Applied sciences

Archives of Environmental Protection

Content

Archives of Environmental Protection | 2016 | vol. 42 | No 3 |

Abstract

Results of research on the hazard posed by polycyclic aromatic hydrocarbons contained in the dusts emitted from motor vehicle braking systems have been presented. The polycyclic aromatic hydrocarbons (PAHs) constitute a group of chemical compounds that pose a serious danger to the human health, chiefly because of their carcinogenic properties. Investigations into the issue of environmental pollution with polycyclic aromatic hydrocarbons generated by motor vehicle traffic were carried out in connection with the work being done at PIMOT on systems to reduce dust emission from motor vehicle braking systems. The investigations included determination of PAH contents of the dust emitted from vehicle braking systems as well as the PAH concentrations in the indoor air in a room with the stand for testing dust emissions from braking systems and in the duct to carry away gases from that room. Moreover, the PAH contents of soil were measured in the context of location of the soil sampling points in relation to traffic routes. The PAH contents were measured in Warsaw and in Zabrze. The investigation results confirmed that PAHs considered as being most harmful to the human health due to their carcinogenic properties were actually present in the dusts emitted from braking systems. The PAH contents of soil were found to be very sensitive to the location of the soil sampling points in relation to traffic routes and this is a confirmation of the thesis that motor traffic is an important source of environmental pollution with polycyclic aromatic hydrocarbons.

Go to article

Abstract

This study investigates cadmium (Cd) accumulation in the plant leaves of juglans regia (walnut) and cydonia oblanga (quince) trees related to traffic emissions on the highway roadside. The plant leaf samples were collected from 20 sites on the D-100 Highway roadside and washed with deionized water before analyzed. Determination of Cd was carried out using an inductively-coupled plasma-mass spectrometer after microwave digestion of the samples. Cd concentration on the plant leaves was found to be between 0.04–0.11 mg/kg. In order to determine the traffic-based emissions, vehicles were counted and an emission inventory was prepared. 0.18 tons of Cd was found to be delivered into the atmosphere every day. Cd accumulation depends on traffic density because there were no residential area and industrial plants. The distribution of Cd accumulation caused by traffic emissions was mapped by using a geographic information system (GIS). The maps showed that the Cd accumulation was high in the areas near the highway and then gradually decreased by moving away from the highway.

Go to article

Abstract

Persistent organic pollutants (POPs) originating from agrochemical industries have become an urgent environmental problem worldwide. Ordinary kriging, as an optimal geostatistical interpolation technique, has been proved to be sufficiently robust for estimating values with finite sampled data in most of the cases. In this study, ordinary kriging interpolation integrate with 3D visualization methods is applied to characterize the monochlorobenzene contaminated soil for an agrochemical industrial site located in Jiangsu province. Based on 944 soil samples collected by Geoprobe 540MT and monitored by SGS environmental monitoring services, 3D visualization in terms of the spatial distribution of pollutants in potentially contaminated soil, the extent and severity of the pollution levels in different layers, high concentration levels and isolines of monochlorobenzene concentrations in this area are provided. From the obtained results, more information taking into account the spatial heterogeneity of soil area will be helpful for decision makers to develop and implement the soil remediation strategy in the future.

Go to article

Abstract

Bioremediation is based on microorganisms able to use pollutants either as a source of carbon or in co-metabolism, and is a promising strategy in cleaning the environment. Using soil contaminated with petroleum products from an industrial area in Saudi Arabia (Jubail), and after enrichment with the polycyclic aromatic hydrocarbon (PAH) naphthalene, a Methylobacterium radiotolerans strain (N7A0) was isolated that can grow in the presence of naphthalene as the sole source of carbon. M. radiotolerans is known to be resistant to gamma radiation, and this is the first documented report of a strain of this bacterium using a PAH as the sole source of carbon. The commonly reported Pseudomonas aeruginosa (strain N7B1) that biodegrades naphthalene was also identified, and gas chromatography analyses have shown that the biodegradation of naphthalene by M. radiotolerans and P. aeruginosa did follow both the salicylate and phthalate pathways.

Go to article

Abstract

The paper presents preliminary results of investigations on a relationship between turbidity and other quality parameters in the SBR plant effluent. The laboratory tests demonstrated a high correlation between an effluent turbidity and a total suspended solids (TSS) concentration as well as between TSS and COD. Such a relationship would help to continuously monitor and control quality of a wastewater discharge using turbidity measurement.

Go to article

Abstract

Vegetable oils belong to a large group of substances consumed on a daily basis. World vegetable oil production is soaring, reducing the popularity of animal fats. Heavy metals pose a threat to human health. It is estimated that about 80% of the daily dose of heavy metals enters the human body through the consumption of food. Hence, it is necessary to monitor their concentrations in food products. Besides, the presence of heavy metals is thought to have possible negative influence on the quality of oils, especially on their taste and smell. Heavy metals may also accelerate the process of the rancidifiction of oils. Rapeseeds, soybean seeds and linseeds were selected for the analysis because they are one of the most popular oilseeds and at the same time they differ in terms of growing conditions. The analyses of different fractions and the ready-made product were also performed. The aim of the study was to determine the variation in concentrations of heavy metals, iron and manganese in different fractions during production. The significant concentrations of iron, manganese and zinc were observed in oilseeds. It was also shown that during different stages of oil refining the concentrations of metals decrease. The concentrations of metals are compared with those reported in literature.

Go to article

Abstract

Although the utilization of pesticides accounted for the group of persistent organic pollutants was banned years ago, a count of pesticides are still directly or indirectly a source of contamination in Europe. One of them, simazine is still allowed for use in the United States. Aim of this experiment was development of soil remediation method which could be utilized for degradation triazine class pesticides – simazine was an example used. A method for soil remediation based on ozonation processes in fluidized bed was successfully utilized for removal of simazine from contaminated soil. For the study soil highly contaminated with simazine up to the concentration of 0.05% w/w was used. Determination of the pesticide levels in soil was performed using extraction and gas chromatography. The method allowed 80% reduction of pesticide concentration level. The degradation of pesticide was accompanied with changes of physicochemical parameters of soil, i.e., decrease of pH and a increase of nitrates concentration. Despite changes in physicochemical properties of the soil, the developed method proved to be highly effective and can be successfully applied on an industrial scale.

Go to article

Abstract

Cd and Pb concentrations were measured in water, sediment and plant organs collected from selective sites located along the Bogdanka river (Poznań, Poland) in the 2012 growing season. The aim of the investigations was to monitor changes in heavy metal (HM) concentrations in different media over the periods, as well as to evaluate potential of two littoral plants, Phragmites australis and Typha angustifolia, for phytoremediation under natural conditions. Investigations revealed differences in HM concentrations in water and sediments. Higher values were observed in sediments than in water. The decrease in concentrations of both HMs in sediments was noted in two of the three selected water reservoirs during growing seasons, which suggests the possibility of their adsorption and accumulation by aquatic plants. Both investigated plant species accumulated ample amount of Cd and Pb in underground and aboveground plant tissues, however T. angustifolia revealed higher Cd translocation potential than P. australis. The latter revealed higher Pb accumulation in two lakes. Moreover, the translocation ratio was usually higher in spring, especially for Pb, in both plant species. Increasing level of pollution load index in sediment along the Bogdanka watercourse indicates accumulation of measured HMs.

Go to article

Abstract

To improve bioremediation of arsenic (As) contamination in soil, the use of microorganisms to efficiently reduce As and their assessment of genetic erosion by DNA damage using genomic template stability (GTS) evaluation and using RAPD markers were investigated. The five sites examined for microorganisms and contaminated soils were collected from affected gold mining areas. The highest As concentration in gold mining soil is 0.72 mg/kg. Microorganism strains isolated from the gold mining soil samples were tested for As removal capacity. Two bacterial isolates were identified by 16S rRNA gene sequence analysis and morphological characteristics as Brevibacillus reuszeri and Rhodococcus sp. The ability to treat As in nutrient agar (NA) at 1,600 mg/L and contaminated soil samples at 0.72 mg/kg was measured at 168 h, revealing more efficient As removal by B. reuszeri than Rhodococcus sp. (96.67% and 94.17%, respectively). Both species have the capacity to remove As, but B. reuszeri shows improved growth compared to the Rhodococcus sp. B. reuszeri might be suitable for adaptation and use in As treatment. The results are in agreement with their genetic erosion values, with B. reuszeri showing very little genetic erosion (12.46%) of culture in As concentrations as high as 1,600 mg/L, whereas 82.54% genetic erosion occurred in the Rhodococcus sp., suggesting that Rhodococcus sp. would not survive at this level of genetic erosion. Therefore, B. reuszeri has a high efficiency and can be used for soil As treatment, as it is capable to tolerate a concentration of 0.72 mg/kg and as high as 1,600 mg/L in NA.

Go to article

Abstract

The analysis of particle size in suspensions carried out with use of the laser diffraction method enables us to obtain not only information about the size of particles, but also about their properties, shape and spatial structure, determined basing on fractal dimension. The fractal dimension permits the evaluation of the interior of aggregates, at the same time showing the degree of complexity of the matter. In literature, much attention is paid to the evaluation of the fractal dimension of flocs in activated sludge, in the aspect of control of single processes, i.e. sedimentation, dehydration, coagulation or flocculation. However, results of research concerning the size of particles and the structure of suspensions existing in raw and treated sewage are still lacking. The study presents optical fractal dimensions D3 and particle size distributions measured with use of laser granulometer in raw and treated sewage and activated sludge collected from six mechanical-biological wastewater treatment plants located in the Lower Silesian region. The obtained test results demonstrate that wastewater treatment plants that use both sequencing batch reactors and continuous flow reactors are more efficient at capturing suspension particles of a size up to 30 μm and are characterized by an increased removal of particles of a size ranging from 30 μm to 550 μm to the outflow. Additionally, in the case of samples of treated sewage and activated sludge collected at the same location, at short intervals, similar particle distributions were observed. As far as the analysis of fractal dimensions is concerned, particles contained in the raw sewage suspension were characterized by the lowest values of the fractal dimension (median equals 1.89), while the highest values occurred in particles of activated sludge (median equals 2.18). This proves that the spatial structure of suspension particles contained in raw sewage was similar to a linear structure, with a large amount of open spaces, while the structure of particles contained in the activated sludge suspension was significantly more complex in the spatial aspect.

Go to article

Abstract

This study is aimed to investigate culturable airborne bacteria concentrations and the composition of methicillin-resistant staphylococci in eleven different locations on the basis of specific activities conducted within different parts of the European side of Istanbul. The highest bacterial levels were observed at the Bakirkoy station (1 100 CFU/m3) while the second highest levels were found at the Bahcelievler station (1 040 CFU/m3) in October; the lowest levels (10 CFU/m3) were measured at other different stations (Atakoy, Yesilkoy). Fifteen methicillin-resistant isolates [Staphylococcus hominis (n=11), S. cohnii spp. cohnii (n=2), S. sciuri (n=1), S. capitis spp. capitis (n=1)] were identified. The disc diffusion method was used to identify the antimicrobial resistance of these isolates, it was observed that the most common resistance was to penicillin (P) (n=11), doxycycline (DO) (n=4) and tetracycline (T) (n=5). None of the isolates was resistant to imipenem, amoxicillin/clavulanic acid, vancomycin (IPM, AMC, VA). However, multiple antimicrobial resistance was found to be 26.7%. The results of this study revealed the importance of isolated methicillin-resistant staphylococci in the stations with densely active human population and traffic, for public health. As a result, the importance of resting along known shorelines, where culturable airborne bacteria concentrations are much lower, and its importance for human health have been emphasized.

Go to article

Abstract

Landfill leachate makes a potential source of ground water pollution. Municipal waste landfill substratum can be used for removal of pollutants from leachate. Model research was performed with use of a sand bed and artificially prepared leachates. Effectiveness of filtration in a bed of specific thickness was assessed based on the total solids content. Result of the model research indicated that the mass of pollutants contained in leachate filtered by a layer of porous soil (mf) depends on the mass of pollutants supplied (md). Determined regression functions indicate agreement with empirical values of variable m′f. The determined regression functions allow for qualitative and quantitative assessment of influence of the analysed independent variables (m′d, l, ω) on values of mass of pollutants flowing from the medium sand layer. Results of this research can be used to forecast the level of pollution of soil and underground waters lying in the zone of potential impact of municipal waste landfill.

Go to article

Editorial office

Editors

Editor-in-Chief
Czesława Rosik-Dulewska

Editorial Advisory Board
Michał Bodzek
Katarzyna Juda-Rezler
Korneliusz Miksch

Assistant Editor
Katarzyna Panz

 

Editorial Board:

President:
Lucjan Pawłowski

Members:
Brian A. Bolto (Australia)
Hubert Bril (France)
Bart Van der Bruggen (Belgium)
Zhihong Cao (China)
Pen-Chi Chiang (R.O.C.)
Wolfgang Frenzel (Germany)
Reinhard F. Hüttl (Germany)
Piotr Kowalik (Poland)
Joanna Kyzioł-Komosińska (Poland)
Rajmund Michalski (Poland)
Anuska Mosquera Corral (Spain)
Takashi Nakamura (Japan)
Józef M. Pacyna (Norway)
Wim H. Rulkens (The Nederlands)
Corrado Sarzanini (Italy)
Hans Martin Seip (Norway)
Jan Siuta (Poland)
Jerzy Sobota (Poland)
Joanna Surmacz-Górska (Poland)
Jadwiga Szczepańska (Poland)
Christopher G. Uchrin (USA)
Tomasz Winnicki (Poland)
Xiaoping Zhu (USA)
Jerzy Zwoździak (Poland) 

Contact

Institute of Environmental Engineering of the Polish Academy of Sciences
ul.
M. Skłodowskiej-Curie 34, 41-819 Zabrze, Poland
Tel.: +48-32-271 64 81      Fax: +48-32-271 74 70
e-mail:
aep@ipis.zabrze.pl, katarzyna.panz@ipis.zabrze.pl

Instructions for authors

Instructions for Authors

Archives of Environmental Protection is a quarterly published jointly by the Institute of Environmental Engineering of the Polish Academy of Sciences and the Committee of Environmental Engineering of the Polish Academy of Sciences. Thanks to the cooperation with outstanding scientists from all over the world we are able to provide our readers with carefully selected, most interesting and most valuable texts, presenting the latest state of research in the field of engineering and environmental protection.

Scope

The Journal principally accepts for publication original research papers covering such topics as:

- Air quality, air pollution prevention and treatment;

- Wastewater treatment and utilization;

- Waste management;

- Hydrology and water quality, water treatment;

- Soil protection and remediation;

- Transformations and transport of organic/inorganic pollutants in the environment;

- Measurement techniques used in environmental engineering and monitoring;

- Other topics directly related to environmental engineering and environment protection.

The Journal accepts also authoritative and critical reviews of the current state of knowledge in the topic directly relating to the environment protection.

If unsure whether the article is within the scope of the Journal, please send an abstract via e-mail to: aep@ipis.zabrze.pl or justyna.drzymala@ipis.zabrze.pl

Preparation of the manuscript

The following are the requirements for manuscripts submitted for publication:

• The manuscript (with illustrations, tables, abstract and references) should not exceed 20 pages. In case the manuscript exceeds the required number of pages, we suggest contacting the Editor.

• The manuscript should be written in English.

• The manuscript ought to be submitted in doc or docx format in three files:

– text.doc – file containing the entire text, without title, keywords, authors names and affiliations, and without tables and figures;

– figures.doc – file containing illustrations with legends;

– tables.doc – file containing tables with legends;

• The text should be prepared in A4 format, 2.5 cm margins, 1.5 spaced, preferable using Time New Roman font with no less than 12 point. The text should be divided into sections and subsections according to general rules of manuscript editing. The proposed place of tables and figures insertion should be marked in the text.

• Legends in the figures should be concise and legible, using a proper font size so as to maintain their legibility after decreasing the font size. Please avoid using descriptions in figures, these should be used in legends or in the text of the article. Figures should be placed without the box. Legends should be placed under the figure and also without box.

• Tables should always be divided into columns. When there are many results presented in the table it should also be divided into lines.

• References should be cited in the text of an article by providing the name and publication year in brackets, e.g. (Nowak 2019). When a cited paper has two authors, both surnames connected with the word “and” should be provided, e.g. (Nowak and Kowalski 2019). When a cited paper has more than one author, surname of its first author, abbreviation ‘et al.’ and publication year should be provided, e.g. (Kowalski et al. 2019). When there are more than two publications cited in one place they should be divided with coma, e.g. (Kowalski et al. 2019, Nowak 2019, Nowak and Kowalski 2019). Internet sources should be cited like other texts - providing the name and publication year in brackets.

• References should be listed at the end of the article ordered alphabetically by surname of the first author. References should be made according to the following rules:

1. Journal:

Surnames and initials. (publication year). Title of the article, Journal Name, volume, number, pages, DOI.

For example:

Nowak, S.W., Smith, A.J. & Taylor, K.T. (2019). Title of the article, Archives of Environmental Protection, 10, 2, pp. 93–98, DOI: 10.24425/aep.2019.126330.

2. Book:

Surnames and initials. (publication year). Title, Publisher, Place and publishing year.

For example:

Kraszewski, J. & Kinecki, K. (2019). Title of book, Work & Sudies, Zabrze 2019.

3. Edited book:

Surnames and initials of text authors. (publishing year). Title of cited chapter, in: Title of the book, Surnames and initials of editor(s). (Ed.)/(Eds.). Publisher, Place, pages.

For example:

Reynor, J. & Taylor, K.T. (2019). Title of chapter, in: Title of the cited book, Kaźmierski, I. & Jasiński, C. (Eds.). Work & Studies, Zabrze, pp. 145–189.

4. Internet sources:

Surnames and initials or the name of the institution which published the text. (publication year). Title, (website address (accessed on)).

For example:

Kowalski, M. (2018). Title, (http://www.krakow.pios.gov.pl/publikacje/2009/ (03.12.2018)).

5. Patents:

Orszulik, E. (2009). Palenisko fluidalne, Patent polski: nr PL20070383311 20070910 z 16 marca 2009.

Smith, I.M. (1988). U.S. Patent No. 123,445. Washington, D.C.: U.S. Patent and Trademark Office.

6. Materials published in language other than English:

Titles of cited materials should be translated into English. Information of the language the materials were published in should be provided at the end.

For example:

Nowak, S.W. & Taylor, K.T. (2019). Title of article, Journal Name, 10, 2, pp. 93–98, DOI: 10.24425/aep.2019.126330. (in Polish)

Not more than 30 references should be cited in the original research paper.

Submission of the manuscript

By submitting the manuscript Author(s) warrant(s) that the article has not been previously published and is not under consideration by another journal. Authors claim responsibility and liability for the submitted article. The manuscripts should be submitted on-line using the Editorial System available at http://www.editorialsystem.com/aep. Authors are asked to propose at least 4 potential reviewers, including 2 from Poland, together with their e-mail addresses. The journal does not have article processing charges (APCs) nor article submission charges.

Review Process

All the submitted articles are assessed by the Editorial Board. If positively assessed by at least two editors, Editor in Chief, along with department editors selects two independent reviewers from recognized authorities in the discipline. Reviewers receive a text of the article (without personal data of Authors) and review forms applicable in the journal. In justified cases, reviewers receive additional questions regarding the article. Review process usually lasts from 1 to 4 months.

After completion of the review process Authors are informed of the results and - if both reviews are positive - asked to correct the text according to reviewers’ comments. Next, the revised work is verified by the editorial staff for factual and editorial content.

Acceptance of the manuscript

The manuscript is accepted for publication on grounds of the opinions of independent reviewers and approval of Editorial Board. Authors are informed about the decision and also asked to pay processing charges and to send completed declaration of the transfer of copyright to the editorial office.

Proofreading and Author Correction

All articles published in the Archives of Environmental Protection go through professional proofreading process. If there are too many language errors that prevent understanding of the text, the article is sent back to Authors with a request to correct the indicated fragments or - in extreme cases – to re-translate the text.

After proofreading the manuscript is prepared for publishing. The final stage of the publishing process is Author correction. Authors receive a page proof copy of the article with a request to make final corrections.

Article publication charges

The publication fee of an article in the Journal is:

• 20 EUR/80 zł per page (black and white or in gray scale),

• 30 EUR/120 zł per page (color).

Payments in Polish zlotys

Bank BGK

Account no.: 20 1130 1091 0003 9111 7820 0001

Payments in Euros

Bank BGK

Account no.: 20 1130 1091 0003 9111 7820 0001

IBAN: PL 20 1130 1091 0003 9111 7820 0001

SWIFT: GOSKPLPW

Authors are kindly requested to inform the editorial office of making payment for the publication, as well as to send all necessary data for issuing an invoice.

Open Access policy

Archives of Environmental Protection jest czasopismem wydawanym w wolnym dostępie na licencji CC BY-NC-SA 4.0.

Archives of Environmental Protection is an open access journal with all content available with no charge in full text version. The journal content is available under the licencse CC BY-NC-SA 4.

Additional information

Abstracting & Indexing

Archives of Environmental Protection is covered by the following services:

AGRICOLA (National Agricultural Library)

AGRIS

Arianta

Baidu Scholar

BazTech

CABI (over 50 subsections)

Chemical Abstracts Service (CAS) - CAplus

Chemical Abstracts Service (CAS) - SciFinder

CNKI Scholar (China National Knowledge Infrastructure)

CNPIEC

Dimensions

DOAJ (Directory of Open Access Journals)

EBSCO (relevant databases)

EBSCO Discovery Service

Engineering Village

FSTA - Food Science & Technology Abstracts

Genamics JournalSeek

GeoArchive

GeoRef

Google Scholar

Index Copernicus

Inspec

Japan Science and Technology Agency (JST)

J-Gate

Journal Citation Reports/Science Edition

JournalTOCs

KESLI-NDSL (Korean National Discovery for Science Leaders)

Microsoft Academic

Naviga (Softweco)

Primo Central (ExLibris)

ProQuest (relevant databases)

Publons

ReadCube

Reaxys

SCOPUS

Sherpa/RoMEO

Summon (Serials Solutions/ProQuest)

TDNet

TEMA Technik und Management

Ulrich's Periodicals Directory/ulrichsweb

WanFang Data

Web of Science - Biological Abstracts

Web of Science - BIOSIS Previews

Web of Science - Science Citation Index Expanded

WorldCat (OCLC)

This page uses 'cookies'. Learn more