The BeiDou navigation satellite system (BDS) is one of the four global navigation satellite systems. More attention has been paid to the positioning algorithm of the BDS. Based on the study on the Kalman filter (KF) algorithm, this paper proposed a novel algorithm for the BDS, named as the minimum dispersion coefficient criteria Kalman filter (MDCCKF) positioning algorithm. The MDCCKF algorithm adopts minimum dispersion coefficient criteria (MDCC) to remove the influence of noise with an alpha-stable distribution (ASD) model which can describe non-Gaussian noise effectively, especially for the pulse noise in positioning. By minimizing the dispersion coefficient of the positioning error, the MDCCKF assures positioning accuracy under both Gaussian and non-Gaussian environment. Compared with the original KF algorithm, it is shown that the MDCCKF algorithm has higher positioning accuracy and robustness. The MDCCKF algorithm provides insightful results for potential future research.
The work reports on the development of random three-dimensional Laguerre-Voronoi computational models for open cell foams. The proposed method can accurately generate foam models having randomly distributed parameter values. A three-dimensional model of ceramic foams having pre-selected cell volumes distribution with stochastic coordinates and orientations was created in the software package ANSYSTM. Different groups of finite element models were then generated using the developed foam modeling procedure. The size sensitivity study shows that each of foam specimens at least contains 125 LV-cells. The developed foam models were used to simulate the macroscopic elastic properties of open cell foams under uni-axial and bi-axial loading and were compared with the existing open cell foam models in the literature. In the high porosity regime, it is found that the elastic properties predicted by random Laguerre-Voronoi foam models are almost the same as those predicted by the perfect Kelvin foam models. In the low porosity regime the results of the present work deviate significantly from those of other models in the literature. The results presented here are generally in better agreement with experimental data than other models. Thus, the Laguerre-Voronoi foam models generated in this work are quite close to real foam topology and yields more accurate results than other open cell foam models.
This study proposes a surface profile and roughness measurement system for a fibre-optic interconnect based on optical interferometry. On the principle of Fizeau interferometer, an interference fringe is formed on the fibre end-face of the fibre-optic interconnect, and the fringe pattern is analysed using the Fast Fourier transform method to reconstruct the surface profile. However, as the obtained surface profile contains some amount of tilt, a rule for estimating this tilt value is developed in this paper. The actual fibre end-face surface profile is obtained by subtracting the estimated tilt amount from the surface profile, as calculated by the Fast Fourier transform method, and the corresponding surface roughness can be determined. The proposed system is characterized by non-contact measurement, and the sample is not coated with a reflector during measurement. According to the experimental results, the difference between the roughness measurement result of an Atomic Force Microscope (AFM) and the measurement result of this system is less than 3 nm.
Owing to the dramatic change in the thermal conductivity of 4He when its temperature crosses the transition of superfluid (HeI) and normalfluid (HeII), a sealed-cell with a capillary is used to realize the lambda transition temperature, Tλ. A small heat flow is controlled through the capillary of the sealed-cell so as to realize the coexistence of HeI and HeII and maintain the stay of HeI/HeII interface in the capillary. A stable and flat lambda transition temperature "plateau" is obtained. Because there is a depression effect of Tλ caused by the heat flow through the capillary, a series of heat flows and several temperature plateaus are made and an extrapolation is applied to determine Tλ with zero heat flow. A rhodium-iron resistance thermometer with series number A34 (RIRT A34) has been used in 24 Tλ -realization experiments to derive Tλ with a standard deviation of 0.022mK, which proves the stability and reproducibility of Tλ.
Canine distemper virus (CDV) infects wild and domestic Canidae worldwide. The hemag- glutinin (H) gene has the highest genetic variation in the genome of this virus. Thus, the H gene is commonly used for lineage identification and genetic analyses. In order to study the genetic characteristics and pathogenicity of CDV strains prevalent in China, 132 samples were collected from domestic dogs with suspected CDV infection, 58 samples were confirmed to be positive, and the H gene was successfully amplified from 15 samples. The epidemic strain was identified as type Asia-1 and the novel mutations, A51T, V58I, R179K and D262N, were detected in this strain. Isolated strains, BJ16B53, BJ16B14, and BJ17B8, were used for an animal infection experiment in raccoon dogs. BJ16B53 and BJ16B14 were found to cause clinical symptoms, death, and exten- sive lesions in various organs. These results are expected to facilitate the development of effective strategies to monitor and control CDV infection in China.
An efficient system of micropropagation via somatic embryogenesis from root-derived callus was established in Arabica coffee (Coffea arabica L.). Twenty-six callus lines were induced on MS (Murashige and Skoog, 1962) medium supplemented with combinations of NAA (0, 0.1, 0.5, 1 and 2 mg/L) plus BA (0, 1 and 2 mg/L), or 2,4-D (0, 0.1, 0.5, 1 and 2 mg/L) plus TDZ (0, 1 and 2 mg/L). Subsequently, two types of somatic embryos were obtained from callus cultures and named S-type and I-type embryos. The S-type embryos were obtained from an 18-monthold callus line which was induced and maintained at 2 mg/L TDZ and 0.1 mg/L 2,4-D near the end of each period of the subculture. These embryos have a developmental barrier, which did not pass through the torpedo stage and could be overcome by a supplement of 2 or 5 mg/L BA. The I-type embryos were induced from 3-month-old callus when transferred onto induction media, i.e., MS supplemented with TDZ (2 and 5 mg/L) plus 2,4-D (0 and 0.1 mg/L). The significantly highest response, i.e., 13.3 embryos per callus clump was obtained at 2 mg/L TDZ. In this study, the results reveal that TDZ has a crucial effect on embryogenic callus induction, proliferation and subsequent somatic embryogenesis.
Culture gas atmosphere is one of the most important factors affecting embryo development in vitro. The main objective of this study was to compare the effects of CO concentration on the subsequent pre-implantation developmental capacity of pig embryos in vitro, including embryos obtained via parthenogenesis, in vitro fertilization (IVF), and intracytoplasmic sperm injection (ICSI). Pig embryos were developed in four different CO2 concentrations in air: 3%, 5%, 10%, or 15%. The cleavage rate of pig parthenogenetic, IVF, or ICSI embryos developed in CO2 concen- trations under 5% was the highest. There were no significant differences in the oocyte cleavage rate in ICSI embryos in CO2 concentrations under 3% and 5% (p>0.05). However, as CO2 levels increased (up to 15%) the blastocyst output on day 7, from parthenogenetic, IVF, and ICSI em- bryos, decreased to 0%. These findings demonstrate that CO2 positively affects the developmen- tal capacity of pig embryos. However, high or low CO2 levels do not significantly improve the developmental capacity of pig embryos. The best results were obtained for all of the pig embryos at a 5% CO2 concentration.
This paper proposes an improved method of solving the permutation problem inherent in frequency-domain of convolutive blind source separation (BSS). It combines a novel inter-frequency dependence measure: the power ratio of separated signals, and a simple but effective bin-wise permutation alignment scheme. The proposed method is easy to implement and surpasses the conventional ones. Simulations have shown that it can provide an almost ideal solution of the permutation problem for a case where two or three sources were mixed in a room with a reverberation time of 130 ms.
Urethane foam mattresses are commonly used as cushioning when placing panel flooring on the floor slab of a building. Urethane foam consists of elastic fibres with pores. Both elements can affect the performance of the insulation against impact sounds. However, these effects have not yet been detailed, and they may change if the material properties or constitution of the fibres and pores in the cushioning change. In this paper, we propose an analytical model for use in evaluating the performance of insulation against floor impact sound. This model was used to examine the contribution of the pores versus the elastic fibres to wave transmissions from the flooring surface to the slab. The results reveal that the constitution of the foam (either open or closed cells of pores) and the thickness and hardness of the cushion layer strongly affect the sound insulation performance of the floor.
Azo dye wastewater treatment is urgent necessary nowadays. Electrochemical technologies commonly enable more efﬁcient degradation of recalcitrant organic contaminants than biological methods, but those rely greatly on the energy consumption. A novel process of bioﬁlm coupled with electrolysis, i.e., bioelectrochemical system (BES), for methyl orange (MO) dye wastewater treatment was proposed and optimization of main inﬂuence factors was performed in this study. The results showed that BES had a positive effect on enhancement of color removal of MO wastewater and 81.9% of color removal efﬁciency was achieved at the optimum process parameters: applied voltage of 2.0 V, initial MO concentration of 20 mg/L, glucose loads of 0.5 g/L and pH of 8.0 when the hydraulic retention time (HRT) was maintained at 3 d, displaying an excellent color removal performance. Importantly, a wide range of effective pH, ranging from 6 to 9, was found, thus greatly favoring the practical application of BES described here. The absence of a peak at 463 nm showed that the azo bond of MO was almost completely cleaved after degradation in BES. From these results, the proposed method of biodegradation combined with electrochemical technique can be an effective technology for dye wastewater treatment and may hopefully be also applied for treatment of other recalcitrant compounds in water and wastewater.
Canine parvovirus (CPV) causes acute gastroenteritis in domestic dogs, cats, and several wild carnivore species. In this study, the full-length VP2 gene of 36 CPV isolates from dogs and cats infected between 2016 and 2017 in Beijing was sequenced and analyzed. The results showed that, in dogs, the new CPV-2a strain was the predominant variant (n = 18; 50%), followed by the new CPV-2b (n = 6; 16.7%) and CPV-2c (n = 3; 8.3%) strains, whereas, among cats, the predominant strain was still CPV-2 (n = 9; 25%). One new CPV-2a strain, 20170320-BJ-11, and two CPV-2c strains, 20160810-BJ-81 and 20170322-BJ-26, were isolated and used to perform experimental infections. Multiple organs of beagles that died tested PCR positive for CPV, and characteristic histopathological lesions were observed in organs, including the liver, spleen, lungs, kidneys, small intestines, and lymph nodes. Experimental infections showed that the isolates from the epidemic caused high morbidity in beagles, indicating their virulence in animals and suggesting the need to further monitor evolution of CPV in China.
This paper is devoted to measuring the continuous diagnosis capability of a system. A key metric and its calculation models are proposed enabling us to measure the continuous diagnosis capability of a system directly without establishing and searching the sequential fault tree (SFT) of the system. At first a description of a D matrix is given and its metric is defined to determine the weakness of a continuous diagnosis. Then based on the definition of a sequential fault combination, a sequential fault tree (SFT) is defined with its establishment process summarized. A key SFT metric is established to measure the continuous diagnosis capability of a system. Two basic types of dependency graphical models (DGMs) and one combination type of DGM are selected for characteristics analysis and establishment of metric calculation models. Finally, both the SFT searching method and direct calculation method are applied to two designs of one type of an auxiliary navigation equipment, which shows the high efficiency of the direct calculation method.