After administrations, blood samples were collected from the tested animals at different time points post injection, and the serum titers of roIFN-τ were measured using cytopathic effect (CPE) inhibition bioassay. The results of calculating pharmacokinetic (PK) parameters using DAS software showed that the PK characteristics of roIFN-τ through IV injection conformed to the two-compartment open model, whose half-life of distribution phases (T1/2α) was 0.33±0.034 h and the elimination half-life(T1/2β) was 5.01±0.24 h. However, the PK features of IM injection and SC injection of roIFN-τ conformed to the one compartment open model, whose Tmax were 3.11±0.26 h and 4.83±0.43 h, respectively, together with an elimination half life(T1/2β) of 9.11±0.76 h and 7. 43±0.58 h, and an absorption half-life (T1/2k(a)) of 1.13±0.31 h and 1.85±0.40 h, respectively. The bioavailability of roIFN-τ after IM administration reaches 73.57%, which is greater than that of SC administration (53.43%). These results indicate that the drug administration effect can be preferably obtained following a single dose IM administration of the roIFN-τ aqueous preparation. This study will facilitate the clinical application of roIFN-τ as a potential antiviral agent in future work.
Go to article

Abstract

Applying pesticides to crops is one of the causes of water pollution by surface runoff, and chlorpyrifos, trifluralin and chlorothalonil are used respectively as insecticide, herbicide and fungicide for crop plants widely. To explore effects of three pesticides on aquatic organisms, superoxide dismutase (SOD) and glutathione S-transferase (GST) activities were determined after 24 h and 48 h exposure of D. magna with ages of 6–24 h to several low concentrations of chlorpyrifos (0.36, 0.72, 1.43, 2.86, 5.72 μg∙L−1), trifluralin (0.17, 0.33, 0.66, 1.33, 2.65 mg∙L−1) and chlorothalonil (0.09, 0.18, 0.36, 0.72, 1.43 mg∙L−1) respectively. Main reproductive parameters including first pregnancy time, first brood time, the number of first brood and total fecundity after 21 d exposures at the same concentrations of pesticides as described above were also measured. The results showed that the activities of GST increased in lower concentrations and decreased in higher concentrations after 24 h exposure to three pesticides, respectively. The activities of SOD showed the same changes after 48 h exposure. With the time prolonged, the activities of GST decreased while the activities of SOD increased. After 21 d exposure, the first pregnancy time and first brood time were delayed, while the number of the first brood and total fecundity per female decreased with increasing concentrations. These results corroborated that GST activity was more sensitive to those pesticides than SOD activity, and there was a significant relationship between total fecundity and pesticides-dose(r>0.94, n=6), GST activity after 48 h exposure and total fecundity after 21 d exposure (r>0.92, n=6).
Go to article

Abstract

The field of mechanical manufacturing is becoming more and more demanding on machining accuracy. It is essential to monitor and compensate the deformation of structural parts of a heavy-duty machine tool. The deformation of the base of a heavy-duty machine tool is an important factor that affects machining accuracy. The base is statically indeterminate and complex in load. It is difficult to reconstruct deformation by traditional methods. A reconstruction algorithm for determining bending deformation of the base of a heavy-duty machine tool using inverse Finite Element Method (iFEM) is presented. The base is equivalent to a multi-span beam which is divided into beam elements with support points as nodes. The deflection polynomial order of each element is analysed. According to the boundary conditions, the deformation compatibility conditions and the strain data measured by Fiber Bragg Grating (FBG), the deflection polynomial coefficients of a beam element are determined. Using the coordinate transformation, the deflection equation of the base is obtained. Both numerical verification and experiment were carried out. The deflection obtained by the reconstruction algorithm using iFEM and the actual deflection measured by laser displacement sensors were compared. The accuracy of the reconstruction algorithm is verified.
Go to article

Abstract

Taking bacterial virulence factors as targets is a new therapy for treating host bacterial infection. The aim of this study was to investigate the effect of matrine on α-hemolysin production of Staphylococcus aureus (S. aureus) and reducing the damage to bovine mammary epithelial cells (BMECs) induced by S. aureus α-hemolysin. Subinhibitory concentrations of matrine decreased the production of α-hemolysin in none dose-dependent manner and matrine exhibited a protective effect on S. aureus-induced BMECs injury. The results indicated that the structure of matrine may potentially be used as a basic structure for development of drugs aimed at curing and preventing dairy bovine mastitis.
Go to article

Abstract

The objective of this paper is to evaluate the self- healing properties of a commercially-available geosynthetic clay liner (GCL) using flexible-wall permeameter. The GCLs are produced by the same factory, but the contents of bentonite are different. Also the hydraulic conductivities (HC) of GCLs with no defect are different. In this study, specimens were completely saturated under the backpressure of 20 kPa before the test. Permeability tests were performed on GCL specimens with penetrating flaw and also on specimens permeated with distilled water and CaCl2 solutions. The test results were presented and discussed. Experimental results showed that the GCL with penetrating flaw did not exhibit complete self-healing in the case of flaw. After 120 days, the hydraulic conductivity increased by approximately an order of magnitude. In addition, CaCl2 solutions had a significant influence on the hydraulic conductivity. The research findings might be of interest to researchers and engineers who design liners for landfills and other liquid containment facilities
Go to article

Abstract

Pyrolysis is potentially an effective treatment of oily sludge for oil recovery, and the addition of a catalyst is expected to affect its pyrolysis behavior. In the present study, Fe/Al-pillared bentonite with various Fe/Al ratios as pyrolysis catalyst is prepared and characterized by XRD, N2 adsorption, and NH3-TPD. The integration of Al and Fe in the bentonite interlayers to form pillared clay is evidenced by increase in the basal spacing. As a result, a critical ratio of Fe/Al exists in the Fe/Al-pillared bentonite catalytic pyrolysis for oil recovery from the sludge. The oil yield increases with respect to increase in Fe/Al ratio of catalysts, then decreases with further increasing of Fe/Al ratio. The optimum oil yield using 2.0 wt% of Fe/Al 0.5-pillared bentonite as catalyst attains to 52.46% compared to 29.23% without catalyst addition in the present study. In addition, the addition of Fe/Al-pillared bentonite catalyst also improves the quality of pyrolysis-produced oil and promotes the formation of CH4. Fe/Al-pillared bentonite provides acid center in the inner surface, which is beneficial to the cracking reaction of oil molecules in pyrolysis process. The present work implies that Fe/Al-pillared bentonite as addictive holds great potential in industrial pyrolysis of oily sludge.
Go to article

Abstract

In vitro embryogenic callus is a critical factor for genetic transformation of rice, especially for indica varieties. In this study, we investigated the relationship between polyamines, including putrescine (Put), spermidine (Spd) and spermine (Spm), and callus browning, and we studied the effect of exogenous Put on callus regeneration and on the content of endogenous polyamines. In addition, the expression levels of arginine decarboxylase gene (Adcl) and S-adenosylmethionine decarboxylase gene (Samdc) in embryogenic callus were studied by quantitative Real-time PCR analysis. The results showed that the contents of endogenous Put and Spd in the browning callus were significantly lower than those in normal callus. Exogenous Put could effectively improve the growing state of callus of indica rice and enhance the development of embryogenic callus. The content of endogenous polyamines in embryogenic callus, especially Spd and Spm, was increased after addition of exogenous Put. Additionally, exogenous Put also had an obvious impact on the expression levels of Adcl but partial effect on the expression levels of Samdc gene. This study could increase the knowledge of both embryogenic callus induction and polyamine catabolism in callus in indica rice.
Go to article

Abstract

The combined effect of sulfur (S) and acid soluble aluminum (Als) content on precipitates and microstructures in grainoriented silicon steel were investigated. The results show that there are dominant AlN and a little amount of MnS-AlN composite in annealed hot-rolled band, and the amount of precipitates increases distinctly with increasing Als content, while S content plays a negligible role. The inhibitors that precipitate during hot band annealing can restrain the grain growth during hot band annealing and primary annealing, and the smaller grains of annealed hot-rolled band can contribute to the formation of {111} <112> texture during primary annealing. Lower S content is conducive to the formation of {111} <112> texture during primary annealing by promoting the formation of Goss texture during hot rolling.
Go to article

Abstract

Eutectoid growth, as the important reaction mechanism of the carbon steel heat treatment, is the basis to control the microstructure and performance. At present, most studies have focused on lamellar growth, and did not consider the nucleation process. Mainly due to the nucleation theory is inconclusive, a lot of research can support their own theory in a certain range. Based on the existing nucleation theory, this paper proposes a cooperative nucleation model to simulate the nucleation process of eutectoid growth. In order to ensure that the nucleation process is more suitable to the theoretical results, different correction methods were used to amend the model respectively. The results of numerical simulation show that when the model is unmodified, the lateral growth of single phase is faster than that of longitudinal growth, so the morphology is oval. Then, the effects of diffusion correction, mobility correction and ledges nucleation mechanism correction on the morphology of nucleation and the nucleation rate were studied respectively. It was found that the introduction of boundary diffusion and the nucleation mechanism of the ledges could lead to a more realistic pearlite.
Go to article

Abstract

Real-time monitoring of deformation of large structure parts is of great significance and the deformation of such structure parts is often accompanied with the change of curvature. The curvature can be obtained by measuring changes of strain, surface curve and modal displacement of the structure. However, many factors are faced with difficulty in measurement and low sensitivity at a small deformation level. In order to measure curvature in an effective way, a novel fibre Bragg grating (FBG) curvature sensor is proposed, which aims at removing the deficiencies of traditional methods in low precision and narrow adjusting. The sensor combines two FBGs with a specific structure of stainless steel elastomer. The elastomer can transfer the strain of the structure part to the FBG and then the FBG measures the strain to obtain the curvature. The performed simulation and experiment show that the sensor can effectively amplify the strain to the FBG through the unique structure of the elastomer, and the accuracy of the sensor used in the experiment is increased by 14% compared with that of the FBG used for direct measurement.
Go to article

Abstract

The main work of this paper focuses on the simulation of binary alloy solidification using the phase field model and adaptive octree grids. Ni-Cu binary alloy is used as an example in this paper to do research on the numerical simulation of isothermal solidification of binary alloy. Firstly, the WBM model, numerical issues and adaptive octree grids have been explained. Secondary, the numerical simulation results of three dimensional morphology of the equiaxed grain and concentration variations are given, taking the efficiency advantage of the adaptive octree grids. The microsegregation of binary alloy has been analysed emphatically. Then, numerical simulation results of the influence of thermo-physical parameters on the growth of the equiaxed grain are also given. At last, a simulation experiment of large scale and long-time has been carried out. It is found that increases of initial temperature and initial concentration will make grain grow along certain directions and adaptive octree grids can effectively be used in simulations of microstructure.
Go to article

Abstract

Lichens, as typical obligate associations between lichenized fungi and their photosynthetic partners, are dominant in Antarctica. Three Antarctic lichens, Ochrolechia frigida , Umbilicaria antarctica , and Usnea aurantiaco−atra with different growth forms, were sampled nearby the Great Wall Station, King George Island. Molecular data revealed that the photosynthetic algae in these three lichens were Trebouxia jamesii . The net photo − synthesis (Pn) of three individuals from these species, together with environmental factors such as light and temperature, were recorded by CO 2 gas exchange measurements using a CI−340 portable photosynthetic system in situ . Differences between T(leaf) (the temperature of the thalli) and T(air) (the air temperature) for these lichens were not consistent, which reflected that environment and the growth form of thalli could affect T(leaf) significantly. Strong irradiation was expected to have adverse effects on Pn of Ochrolechia frigida and Umbilicaria antarctica whose thalli spread flat; but this photoinhibition had little effect on Usnea aurantiaco−atra with exuberant tufted thallus. These results indicated that photo − synthetic activity in lichens was affected by the growth forms of thalli besides microhabitat factors. One species of lichenized alga could exhibit diversified types of photosynthetic behavior when it was associated with various lichenized fungi in different microhabitats. It will be helpful for understanding how lichens are able to adapt to and colonize in extreme environments.
Go to article

This page uses 'cookies'. Learn more