Applied sciences

Bulletin of the Polish Academy of Sciences: Technical Sciences

Content

Bulletin of the Polish Academy of Sciences: Technical Sciences | 2008 | vol. 56 | No 3 |

Abstract

Iterative learning control is a technique especially developed for application to processes which are required to repeat the same operation over a finite duration. The exact sequence of operation is that the task is completed, the process is reset and then the operation is repeated. Applications are widespread among many industries, e.g. a gantry robot which is required to place items on a conveyor under synchronization as part of a food manufacturing process. In effect, iterative learning control exploits the fact that once a single execution of the task is complete then the input control action and output response produced are available to update the control input for the next trial and thereby sequentially improve performance. Moreover, it may be possible to undertake the required computations during the time between completing one trial and the start of the next. This paper gives an overview of some very significant recent progress in this general area, including results from experimental benchmarking, and also some areas for on-going/future research are outlined.

Go to article

Abstract

Pulsed laser deposition technique was applied for covering elastic cast-polyurethane membranes with titanium nitride and boron nitride layers. The deposition process was realized using a Nd:YAG laser with Qswitch in stages; firstly the membranes were coated with ultra-thin titanium nitride layer (TixN) by evaporation of a metallic titanium disk in nitrogen gas atmosphere and then a layer of boron nitride (BN) was deposited by ablation of hexagonal h-BN target in argon atmosphere. The surface morphology was observed by scanning electron microscopy. Chemical composition was analyzed by energy dispersive X-ray spectrometry. The phase analysis was performed by means of grazing incidence X-ray diffraction and attenuated total reflection infrared spectroscopy. The crystallographic texture was measured. The wear test was performed by pin-on-disk method. Hexagonal boron nitride layers with (0001)[uvtw] texture with flake-like grains were fabricated. The structure and texture of boron nitride was identical irrespectively of substrate roughness or BN thickness. Pin-on-disk wear tests showed that the coatings effectively decreased the friction coefficient from two to even four times comparing to pure polyurethane and polyurethane covered with graphite. This proved that deposited layers can replace graphite as a lubricating material used to protect polymer surfaces.

Go to article

Abstract

Hybryd PLD method was used for deposition high quality thin Ti, TiN, Ti(C,N) and DLC coatings. The kinetic energy of the evaporated particles was controlled by application of variation of di erent reactive and non reactive atmospheres during deposition. The purpose was to improve adhesion by building a bridge between the real ceramic coating and the substrate. A new layer composition layout was proposed by application of a bu er, starting layer. Advanced HRTEM investigation based on high resolution transmission electron microscopy was used to reveal structure dependence on specific atmosphere in the reactive chamber. New experimental technique to examine the crystallographic orientation based on X-ray texture tomography was applied to estimate contribution of the atmosphere to crystal orientation. Using Dictyostelium discoideum cells as a model organism for specific and nonspecific adhesion, kinetics of shear flow-induced cell detachment was studied. For a given cell, detachment occurs for critical stress values caused by the applied hydrodynamic pressure above a threshold. Cells are then removed from the substrate with an apparent first-order rate reaction that strongly depends on the stress. The threshold stress depends on cell size and physicochemical properties of the substrate, but it is not a ected by depolymerization of the actin and tubulin cytoskeleton.

Go to article

Abstract

The dual core bit-byte CPU must be equipped with properly designed circuits, providing interface between the two processor units, and making it possible to exploit all its advantages like versatility of the byte unit and speed of the bit unit. First of all, the interface circuits should be designed in such a way, that they don’t disturb maximally parallel operation of the units, and that the CPU as a whole works in the same manner as in a standard PLC. The paper presents hardware solutions supporting effective operation of PLC CPU-s. Possibilities of solving problems concerning data exchange between a CPU and peripheral circuits were presented, with a special stress on timers and counters, and also on data exchange between the bit unit and the byte unit. The objective of the proposed solutions is to decrease the time necessary for a CPU to access its peripheries.

Go to article

Abstract

The paper deals with the application of the feed-forward and cascade-forward neural networks to mechanical state variable estimation of the drive system with elastic coupling. The learning procedure of neural estimators is described and the influence of the input vector size and neural network structure to the accuracy of state variable estimation is investigated. The quality of state estimation by neural estimators of different types is tested and compared. The simple optimisation procedure is proposed. Optimised neural estimators of the torsional torque and the load machine speed are tested in the open-loop and closed-loop control structure of the drive system with elastic joint, with additional feedbacks from the shaft torque and the difference between the motor and the load speeds. It is shown that torsional vibrations of the two-mass system are damped effectively using the closed-loop control structure with additional feedbacks obtained from the developed neural estimators. The simulation results are confirmed by laboratory experiments.

Go to article

Abstract

The significance of the famous Shannon's publication "A mathematical theory of communication" is discussed. The author states that this theory was a breakthrough for the times it was created. The present-day communications is so highly developed, that some old maxims should be up-dated, particularly the definition of the lower bound of signal reception. The author claims that this bound is no longer a constant value, ln(2), as the Shannon's theory states, but depends on many factors such, as the ratio of bandwidth-to-information transmission rate, the class of a receiver (adaptive, cognitive, MIMO1), the kind of reception system (on-line or off-line), and - of course - on the characteristics of noise, including entropy. Then, an absolute limit (Eb/N0)abs = 0 is suggested. An example of an advanced adaptive system approaching this bound is given.

Go to article

Abstract

The paper presents magnetic fluid as an excellent material platform for producing more complex magnetic drug delivery systems. In addition, the paper discusses the nanoparticle morphological (electron microscopy) and structural (X-ray diffraction) characterizations. M ossbauer spectroscopy and photoacoustic spectroscopy are revisited as key tools in the characterization of the magnetic core and diamagnetic shell of the magnetic nanoparticle, respectively.

Go to article

Abstract

The present investigation is concerned with the reflection in thermo-microstretch elastic solid in the presence of a transverse magnetic field, at the boundary surface. The generalized theories of thermoelasticity developed by Lord and Shulman [1](L-S) and Green and Lindsay [2](G-L) theories have been used to investigate the problem. The variations of amplitude ratios with angle of incidence have been shown graphically. It is noticed that the amplitude ratios of the reflected waves are affected by magnetic field, stretch and thermal properties of the medium.

Go to article

Abstract

A new class of positive fractional 2D hybrid linear systems is introduced. The solution of the hybrid system is derived. The classical Cayley-Hamilton theorem is extended for fractional 2D hybrid systems. Necessary and sufficient conditions for the positivity are established.

Go to article

Abstract

In the paper finite-dimensional time-variable dynamical control systems described by linear stochastic ordinary differential state equations with single time-variable point delay in the control are considered. Using notations, theorems and methods taken directly from deterministic controllability problems necessary and sufficient conditions for different kinds of stochastic relative controllability in a given time interval are formulated and proved. It will be proved that under suitable assumptions relative controllability of a deterministic linear associated dynamical system is equivalent to stochastic relative exact controllability and stochastic relative approximate controllability of the original linear stochastic dynamical system. Some remarks and comments on the existing results for stochastic controllability of linear dynamical systems are also presented.

Go to article

Abstract

A novel phase shift full bridge (PSFB) converter with voltage-doubler and decoupling integrated magnetics in photovoltaic (PV) systems is proposed. Considering the demand that the output voltage is higher than the input voltage in PV systems, the voltage-doubler is added to achieve higher voltage gain compared with the traditional PSFB. In order to avoid current oscillation caused by the voltage-doubler and obtain the wide zero voltage switching (ZVS) ranges, an external inductor is imposed on the circuit. Especially, to obtain much higher power density, the external inductor and transformer are integrated into one magnetic core. The operation and voltage gain of proposed converter are analyzed. Also, in order to reveal the effects the integrated magnetics gives to the converter, the decoupling condition and the expression of leakage inductor of integrated magnetics are obtained in detail. Finally a 100 W prototype converter is made and the experimental results are given to verify the analysis.

Go to article

Abstract

Hydrogen (H2) and liquid petroleum gas (LPG) sensing properties of SnO2 thin films obtained by direct oxidation of chemically deposited SnS films has been studied. The SnS film was prepared by a chemical technique called SILAR (Successive Ionic Layer Adsorption and Reaction). The sensor element comprises of a layer of chemically deposited SnO2 film with an overlayer of palladium (Pd) sensitiser. The Pd sensitiser layer was also formed following a chemical technique. The double layer element so formed shows significantly high sensitivity to H2 and LPG. The temperature variation of sensitivity was studied and the maximum sensitivity of 99.7% was observed at around 200°C for 1 vol% H2 in air. The response time to target gas was about 10 seconds and the sensor element was found to recover to its original resistance reasonably fast. The maximum sensitivity of 98% for 1.6 vol% LPG was observed at around 325°C. The sensor response and recovery was reasonably fast (less than one minute) at this temperature.

Go to article

Editorial office

Editor-in-Chief:

T. Kaczorek, Warsaw University of Technology

Deputy Editor-in Chief:

M. Kaźmierkowski, Warsaw University of Technology

A. Rogalski, Division IV Technical Sciences PAN

Board of Co-editors:

Artificial and Computational Intelligence

S. Osowski and B. Sawicki, Warsaw University of Technology

Biomedical Engineering and Biotechnology

A. Liebert and R. Maniewski, Institute of Biocybernetics and Biomedical Engineering PAN

Civil Engineering

L. Czarnecki, Building Research Institute, ITB, Warsaw

Control, Robotics and Informatics

J. Klamka and A. Babiarz, Silesian Technical University

A. Borkowski, Institute of Fundamental Technological Research PAN

Electronics, Telecommunication and Optoelectronics

M. Mrozowski and A. Lamęcki, Gdansk University of Technology

W. Woliński, Warsaw University of Technology

Mechanical and Aeronautical Engineering, Thermodynamics

A. Styczek and A. Tylikowski, Warsaw University of Technology

Materials Science and Nanotechnology

B. Major and P. Czaja, Institute of Metallurgy and Materials Science PAN

T.A. Kowalewski and B. Blachowski, Institute of Fundamental Technological Research PAN

Power Systems and Power Electronics

M.P. Kazmierkowski, Warsaw University of Technology

International Editorial Advisory Board

I.V. Alexandrov, Ufa State Aviation Technical University, Russia

R. Asthana, University of Wiscontin-Stout, Menomonie, USA

Xu Binshi, China Association of Plant Engineering, Beijing, P.R. China

F. Blaabjerg, Aalborg University, Denmark

C. Cecati, University of L’Aquila, Italy

A. Cichocki, RIKEN Institute, Tokyo, Japan

M. David, National Polytechnique de Toulouse, France

R. Ebner, Materials Centre Leoben, Leoben, Austria

E. Fornasini, University of Padova, Padova, Italy

L.G. Franquelo, University of Sevilla, Spain

M. Gad-el-Hak, Virginia Commonwealth University, Richmond, USA

D. van Gemert, Catholic University Leuven, KU Leuven, Belgium

L. Keviczky, Hungarian Academy of Sciences, Budapest, Hungary

V. Kučera, Czech Technical University in Prague, Prague, Czech Republic

R. Kennel, Technical University Munich, Germany

E. Levi, Liverpool John Moore University, UK

G. Maier, Technical University of Milan, Milan, Italy

K.F. Man, City University of Hong Kong,

H.A. Mang, Austrian Academy of Sciences, Vienna, Austria

H. Mihashi, Tohoku University, Aoba-ku, Sendai, Japan

S. Mindess, University of British Columbia, Vancouver, Canada

D.A. Mlynski, University of Karlsruhe, Karlsruhe, Germany

A.S. Nowak, University of Michigan, Ann Arbor, USA

K. Ohnishi, Keio University, Yokohama, Japan

A. Öberg, Linköping University, Linköping, Sweden

W. Pedrycz, University of Alberta, Canada

S. Przemieniecki, University of South Florida, Tampa, USA

M. Razeghi, Northwestern University, Evanston, USA

J. Rodriguez, Technical University of Federico Santa Maria, Valparaiso, Chile

J.V. Sloten, Catholic University Leuven, Leuven, Belgium

B.M. Wilamowski, University of Auburn, Alabama, USA

W. Włosiński, Warsaw University of Technology, Warsaw, Poland

A.L. Yarin, Institute of Illinois at Chicago, USA

Du Xiangwan, Chinese Academy of Engineering, China

J. Żurada, Department of Computer Engineering, University of Louisville, USA

Contact

Editorial Office:

Pałac Kultury i Nauki

Wydział IV Nauk Technicznych PAN

Pl. Defilad 1

PL 00-901 Warszawa

Mrs Ewa Trojanowska

bulletinpas.et@gmail.com

Instructions for authors

Instructions for Authors

About the Journal

The Bulletin of the Polish Academy of Sciences: Technical Sciences (Bull. Pol. Ac.: Tech.) is published by the Division IV: Engineering Sciences of the Polish Academy of Sciences. The journal is peer‐reviewed and is published both in printed and electronic form (http://www.czasopisma.pan.pl/bpas). It is established for the publication of original high quality papers from multidisciplinary Engineering sciences with the following topics preferred:

• Artificial and Computational Intelligence,

• Biomedical Engineering and Biotechnology,

• Civil Engineering,

• Control, Informatics and Robotics,

• Electronics, Telecommunication and Optoelectronics,

• Mechanical and Aeronautical Engineering, Thermodynamics,

• Material Science and Nanotechnology,

• Power Systems and Power Electronics.

General data:

Format of the journal – A4 printed and electronic form,

Paper type – offset

Colourfulness – full colour at an extra charge,

The volume of the journal – 200 pages (ca 20 papers) + 4 cover pages,

Frequency of publication – bimonthly,

ISSN: 0239-7528 (print version),

ISSN: 2300-1917 (on line version),

DOI: 10.2478/bpasts

Abbreviations/Acronym:

Journal citation: Bull. Pol. Ac.: Tech.

ISO: Bull. Pol. Acad. Sci.-Tech. Sci.,

JCR Abbrev: B POL ACAD SCI-TECH

Acronym in the Editorial System: BPASTS

Journal Metrics:

JCR Impact Factor 2017: 1.361

5 Year Impact Factor 2017: 1.323

SCImago Journal Rank (SJR) 2015: 0.526

Source Normalized Impact per Paper (SNIP) 2015: 1.208

Impact per Publication (IPP) 2015: 1.158

The Polish Ministry of Science and Higher Education 2017: 25 points

Manuscript types:

Invited reviews presenting the state of the knowledge and/or devoted to novel topics,

• Refereed research papers reporting on original scientific or technological achievements,

• Refereed papers in special issues/sections serving as conference proceedings arranged by guest editors.

Special Section Policy

Proposals of original Special Sections within the scope of the Journal may be submitted to the Editorial Office. Special Section submission rules are described in detail at: Edytorial Systems

Guest Editor form needed for submitting a Special Section proposal: Edytorial systems

Manuscript Submission Policy

All manuscripts submitted for publication should be original. Manuscripts published or under consideration for publication elsewhere should not be submitted and will not be considered. Submission of a paper implies that it has not been published previously, that it is not under consideration for publication elsewhere, and that if accepted it will not be published elsewhere in the same form, in English or in any other language, without the written consent of the Publisher.

However, manuscripts based on papers published at related conferences and workshops proceedings may be submitted for consideration provided that: (1) the papers are not identical (similarity index must be below 50%), (2) the authors cite their earlier conference paper on which this new work is based, (3) the journal publication includes clearly shown novel elements (e.g., more comprehensive experiments).

Manuscript submission for review

The Bull. Pol. Ac.: Tech now employs a Web-based manuscript submission and peer-review tracking system called Editorial System. Authors must submit their manuscript electronically on the web: http://www.editorialsystem.com/bpasts/.

From this entry page, access can be obtained to all information required for the submission of a manuscript. First‐time users must create an Author’s account to obtain a user ID and password required to enter the system. All manuscripts receive individual identification codes that should be used in any correspondence with regard to the publication process. For the authors already registered in the Editorial System it is enough to enter their username and password to login as an author (Sign in).

Author(s) will be notified about registration and manuscript review process by e-mail.

The manuscripts must be uploaded as a single PDF file.

If you experience difficulties with the manuscript submission website, please contact the Copy Editor of the Bull. Pol. Ac.: Tech (Anna Jurkiewicz: bulletinPAS@gmail.com).Names of authors and their affiliation should be removed from the manuscripts for the review process in order to have a fair evaluation of their manuscript. All authors of the manuscript are responsible for its content; they must have agreed to its publication and have given the corresponding author the authority to act on their behalf in all matters pertaining to publication. The Corresponding Author is responsible for informing the coauthors of the manuscript status throughout the submission, review, and production process. All submitted papers are checked using iThenticate plagiarism detection software.

Manuscript preparation

1. The manuscript should be written in clear and concise English.

2. For manuscript preparation please use the attached Word or LaTeX template.

3. Please remember that in the .pdf version of the manuscript for evaluation process author(s) name(s) and affiliation should be removed.

4. Authors should consult a recent issue of the journal for style if possible.

Manuscript decision and Proofs

Manuscript evaluations are assigned one of four outcomes: Accept, Minor Revisions, Major Revisions, and Reject. Manuscripts with "Minor Revision" do not require a second review. All manuscripts receiving a "Major Revision" evaluation must be subjected to a second review. Rejected manuscripts are given no further consideration. Normally, manuscripts that receive a "Major Revision" decision have only one additional chance for revision and the revised version should be uploaded to the Editorial System within six weeks. If the author(s) failed to make satisfactory changes, the manuscript is rejected. On acceptance, manuscripts are subject to editorial amendment to suit house style.

Transfer of Copyright Agreement

Once the paper is initially accepted, the authors are assumed to have transferred the copyright of the paper to the publisher. Please fill the attached Form, sign, and add to the final version of the manuscript as separate .pdf file.

It is also available on the webpage

https://www.editorialsystem.com/files/bpasts/docs/BPASTS_License_to_publish.pdf.

Proofs will be sent to the author (first named author if no corresponding author is identified for multi-authored papers) and should be returned within 48 hours of receipt.

Fees for printing the article

The Bulletin of the Polish Academy of Sciences: Technical Sciences (Bull. Pol. Ac.: Tech.) is published in Open Access, which means that all papers are available on the internet to all users immediately upon publication free of charge for the readers. By submitting a paper for publication, authors declare that they are ready to cover the costs of printing their paper. In exchange for a fee for printing, the PDF file of published paper is available at the Open Access platform: http://www.degruyter.com/view/j/bpasts

National (foreign) authors:

• The flat fee of 1230 PLN (approximately 300 EUR) per paper

Exempt from the fee are:

• Authors of articles ordered by the Editorial Board (Invited papers)

50% discount for:

• Reviewers (who performed at least 5 reviews per year) – one paper per year

• Guest Editors (the discount is valid only within the special section guest-edited by the author)

Mandatory over-length charges of 200 PLN (approximately 50 EUR) per page

in case the paper exceeds

• 8 printed double-column pages for regular research papers,

• 8 printed double-column pages for Special issue/section papers,

• No limit for invited (review) papers.

In addition, each color page will be charged an additional fee according to the current cost of printing. Otherwise, the paper will be printed in black-white.

Information needed for Proforma Invoice

1. Author’s/Authors’ Last name(s), Name(s), e-mail

2. Title of the paper

3. Exact name of the payer (person / institution or other legal entity realizing the transfer)

4. Address of the payer

5. Taxpayer Identification Number (TIN, in Polish NIP) – only when paid by an institution or another legal entity!

Check list for final submission to the Bull. Pol. Ac.: Tech (after review)

1. Is your manuscript up to date? Did you include references, which were published while your manuscript was being processed? It is expected that at least 20% of references are to journal papers published in the last two years. Authors are welcome to consider reference papers published in the Bull. Pol. Ac.: Tech. In order to find the recent Bull. Pol. Ac.: Tech. papers please visit Open Access platform: http://www.czasopisma.pan.pl/dlibra/journal/95347

2. Is your title adequate and is your abstract correctly written? In the age of electronic publications it is not easy to be noticed! Authors have to do everything possible so the paper will be seen and read. Therefore, very careful wording should be used in the title and in the abstract. Without a proper and interesting title and abstract a great paper might never be downloaded from the de Gruyter platform http://www.czasopisma.pan.pl/dlibra/journal/95347 and read.

3. Does the manuscript clearly describe problem(s) and your accomplishments? Can your manuscript be shortened? Are there sentences or paragraphs that do not provide important information and can be eliminated?

4. Is the length of your manuscript adequate? Please notice that for long papers, you may face mandatory over length charges per page.

5. Please make sure that the fee for printing your manuscript is paid.

Open Access policy

Bulletin of the Polish Academy of Sciences: Technical Sciences jest czasopismem wydawanym w wolnym dostępie na licencji CC BY-NC-ND 4.0.

Bulletin of the Polish Academy of Sciences: Technical Sciences is an open access journal with all content available with no charge in full text version. The journal content is available under the licencse CC BY-NC-ND 4.0.

This page uses 'cookies'. Learn more