Applied sciences

Archives of Electrical Engineering

Content

Archives of Electrical Engineering | 2010 | vol. 59 | No 1 - 2 September |

Abstract

This paper deals with an observer design for a p-cell chopper. The goal is to reduce drastically the number of sensors in such system by using an observer in order to estimate all the capacitor voltages. Furthermore, considering an instantaneous model of a p-cell chopper, an interconnected observer is designed in order to estimate the capacitor voltages. This is realized by using only the load current measurement. Simulation results are given in order to illustrate the performance of such observer. To demonstrate the validity of our approach, experimental results based on Digital Signal Processor (DSP) are presented.

Go to article

Abstract

Electrical circuits with state-feedbacks are addressed. It is shown that by suitable choice of the gain matrices of state-feedbacks it is possible to obtain the closed-loop system matrices with nilpotency indices equal to two and their state variables are linear functions of time. The considerations are illustrated by linear electrical circuits.

Go to article

Abstract

Results of 3-D of discharge channel displacement simulation, acquired by means of the Fluent program during one current half-period of AC arc, indicate that the obtained images of the phenomenon are qualitatively similar to those, recorded with a high-speed digital camera, while the computer simulation enables much a more comprehensive analysis of the acquired data. In addition to selected arc simulation frames and corresponding distributions of mass velocity vectors and current density vectors on a plane, the distributions of temperature, current density and mass velocity values are presented on the axis of the electrode arrangement model. The composite motion (continuous and jumping) of discharge channels was analyzed, taking into account mass displacement and matter state changes.

Go to article

Abstract

In the paper modeling of main inductances for mathematical models of induction motors is applied to study the effects caused by a rotor eccentricity and saturation effects. All three possible types of eccentricity: static, dynamic and mixed are modeled. The most important parameters describing rotor eccentricity include self and mutual inductances of the windings. The structural changes of the permeance function as a result of eccentricity appearance and the Fourier spectra of inductances in occurrence of saturation for each case are determined in the paper. The presented algorithm can be used for the diagnostically specialized models of induction motors.

Go to article

Abstract

The paper presents the probabilistic model of fibrillation currents containing two components with different frequencies. An analysis was conducted of the threat of ventricular fibrillation which occurs in consequence of the electric shock with the highest permissible contact shocking voltage of the network frequency (50 Hz), taking into account the threat caused by the second component of the voltage which has the frequency higher than the network frequency. The sample results of calculations apply to the probability of the ventricular fibrillation in case of a shock caused by the highest permissible contact shocking voltage, for the defined time of shock duration, without and with the participation of an additional voltage component with higher frequency. The formula has been presented for the calculation of the highest permissible contact shock voltages with taking into account the voltage component of the frequency higher than the network frequency. The results of calculations indicate that a considerable reduction of the highest permissible contact shock voltage is necessary in order to compensate for a growth of the ventricular fibrillation threat caused by the presence of an additional component with the frequency other the network frequency. This applies in particular to the long shock duration times and low frequencies (up to 500 Hz) of an additional component of the shocking voltage.

Go to article

Abstract

The paper describes high output induction motors driving large applications of heavy starting conditions. Heavy start is characterised by long accelerating time and occures in drives of hudge inertia torque, esspecially when performed at full load. The reliable operation of the motors depends on proper design and quality of rotor's cage. The aspects of thermal behaviour and electrodynamic forces have to be considered during the design of the motor for hard working conditions. In the paper the rotor with idle bars is investigated.

Go to article

Abstract

The paper presents an algorithm and software for the optimal design of permanent magnet brushless DC motors. Such motors are powered by DC voltage sources via semiconductor switches connected to the motor phase belts. The software is adjusted to the design of motors with NdFeB high energy density magnets. An attention has been given to issues important in the design of the motors, i.e., permanent magnet selection, structure of magnetic circuit, and armature windings. Particularly, precision of calculation of the permanent magnet operating point, visualization of selection process of the winding belts, and magnetic circuit dimensioning have been investigated. The authors have been trying to make the equations more specific and accurate than those presented in the literature. The user software interface allows changes in the magnetic circuit dimensions, and in the winding parameters. It is possible to examine simultaneously the influence of these changes on the calculation results. The software operates both with standard and inverted (outer rotor) motor structure. To perform optimization, a non-deterministic method based on the evolution strategy (ž + λ) - ES has been used.
Go to article

Abstract

This research presents a method for the simulation of the magneto-mechanical system dynamics taking motion and eddy currents into account. The major contribution of this work leans on the coupling the field-motion problem considering windings as the current forced massive conductors, modelling of the rotor motion composed of two conductive materials and the torque calculation employing the special optimal predictor combined with the modified Maxwell stress tensor method. The 3D model of the device is analysed by the time stepping finite element method. Mechanical motion of the rotor is determined by solving the second order motion equation. Both magnetic and mechanical equations are coupled in the iterative solving process. Presented method is verified by solving the TEAM Workshop Problem 30.
Go to article

Editorial office

Editor-in-Chief
Professor Andrzej Demenko, Poznan University of Technology, Poland

Deputy/ Managing Editor
Mariusz Barański, Ph.D., Poznan University of Technology, Poland
Łukasz Knypiński, Ph.D., Poznan University of Technology, Poland

Editorial Advisory Board
Chairman: Marian P. Kaźmierkowski, Warsaw, Poland
Secretary: Mariusz Jagieła, Opole, Poland

Members professors:
Anouar Belahcen, Espoo, Finland

Frede Blaabjerg,Aalborg, Denmark

Ion Boldea,Timisoara, Romania

Herbert De Gersem,Darmstadt, Germany

Jacek Gieras, Rockford, USA

Kay Hameyer, Aachen, Germany

Marian K. Kazimierczuk, Dayton, USA

Stefan Kulig, Dortmund, Germany

David A. Lowther, Montreal, Canada

Jacek Marecki, Gdańsk, Poland

José Rodríguez Pérez,Valparaíso, Chile

Ryszard Sikora, Szczecin, Poland

Zbigniew Styczyński, Magdeburg, Germany

Jan Sykulski, Southampton, UK

Sławomir Wiak, Łódź, Poland

 

Language Editor

Krystyna Guzek

Statistical Editor

Mariusz Barański, Poznan, Poland
Poznan University of Technology

Theme Editors

Jerzy Barglik, Gliwice, Poland
Professor at Silesian University of Technology

Zbigniew Lubosny, Gdansk, Poland
Professor at Gdańnk University of Technology

Marian Łukaniszyn, Opole, Poland
Professor at Opole University of Technology

Marian Pasko, Gliwice, Poland
Professor at Silesian University of Technology

Stanisław Piróg, Krakow, Poland
Professor at AGH University of Science and Technology

Henryka Danuta Stryczewska, Lublin, Poland
Professor at Lublin University of Technology

Jan Sykulski, Southampton, UK
Professor at University of Southampton

Adam Szelag, Warsaw, Poland
Professor at Warsaw University of Technology

Romulad Włodek, Krakow, Poland
Professor at AGH University of Science and Technology

Technical Editor :

Typesetting in LATEX: Drukarnia Braci Grodzickich Sp.j., 05-500 Piaseczno, ul. Geodetów 47a, Poland

Contact

All contributions should be addressed to the Editor-in-Chief or the Editorial Office:

Address of the Editorial Office:

Archives of Electrical Engineering
Piotrowo 3A (Room 612X)
60-965 Poznan, Poland
tel: (48-61) 665-26-36
fax: (48-61) 665-23-81
e-mail: aee@put.poznan.pl

Website: www.aee.put.poznan.pl

Instructions for authors

ARCHIVES OF ELECTRICAL ENGINEERING (AEE) (previously Archiwum Elektrotechniki), quarterly journal of the Polish Academy of Sciences is OpenAccess, publishing original scientific articles and short communiques from all branches of Electrical Power Engineering exclusively in English. The main fields of interest are related to the theory & engineering of the components of an electrical power system: switching devices, arresters, reactors, conductors, etc. together with basic questions of their insulation, ampacity, switching capability etc.; electrical machines and transformers; modelling & calculation of circuits; electrical & magnetic fields problems; electromagnetic compatibility; control problems; power electronics; electrical power engineering; nondestructive testing & nondestructive evaluation.,

Manuscript submission:

All manuscripts should be submitted electronically on Editorial System.

Submission of paper to the Archives of Electrical Engineering is understood to imply that the article is original, unpublished and is not being considered for publication elsewhere. All articles will be reviewed. Since 2013, Authors wishing to use the facility of colour printing should consult the editors.,

Template:

Microsoft Word is recommended as a standard word processor to prepare the paper to the AEE journal. If you use the LaTex format, please transfer your document to Microsoft Word and then use Template AEE.
Please use Template AEE to prepare your paper.

,

The reviewing process:

Each paper submitted for publication in Archives of Electrical Engineering is subjected to the following review procedure:
a) the paper is reviewed by the editor in chief or guest editor for general suitability for publication in AEE
b) if it is judged suitable two reviewers are selected and a double blind peer review process takes place
c) based on the recommendations of the reviewers, the editor then decides whether the paper should be accepted in its present form, revised or rejected
d) the author(s) is(are) informed by e-mail on the results of the reviewing procedure.
The papers are published on average within 3 months after acceptance.,

Requirements for preparation of manuscripts:

The manuscripts submitted for publication should not exceed 21 000 characters (ca. 12 pages of a manuscript written on an A4 sheet in Times New Roman, 10pt font size, single line spacing and 3.8 cm margins). The manuscripts, written in UK English, should be typed using Template AEE according to the following instructions and should include: a title page with the title of a manuscript, a short title; abstract; key words, text; list of references. A DOI number as well as received and revised data will be completed by Editor. When you open Template.doc, select "Print Layout" from the "View" menu in the menu bar (View > Print Layout). Then type over sections of Template.doc or cut and paste from another document and then use markup styles (Home > Styles). For example, the style at this point in the document is "main text").

All papers submitted for publication are assessed on the basis of the mutual anonymity rule as to the names of reviewers and authors. Authors' names and affiliations should not appear in the attached text/tables/figures.

If English is not your first language, ask an English-speaking colleague to proofread your manuscript. The manuscripts that fail to meet basic standards of literacy are likely to be immediately declined or after the language assessment, sent to the authors for linguistic improvement.

The manuscripts are published on average within 3 months after their acceptance.

Do not change the font sizes or line spacing to squeeze more text into a limited number of pages. Leave some open space around your figures.

The AEE journal publishes an ORCID for all authors. You will need a registered ORCID in order to submit your paper for peer review. ORCID registration is free and only takes a minute. Please note that ORCIDs will be added in the course of the author's proofreads.

,

Text:

The pages must be numbered consecutively. Articles should be divided into numbered sections, and if necessary subsections, preferably: Introduction, Material, Methods, Results, Conclusion and References. Any special characters (e.g. Greek, script, etc.) should be named in the margin where the character first occurs in the text. Names of species are to be accentuated with wavy underlining (italics). Equations should be numbered serially (1), (2), ... on the right side of the page. Footnotes should be avoided, if required, they should be used only for brief notes which do not fit well into the text. Figures and tables have to be included into the text. If table is typed on a separate page its position in the text should be marked. Abbreviations should be explained when they first appear in the text.,

Math:

Please use the Microsoft Equation 3.0 editor (comes with Microsoft Office 2007 and later versions) or the MathML editor as well as MathType editor to build an equation in your manuscript.
To insert an equation in Word, choose Insert, then Object. This will bring up a dropdown menu, where the Object option should be chosen again. Pressing it opens a popup window, where the Create New option has to be clicked. Scrolling down the window allows to find Microsoft Equation 3.0.

,

Equations:

Equations should be typed within the text, centred, and should be numbered consecutively throughout the text. Their numbers should be typed in parentheses, flush right. Equations should be referred to in text, e.g. (1), except at the beginning of a sentence: "Equation (1) is ...". All symbols appearing in equations have to be defined in the text, before or just after the equation.
If the symbols are written in Times New Roman use italic fonts. Symbols of vectors and matrices should be written in bold fonts. Do not italicize Greek fonts and mathematical symbols like e.g.: the derivative symbol d, max, min, etc. The indices of symbols that are indices themselves should be written in a clear manner.
Note that the equation is centered using a center tab stop. Please keep the same font in the formulas and text.,

Unit Symbols, Abbreviations:

Define abbreviations and acronyms the first time they are used in the text, even after they have been defined in the abstract. Abbreviations such as IEEE, SI, MKS, CGS, sc, dc, and rms do not have to be defined. Do not use abbreviations in the title or heads unless they are unavoidable.
Si units are recommended for use in formulas, drawings and tables., for example the SI unit for magnetic field strength H is A/m. Apply the center dot to separate compound units.
Do not mix complete spellings and abbreviations of units: "Wb/m2" or "webers per square meter," not "webers/m2." Spell units when they appear in text: "...a few henries…", not "...a few H…".
Use a zero before decimal points: "0.25," not ".25." Use "cm3," not "cc."
Unit Symbols, SI Prefixes as well as Abbreviations should be writing in accordance with the IEEE standard,

Tables, figures (illustrations) and captions:

The illustrations (line diagrams and photographs) should be suitable for direct reproduction. The lettering as well the details should have proportional dimensions to maintain their legibility after the usual reduction. All illustrations should be numbered consecutively (Fig. X). Tables are numbered with Arabic numerals.
All figures, figure captions, and tables in the text must be inserted into the correct places.
Figures, photos, tables or other parts of a manuscript that have previously appeared in another publication or are not the property of the authors must be properly acknowledged in the manuscript. Permission to republish these items must be obtained by the corresponding author from a person or institution holding the copyright, usually the publisher.
Authors are requested to send figures (diagrams, line drawings and photographic images) in separate computer files. JPG, PNG or TIF are the recommended file formats. Photographs, colour and greyscale figures should be at least at a resolution of 400dpi. Linear, including tables should be at a minimum of 600dpi.
All colour figures should be generated in the RGB or CMYK colour space, while greyscale images in the greyscale colour space.
When preparing your figures/graphics etc., we suggest the use of the Arial 8 point font for axis numbers and Arial 9 point font for axis names. Figures/graphics etc. can be prepared in one of two proposed ways - see Template AEE.
Tables are numbered with Arabic numerals. Use 9 point Times New Roman for the title of the table and 9 point Times New Roman for the filling of the table (9 in the case of symbols with subscripts).
AEE journal allows an author to publish color figures in e-version at no charge, and automatically convert them to grayscale for print versions. Authors wishing to use the facility of color printing should consult the editors.,

Conclusions:

A conclusion might elaborate on the importance of the work or suggest applications and extensions. Although a conclusion may review the main points of the manuscript, do not replicate the abstract as the conclusion.,

References:

References in text must be numbered consecutively by Arabic numerals placed in square brackets. Please make sure that you use full names of journals i.e. Archives of Electrical Engineering. Please ensure that all references in the Reference list are cited in the text and vice versa.
Please provide name(s) and initials of author(s), the title of the manuscript, editors (if any), the title of the journal or book, a volume number, the page range, and finally the year of publication in brackets.
You can use the rules presented on the site: IEEE standard

Examples of the ways in which references should be cited are given below:

Journal manuscript
[1] Author1 A., Author2 A., Title of paper, Title of periodical, vol. x, no. x, pp. xxx-xxx (YEAR).
example
[1] Steentjes S., von Pfingsten G., Hombitzer M., Hameyer K., Iron-loss model with consideration of minor loops applied to FE-simulations of electrical machines, IEEE Transactions on Magnetics. vol. 49, no. 7, pp. 3945-3948 (2013).
[2] Idziak P., Computer Investigation of Diagnostic Signals in Dynamic Torque of Damaged Induction Motor, Electrical Review (in Polish), to be published.
[3] Cardwell W., Finite element analysis of transient electromagnetic-thermal phenomena in a squirrel cage motor, submitted for publication in IEEE Transactions on Magnetics.

Conference manuscript
[4] Author A., Title of conference paper, Unabbreviated Name of Conf., City of Conf., Country of Conf., pp. xxx-xxx (YEAR).
example
[4] Popescu M., Staton D.A., Thermal aspects in power traction motors with permanent magnets, Proceedings of XXIII Symposium Electromagnetic Phenomena in Nonlinear Circuits, Pilsen, Czech Republic, pp. 35-36 (2016).

Book, book chapter and manual
[5] Author1 A., Author2 A.B., Title of book, Name of the publisher (YEAR).
example
[5] Zienkiewicz O., Taylor R.L., Finite Element method, McGraw-Hill Book Company (2000).

Patent
[6] Author1 A., Author2 A., Title of patent, European Patent, EP xxx xxx (YEAR).
example
[6] Piech Z., Szelag W., Elevator brake with magneto-rheological fluid, European Patent, EP 2 197 774 B1 (2011).

Thesis
[7] Author A., Title of thesis, PhD Thesis, Department, University, City of Univ. (YEAR).
example
[7] Driesen J., Coupled electromagnetic-thermal problems in electrical energy transducers, PhD Thesis, Faculty of Applied Science, K.U. Leuven, Leuven (2000).

For on electronic forms
[8] Author A., Title of article, in [Title of Conference, record as it appears on the copyright page], [copyright year] © [applicable copyright holder of the Conference Record]. doi: [DOI number].
example
[8] Kubo M., Yamamoto Y., Kondo T., Rajashekara K., Zhu B., Zero-sequence current suppression for open-end winding induction motor drive with resonant controller, in IEEE Applied Power Electronics Conference and Exposition (APEC), © APEC, 2016, doi: 10.1109/APEC.2016.7468259

Website
[9] http://www.aee.put.poznan.pl, accessed April 2010.,

Proofs:

Authors will receive proofs for correction, which should be returned promptly. All joint contributions must indicate the name and address of the authors to whom proofs should be sent.,

Fees for printing the papers in AEE:

AEE is published in Open Access, which means that all our articles on the Internet are available for readers free of charge, however it is requested that the authors pay an article-processing charge (reviewing, editing, proofreading, checking for plagiarism, distribution and so on) in order for their articles to be published and made freely available online immediately on publication.
The fee for the publication of an article in the AEE journal is 210 Euro.,

Abstracting & Indexing:

Archives of Electrical Engineering is covered by the following services:

  • Arianta
  • Baidu Scholar
  • BazTech
  • Celdes
  • CNKI Scholar (China National Knowledge Infrastucture)
  • CNPIEC
  • DOAJ
  • EBSCO - TOC Premier
  • EBSCO (relevant databases)
  • EBSCO Discovery Service
  • Elsevier - Compendex
  • Elsevier - Engineering Village
  • Elsevier - SCOPUS
  • Genamics JournalSeek
  • Google Scholar
  • ICI Journals Master List
  • Inspec
  • J-Gate
  • Naviga (Softweco)
  • POL-Index
  • Primo Central (ExLibris)
  • ProQuest - Advanced Technologies Database with Aerospace
  • ProQuest - Electronics and Communications Abstracts
  • ProQuest - Engineering Journals
  • ProQuest - High Tech Research Database
  • ProQuest - Illustrata: Technology
  • ProQuest - SciTech Journals
  • ProQuest - Technology Journals
  • ProQuest - Technology Research Database
  • SCImago (SJR)
  • Summon (Serials Solutions/ProQuest)
  • TDOne (TDNet)
  • TEMA Technik und Management
  • Thomson Reuters - Emerging Sources Citation Index
  • Ulrich's Periodicals Directory/ulrichsweb
  • WorldCat (OCLC)
,

Open Access policy

Archives of Electrical Engineering jest czasopismem wydawanym w wolnym dostępie na licencji CC BY-NC-ND 4.0.

Archives of Electrical Engineering is an open access journal with all content available with no charge in full text version. The journal content is available under the licencse CC BY-NC-ND 4.0.

This page uses 'cookies'. Learn more