Porosity is one of the major defects in aluminum castings and results in a decrease of the mechanical properties of Al-Si alloys. It is induced by two mechanisms: solidification shrinkage and gas segregation. One of the methods for complex evaluation of macro and micro porosity in Al-Si alloys is using the Tatur test technique. This article deals with the evaluation of porosity with the help of Tatur tests for selected Al-Si alloys. These results will be compared with results obtained from the ProCAST simulation software.
Porosity is one of the major defects in aluminum castings, which results is a decrease of a mechanical properties. Porosity in aluminum alloys is caused by solidification shrinkage and gas segregation. The final amount of porosity in aluminium castings is mostly influenced by several factors, as amount of hydrogen in molten aluminium alloy, cooling rate, melt temperature, mold material, or solidification interval. This article deals with effect of chemical composition on porosity in Al-Si aluminum alloys. For experiment was used Pure aluminum and four alloys: AlSi6Cu4, AlSi7Mg0, 3, AlSi9Cu1, AlSi10MgCu1.
This paper considers the assessment of attenuation in aluminium alloys castings and in cast iron prepared by gravity casting method and by casting under pressure. The issue of ultrasound attenuation is important in setting the conditions of non-destructive (NDT) testing, especially in casted materials. The characteristics of the ultrasonic technique and ultrasonic attenuation and the calculation of the attenuation and the velocity of ultrasound are presented in the theoretical part of this paper. For experimental measurements, cylindrical castings from AlSi alloy (a hypoeutectic alloy with a silicon content of about 7% - AlSi7 and a eutectic alloy with a silicon content of about 12% - AlSi12) and from grey and ductile cast iron were made. The ultrasonic records of the casting control, the calculation of ultrasound attenuation for individual samples are listed and described in the experimental part. The evaluation of measurements and comparison of calculated ultrasound attenuation is at the end of this article.
The work deals with technology Patternless process that combines 3 manufacturing process mold by using rapid prototyping technology, conventional sand formation and 3D milling. It's unconventional technology that has been developed to produce large-sized and heavyduty castings weighing up to several tons. It is used mainly in prototype and small batch production, because eliminating production of models. The work deals with the production of blocks for making molds of gypsum and gypsum drying process technology Thermomold. Into blocks, where were made cavities by milling were casted test castings from AlSi10MgMn alloy by gravity casting. At machining of the mold cavity was varied feed rate of tool of cemented carbide. Evaluated was the surface roughness of test castings, that was to 5 micrometers with feed from 900 to 1300 mm/min. The dimensional accuracy of castings was high at feed rate of 1000 and 1500 mm/min did not exceed 0.025 mm.
First part of the article describes how we can by change of gating system achieve better homogeneity of product made by investment casting. Turbine engine flap was made by investment casting technology – lost wax casting. The casting process was realised in vacuum. The initial conditions (with critical occurrence of porosity) was simulated in ProCAST software. Numerical simulation can clarify during analysis of melt turbulent flow in gate system responsible for creation of entrained oxide films. After initial results and conclusions, the new gating system was created with subsequent turbulence analysis. The new design of gating system support direct flow of metal and a decrease of porosity values in observed areas was achieved. Samples taken from a casting produced with use of newly designed gating system was processed and prepared for metallography. The second part of article deals with identification of structural components in used alloy - Inconel 718. The Ni – base superalloys, which are combined unique physical and mechanical properties, are used in aircraft industry for production of aero engine most stressed parts, as are turbine blades.
The paper presents the problem of assessing the accuracy of reconstructing free-form surfaces in the CMM/CAD/CAM/CNC systems. The system structure comprises a coordinate measuring machine (CMM) PMM 12106 equipped with a contact scanning probe, a 3-axis Arrow 500 Vertical Machining Center, QUINDOS software and Catia software. For the purpose of surface digitalization, a radius correction algorithm was developed. The surface reconstructing errors for the presented system were assessed and analysed with respect to offset points. The accuracy assessment exhibit error values in the reconstruction of a free-form surface in a range of ± 0.02 mm, which, as it is shown by the analysis, result from a systematic error.
The tendencies of modern industry are to increase the quality of manufactured products, simultaneously decreasing production time and cost. The hybrid system combines advantages of the high accuracy of contact CMM and the high measurement speed of non-contact structured light optical techniques. The article describes elements of a developed system together with the steps of the measurement process of the hybrid system, with emphasis on segmentation algorithms. Additionally, accuracy determination of such a system realized with the help of a specially designed ball-plate measurement standard is presented.
This paper concerns the issues of measurement techniques, analysis and assessment of the machined surface geometric structure. The aim of this work was to show the application of surface analysis in diagnosing the causes of discrepancies occurring in the manufacturing process, which may result from ill-matched (poorly fitting) process parameters. An appropriate system of control and interpretation of results may allow early reaction to unfavorable trends (for example blunting of the tool) and prevention of undesirable defects. The subject of research was a waste basket used in the construction of retaining sewer systems. In this paper, the quality of the waste basket as well as its manufacturing process were analyzed and assessed. The research was carried out with the use of three measurement stands, i.e. optical microscopy (OM), scanning electron microscopy (SEM) and white light interferometer (WLI). The surface analysis proved to be important from the viewpoint of outlining the production process as well as improving the product quality. The software used for topographical analysis appeared to be significant for the success of the analysis, providing notable economic effects, namely the lack of defects.
Improvements of modern manufacturing techniques implies more efficient production but also new challenges for coordinate metrologists. The crucial task here is a coordinate measurement accuracy assessment. It is important because according to technological requirements, measurements are useful only when they are stated with their accuracy. Currently used methods for the measurements accuracy estimation are difficult to implement and time consuming. It is therefore important to implement correct and validated methods that will also be easy to implement. The method presented in this paper is one of them. It is an on-line accuracy estimation method based on the virtual CMM idea. A model is built using a modern LaserTracer system and a common test sphere and its implementation lasts less than one day. Results obtained using the presented method are comparable to results of commonly used uncertainty estimation methods which proves its correct functioning. Its properties predispose it to be widely used both in laboratory and industrial conditions.
This elaboration presents the method of virtual positioning of the construction of an endoprosthesis of hip joint in a patient’s pelvis and femoral bone, reconstructed on the basis of imaging obtained from computer tomography. It is based on the matching of an implant to individual anatomical-biomechanical conditions. The method is established on the following procedures: diagnostic, spatial modeling, virtual measuring and targeted biometrological application for the model of bone structures. The final effect of the completed procedures is selection and optimal positioning of the endoprosthesis of hip joint before a planned medical intervention. The determined geometrical parameters of bone structures and settled positioning of the endoprosthesis can create data for the system of computer navigation.