Applied sciences

Archives of Civil Engineering

Content

Archives of Civil Engineering | 2013 | No 4 |

Abstract

The reverse bending and straightening test is conducted on wires used for civil engineering applications to detect laminations which can pose a threat to the integrity of the wires. The FE simulations of the reverse bending and straightening of wires with laminations revealed that the reverse bending and straightening test is only effective in revealing or detecting near-surface laminations with lengths from 25 mm located up to 30% of the wire’s thickness and may not be an effective test to detect mid-thickness, near-mid-thickness, and short near-surface laminations with lengths below 15 mm. This is because wires with mid-thickness, near-mid-thickness and short near-surface laminations will pass through the reverse bending and straightening procedures without fracturing and therefore mid-thickness, near-mid-thickness and short near-surface laminations may go undetected. Consequently, other in-line non destructive testing methods might have to be used to detect mid-thickness, near-mid-thickness and short near-surface laminations in the wires.

Go to article

Abstract

The basis for calculating of resistance of welded RHS connections is provided by codes and international guidebooks. In the matter of calculation of the resistance of welded joints, the European standard contains very general recommendations without specifying the detailed calculation procedures, which (the) designers could use in their work. Estimation of resistance of welded semi-rigid joints is a complex issue because it requires determining of effective lengths of welds, their placement on the member walls with their different rigidity, and distribution of components of the load acting on each section of welds in various joint areas. In this paper an approximate assessment is suggested of the resistance of the welded connection in the overlapped K type joints, made of rectangular hollow sections.

Go to article

Abstract

The mechanical characteristics of the railway superstructure are related to the properties of the ballast, and especially to the particle size distribution of its grains. Under the constant stress-strain of carriages, the ballast can deteriorate over time, and consequently it should properly be monitored for safety reasons. The equipment which currently monitors the railway superstructure (like the Italian diagnostic train Archimede) do not make any “quantitative” evaluation of the ballast. The aim of this paper is therefore to propose a new methodology for extracting railway ballast particle size distribution by means of the image processing technique. The procedure has been tested on a regularly operating Italian railway line and the results have been compared with those obtained from laboratory experiments, thus assessing how effective is the methodology which could potentially be implemented also in diagnostic trains in the near future.

Go to article

Abstract

In this paper, transient analysis on heat transfer across the residential building roof having various materials like wood wool, phase change material and weathering tile is performed by numerical simulation technique. 2-dimensional roof model is created, checked for grid independency and validated with the experimental results. Three different roof structures are included in this study namely roof with (i). Concrete and weathering tile, (ii). Concrete, phase change material and weathering tile and (iii). Concrete, phase change material, wood wool and weathering tile. Roof type 3 restricts 13% of heat entering the room in comparison with roof having only concrete and weathering tile. Also the effect of various roof layers’ thickness in the roof type 3 is investigated and identifi ed that the wood wool plays the major role in arresting the entry of heat in to the room. The average reduction of heat is about 10% for an increase of a unit thickness of wood wool layer.

Go to article

Abstract

Investor bears responsibility for proper preparation of the investment process. One of his tasks is to prepare the project documentation and obtaina building permit. Frequently, during his work, there are situations and events whose im pact interferes with the design solutions. Regardless of reasons, alterations to a project constitute a source of cost risk. In each case, the Investor should be prepared for this type of a risk. Exposure to risk should be taken into account in the planning stage of the investment. Also, a model of investment execution should be chosen at this stage. The type of model is associated with the distribution of risk throughout the project. The aim of this paper is to identify events that generate risk related to alterations to Project Documentation in the context of the selection of the investment executionmodel.

Go to article

Abstract

This paper presents numerical simulationsof the behavior of a sandy layer subjected to a cyclic horizontal acceleration in shaking table tests, with a particular attention focused on the settlements of a dry sand layer, and on the liquefaction of saturated sand. A compaction/liquefaction model (C/L) is applied to these simulations. The infl uence of specifi c parameters of the model on the compaction and liquefaction of a sandy layer is shown and discussed. The results of simulations are compared with selected experimental data.

Go to article

Abstract

The article aims to evaluate the Portuguese building stock energy policies and strategy for energy saving in buildings among the EU members. It was found out the average heat transfer coefficients of the main structural elements of Portuguese Buildings and analyzed the U-values of this elements considering different time periods.

The fundamentals of this study were funded by the Agency for Development and Innovation (ADI) and co-financed by the European Regional Development Fund (FEDER) through the Operational Program for Competitiveness Factors (POFC) assigned to the Building Physics and Construction Technology Laboratory with the reference SB Tool SPT_2011_4.

Go to article

Abstract

In this paper, the distances between pedestrian crossings in twenty one places in the city of Wrocław, together with their evaluation by the researched groups of students, were analyzed. The database created from the collected questionnaires contains a set of two-dimensional variables: the distance between crossings and the rating of the students. The database set was analyzed using a fuzzy data mining approach to create particular clusters. Various numbers of clusters were analyzed, and the division of data into three clusters made it possible to relate the analysis to the LOS methodology. Each variable was enriched with a third dimension representing a membership value. The obtained evaluated distances are similar to values recommended in literature, although the distances highly evaluated by the students do not often occur in reality. This might suggest that there is the need to create new crossings, especially in the city centre, where pedestrian traffic is or should be important.

Go to article

Abstract

Communication noise is classified as one of the pollutions for the current environment. Experimental techniques to measure tire-pavement noise generation from asphalt pavements in the laboratory have been limited. A series of experiments were conducted on six different asphalt mixtures to determine if Purdue University’s Tire-Pavement Test Apparatus (TPTA) could be used to overcome these limitations. The procedure produced samples with low tire-pavement noise; however, the air void contents of the samples were higher than designed. Despite these difficulties, the sample preparation technique and the TPTA testing protocol were shown to offer an effective approach for quick laboratory assessment of tire-pavement noise characteristics of hot mix asphalt pavements at a substantially reduced cost compared to field testing.

Go to article

Editorial office

Editor-in-Chief
Henryk Zobel


Deputy Editor-in-Chief
Mariola Książek


Scientific Advisory Committee
:
Andrzej M. Brandt
Werner Brilon (Germany)
Jacek Chróścielewski
Luc Courard (Belgium)
Andrzej Garbacz
Andrzej Garstecki
Wojciech Gilewski
Marian Giżejowski
Oleg Kapliński
Piotr Konderla
Aleksander Kozłowski
Marian Kwietniewski
Zbigniew Młynarek
Andrzej S. Nowak (USA)
Anna Siemińska-Lewandowska
Jan Szwabowski
Waldemar Świdziński
Andrew P. Tarko (USA)
Marian Tracz
Edmundas K. Zavadskas (Lithuania)
Jerzy Ziółko

Secretary
Katarzyna Orzeł

Contact

 

Politechnika Warszawska

Wydział Inżynierii Lądowej

Al. Armii Ludowej 16, 00-637 Warszawa, Polska Pokój 618; Telefon 22 234 62 84

e-mail: ace@il.pw.edu.pl;

website: http://ace.il.pw.edu.pl

 

 

 

Instructions for authors

GUIDELINES FOR AUTHORS

1. Preparation of the paper

General: Author is responsible for the Paper contents including copyrights and text formatting. The manuscript should be written in English. It should be typed using 12 p TNR font with 1.5 line spacing, on single-sided A4 sheets with 2 cm margins. The paper should not exceed 10 pages including tables and figures plus 2 pages of an extended summary (TNR 10 pt. justify align), started from new page at the end of the manuscript. Summary in Polish for Polish natives only, others - summary in English.

The first page and the main text: The first page of the article should contain: (1) the title of the article, (2) the name, academic merits, affiliation and e-mail of each author, (3) the name and the address of the author to whom correspondence, proofs and reprints should be sent, (4) a summary of 50-150 words, (5) a list of key words (not to exceed 8). The main text should be divided into numbered (1, 2, etc.) and titled sections and, if needed, into subsections (1.1, 1.2, ... in Section 1, 2.1, 2.2, ... in Section 2, etc.). The abstract of 50-150 words is required on a separate sheet. Polish natives authors only are requested to enclose Polish translation of the abstract, others - abstract in English.

Tables and figures: Tables and figures should be inserted into the text (black-and-white figures and glossy photographs),numbered consecutively and titled. They should be referred to in the text as Fig. 1, Fig. 2, ..., Table 1, Table 2. A list of figures and tables captions (TNR 11 pt. left align, in Polish - for Polish natives only and in English) should be provided on separate sheet(s) at the end of the manuscript beforean extended summary. Colour figures will be accepted only if the colour is essential for the explanation.

Units and mathematical formulae: SI units and abbreviations are obligatory. Mathematical formulae should be typewritten and centred. The formulae referred to in the text are to be numbered consecutively in each Section, i.e. (1.1), (1.2), ... in Section 1, (2.1), (2.2), ... in Section 2, etc. The numbers should be placed in parentheses ( ) at the left margin. The formulae are to be referred to in the text as Eq. (1.1),, Eq. (1.2), ..., Eq. (2.1), Eq. (2.2), ..., etc. The formulae not referred to in the text should not be numbered.

Bibliography: References are to be listed at the end of the paper in the alphabetical order and consecutively numbered. A reference to a published paper should be referred to in the text by the last name(s) of author(s) and the reference's number in brackets [ ]. Each item should contain full bibliographical data in the format illustrated by the following examples:

[1] M. Abramowitz and I. A. Stegun, Eds. Handbook of Mathematical Functions (Applied Mathematics Series 55). Washington, DC: NBS, 1964, pp. 32-33.

[2] M. Gorkii, “Optimal design”, Dokl. Akad. Nauk SSSR, vol. 12, pp. 111-122, 1961.

(Transl.: in L. Pontryagin, Ed., The Mathematical Theory of Optimal Processes. New York: INTERSCIENCE, 1962, Ch. 2, sec. 3, pp. 127-135).

[3] B. Klaus and P. Horn, Robot Vision. Cambridge, MA: MIT Press, 1986.

[4] E. F. Moore, “Gedanken-experiments on sequential machines”, in Automata Studies

(Ann. of Mathematical Studies, no. 1), C. E. Shannon and J. McCarthy, Eds. Princeton, NJ: Princeton Univ. Press, 1965, pp. 129-153.

[5] R. L. Myer, “Parametric oscillators and nonlinear materials”, in Nonlinear Optics, vol. 4, P. G. Harper and B. S. Wherret, Eds. San Francisco, CA: Academic, 1977, pp. 47-160.

[6] L. Stein, “Random patterns”, in Computers and You, J. S. Brake, Ed. New York: Wiley, 1994, pp. 55-70.

[7] Westinghouse Electric Corporation (Staff of Technology and Science, Aerospace Div.), Integrated Electronic Systems. Englewood Cliffs, NJ: Prentice-Hall, 1970.

[8] G. O. Young, “Synthetic structure of industrial plastics”, in Plastics, vol. 3, Polymers of Hexadromicon, J. Peters, Ed., 2nd ed. New York: McGraw-Hill, 1964, pp. 15-64.

In special cases, other formats related to codes, reports, dissertations, etc. will be accepted.

Layout of the text can be downloaded from ace website: http://ace.il.pw.edu.pl

2. Submission of the paper

Two electronic versions of the manuscript (DOC and PDF file) and License to publish should be submitted and sent directly to the Editor-in-chief by e-mail to: ace@il.pw.edu.pl

Signing license agreement is required.

3. Proof read: Proofs will be sent to the corresponding author to correct any typesetting errors. Alterations to the original manuscript at this stage will not be accepted. Corrected proofs page must be mailed to the Editorial Office as soon as possible.

4. Copyright: Submission of a paper to Archives of Civil Engineering implies that the material is an original and unpublished work, not under consideration for publication elsewhere. If permission for publication of any material is required, it should be obtained from appropriate sources by the author. The corresponding author is responsible for the other authors' approval of the paper publication.

5. Reprints: The corresponding author will receive ten reprints and PDF file of the published paper free of charge.

6. Other information: Apart from research papers, other articles such as review papers, brief notes, discussions and reports may be published in the journal. Monographic papers and state-of-the-art papers are accepted after prior approval of the Editor. Reports on important conferences held in Poland may also be published. Editor decides whether the paper fulfil all requirements i.e. formal and scientific. Editor nominates two reviewers, who shall forward reviews of the accepted publication.

The paper will be published in ACE provided that the reviews are positive. If reviewers have some comments authors have to correct the paper. Papers are subject to open discussion. All letters should be addressed to the Editorial Office and will be published together with the authors' response.

7. Fees: Submission of the paper is free of charge. Submitted papers are accepted for publication after a positive opinion of two independent reviewers. When publication accepted Author will be informed by email about article processing charge incl. amount and payment deadline. ACE is non for profit and all fees are calculated to cover operational costs only. Payment is required to the following bank account:

OFICYNA WYDAWNICZA POLITECHNIKI WARSZAWSKIEJ

ul. Polna 50, 00-644 WARSAW

PKO IV Department in WARSAW

Number: PL 84 1240 1053 1111 0000 0500 5707

with annotation: "Author(s) name and surname, ACE"

This page uses 'cookies'. Learn more